ADLER AD 7915 Portable Air Cooler User Manual
- June 4, 2024
- ADLER
Table of Contents
AD 7915
user manual
A
B
C
SAFETY CONDITIONS. IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE READ
CAREFULLY AND KEEP FOR FUTURE REFERENCE
The warranty conditions are different, if the device is used for commercial purpose.
- Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
- The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
- The appliacable voltage is 220-240V, ~ 50Hz. For safety reasons it is not appropriate to connect multiple devices to one power outlet.
- Please be cautious when using around children. Do not let the children to play with the product. Do not let children or people who do not know the device to use it without supervision.
- WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children, unless they are over 8 years of age and these activities are carried out under supervision.
- After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
- Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it of f from the network, unplug the power.
- Never put the power cable, the plug or the whole device into the water . Never expose the product to the atmospheric conditions such as direct sun light or rain, etc.. Never use the product in humid conditions.
- Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.
- Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defected product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
- Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
- Never use the product close to combustibles.
- Do not let cord hang over edge of counter.
- Do not immerse the motor unit in water.
- Do not insert fingers or any other objects in the housing grille of the device.
- Do not block the outlet.
- When done, prior to putting it away, unscrew the cap at the bottom of the base to drain water from the device.
- If the device is not used for a long time, unplug it from the power source.
- Always use new batteries to replace the drained batteries in the remote control.
- Do not move the device when the inner tank is filled with water.
- Do not place any objects on the device.
- The device can be used only with properly working ventilation.
DEVICE DESCRIPTION (Fig. A).
- Air outlet opening
- Water level indicator
- Wheels
- Carrying handle (on both sides)
- Mesh filter
- 2 plastic boxes with gel to frozen
- Water tank
- LED Touch control panel
- Remote Control
- Mesh filer’s frame
USING THE DEVICE
A noticeable reduction in the temperature of the outlet air occurs after putting into the water tank plastic containers attached to the product previously frozen in the freezer. It is recommended to fill the tank with cold tap water.
-
Place the unit on a dry, flat surface and connect to the power supply.
-
Pull out the water tank (7) from the back of the machine and pour in the water (Fig. B). Be careful not to exceed the maximum level.
-
Turn on the device using the “ON/OFF ” button on the control panel (Fig. C).
-
The SPEED button on the control panel allows you to change the speed of the blower unit. The following speeds can be selected:
HIGH (fast), MIDDLE (medium) and LOW (slow). -
COOL button lowers the temperature of the air by running the water pump. Additionally, a set of two boxes is attached. Boxes are filled in special gel that is able to frozen and unfrozen and no need to open them. To use them, put them on 24 hours inside the freezer. Then put one or both of ice boxes into water tank (7). To blow the cool air, the device must be filled with water. When the device is operating, periodically check the water level to see whether to add water.
-
Pressing the SWING button starts the oscillation of vertical slats that provide even distribution of cold air stream in range 120°. Horizontal slats do not move automatically, so if necessary, manually adjust them to point up or down.
-
The TIMER button allows for programming the amount of time during which the device will operate before turning itself off automatically (if the TIMER function is not used, the device will work until it is manually turned off). Time range 1 - 12 hours.
-
The MODE button allows for changing the fan mode. In addition to the normal mode, you can select “NATURE” and “SLEEP.” The NATURE mode mimics the natural wind action by repeating the fan speed sequence: middle speed (12 seconds) -> low speed (6 second) -> high speed (3 seconds) -> middle speed (6 second) -> low speed (6 second). The ,,SLEEP” mode operated in repeating the fan speed sequence: middle speed (6 seconds) -> low speed (3 seconds).
-
The button on remote control (9) is same as the control panel (8). Don’t put the stuff in the front of the remote control receivers.
CLEANING AND MAINTENANCE
-
Clean with soft, dry cloth. Do not use chemical solvents because they can cause permanent damage or deformation of the device.
-
If the device is not used for three or more months, take the batteries out of the remote control.
-
After long time operation, the mesh filter (5) and mesh filer’s frame (10) will be clogged with the dust, which will greatly affect the machine’s performance of cooling. If long time no changing water, there may be mold and mildew. We suggest to clean the mesh filter (5) and mesh filer’s frame (10) once every two weeks. The clean procedure is as below:
a) Unplug the device, remove the screw of the back housing and then take the frame and filter out.
b) Wash the filter in a mild detergent and warm water solution, then rinse in clean water.
c) Wash the mesh filer with flowing clean water. Use a soft brush for cleaning. -
Drain the water before storage by removing the drain plug at the bottom of the water tank. Then dry the device, mesh filter, mesh filter’s frame and housing to aviod the moisture damage.
TECHNICAL DATA:
Power source: 220-240 V ~50 Hz
Power: 65 W
Tank capacity: 7 liters
Power Max: 350 W
Water Consumption: 0,5 - 0,6 liter / hour
Device is made in class I of insulation and has to be connected only to power outlet with ground circuit. Device is compliant with EU directives:
Low voltage directive (LVD)
Electromagnetic compatibility (EMC)
Device marked CE mark on rating label
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may effect the environment. Do not dispose this appliance in the common waste bin.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>