LINDY 32118 Display Port 1.4 Edid Emulator User Manual

DisplayPort 1.4 EDID Emulator
User Manual

Introduction

Thank you for purchasing the Lindy DisplayPort 1.4 EDID Emulator. This product has been designed to provide trouble free, reliable operation. It benefits from both a LINDY 2-year warranty and free lifetime technical support. To ensure correct use, please read this manual carefully and retain it for future reference.
The Lindy DisplayPort 1.4 EDID emulator adapter is designed for systems that require EDID signals to be continuously provided without interruption and help overcome EDID related problems which can occur when using AV/KVM Extenders, Switches and Splitters.

Package Contents

• DisplayPort 1.4 EDID Emulator
• This Manual

Features

• Supports EDID Learning and EDID Emulation
• Headless connection
• Supports resolutions up to 7680×4320@30Hz or 3840×2160@144Hz
• Powered via DP Source

Installation and Use

The EDID emulator contains pre-set EDID information for many commonly used resolutions and refresh rates, please refer to the table on the following page.

Cloning procedure

1. Firstly, ensure the display and source devices are turned on.
2. Insert a DisplayPort cable from the targeted display to the EDID Emulator.
3. Connect the EDID emulator into the DisplayPort source device.
4. With a small pin click the button on the top of the Emulator to start the cloning process. The LED on the top of the unit will flash blue for approximately 5 seconds. Once the LED is a solid blue light the cloning process is complete.

Restore to default EDID
Note: This process does not require a DisplayPort cable connected to the Emulator or the display

1. Connect the Emulator to the source device.
2. With a small pin click the button on the top of the Emulator. The LED will start to flash blue for approximately 5 seconds. Once the LED has turned off the Emulator has now been reset to the pre-set EDID.

Example for use with extender:

Example for use with a switch:

Pre-set EDID Data

Video EDID:

Please Note: in addition to the default EDID resolutions, there may be some different resolutions based on the source device and display capabilities.

Audio EDID:
LPCM 2-channel, 16/20/24-bit depths at 32/44.1/48kHz

Troubleshooting

Windows shows a “Generic Non-PnP Monitor” is connected – Please ensure that the emulator is directly connected to the DP Source by its Male connector.
EDID Data is not cloned – Repeat the steps above, taking care to attach the DP cable from the display to the Emulator.

Recycling Information

WEEE (Waste of Electrical and Electronic Equipment), Recycling of Electronic Products
Europe, United Kingdom
In 2006 the European Union introduced regulations (WEEE) for the collection and recycling of all waste electrical and electronic equipment. It is no longer allowable to simply throw away electrical and electronic equipment. Instead, these products must enter the recycling process. Each individual EU member state, as well as the UK, has implemented the WEEE regulations into national law in slightly different ways. Please follow your national law when you want to dispose of any electrical or electronic products. More details can be obtained from your national WEEE recycling agency.

CE/FCC Statement

CE Certification
LINDY declares that this equipment complies with relevant European CE requirements.
UKCA Certification
LINDY declares that this equipment complies with relevant UKCA requirements.
FCC Certification
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
You are cautioned that changes or modification not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Hersteller / Manufacturer (EU):.
LINDY-Elektronik GmbH
Markircher Str. 20
68229 Mannheim
Germany
Email: info@lindy.com ,
T: +49 (0)621 470050| Manufacturer (UK):
LINDY Electronics Ltd
Sadler Forster Way
Stockton-on-Tees, TS17 9JY
England
sales@lindy.co.uk ,
T : +44 (0)1642 754000
---|---

Tested to comply with FCC standards.
For home and office use. No. 32118
1st Edition, January 2023
lindy.com

References

• Lindy Electronics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>