ErGear EGESD5B-4 Electric Standing Desk Adjustable Height Instruction Manual

ErGear EGESD5B-4 Electric Standing Desk Adjustable Height

Electric Standing Desk

Specifications

• Power Input : 100V-240V
• Max. Speed : 21mm/s
• Operating Noise : 52dB
• Max. Load : 176 lbs / 80 kg

Product Usage Instructions

Step 1: Assembling the Leg Sections

1. Attach the crossbars by aligning the small round protrusions with the round holes on the crossbars.
2. Attach the side plates using the provided bolts, but do not fully tighten them yet.
3. Slightly loosen the four pre-installed bolts on the crossbars.

Step 2: Assembling the Desktop

1. Connect the desktop panels using the wood dowel pins.
2. Secure the desktop panels with the connectors using a drill (with suitable torque and speed) or a Phillips screwdriver.

Step 3: Attaching the Frame to the Desktop

1. Place the vertical support bar and middle crossbar on the desktop, aligning their screw holes with the large screw hole on the desktop.
2. Loosely thread the bolt through the middle crossbar and vertical support bar, then into the desktop.
3. Slide two leg sections onto the middle crossbar and adjust them to align their screw holes.
4. Fully tighten the four pre-installed bolts on the crossbars to secure the frame to the desktop.

Step 4: Attaching the Transmission Rod
Before attaching the transmission rod, measure the heights of the two desk legs to ensure they are at the same level. If not

1. Insert the transmission rod into the hole in the left leg.
2. Turn the rod clockwise to raise the left leg or anti-clockwise to lower it until both legs are level.

FAQ

• Q: What tools do I need to assemble the desk?
  A: You will need a drill or a Phillips screwdriver (not included) to assemble the desk.

• Q: What is the maximum load capacity of the desk?
  A: The desk can support a maximum load of 176 lbs / 80 kg.

• Q: How do I adjust the height of the desk?
  A: The desk can be adjusted using the provided controller.

Electric Standing Desk
Instruction Manual

EGESD25B / EGESD25W
EGESD26B / EGESD26WN

Rev00(A)

1-800-651-9525 (US/CA) Mon–Fri, 8am–8pm (CST)
44-808-196-3875 (UK) Mon–Fri, 2pm–10pm (UTC)

support@ergear.com

https://ergear.com

Tools Needed (Not included)

Specifications

Height Adjustment Range 28.4”–46.5” (72-118cm)

Step 1: Supplied Parts and Hardware

Step 2

Step 3

Step 4

Step 5 Step 6

Step 7

Step 8

Step 9

Step 1 Assembling the Leg Sections

Attach the crossbars.
To install correctly, align these small round protrusions with the round holes on the crossbars.

Attach the side plates.

Screw in the bolts, but do not fully tighten them until all four bolts are in place.

Slightly loosen four pre-installed

Step 2 Assembling the Desktop
Connect the desktop panels using the wood dowel pins.

Secure the desktop panels with the connectors.
You can use a drill (with suitable torque and speed) or a Phillips screwdriver.

Step 3 Attaching the Frame to the Desktop
Place the vertical support bar and middle crossbar on the desktop, and pay attention to their positions. Also, make sure their screw holes are aligned with large screw hole on the desktop. Loosely thread the bolt through the middle crossbar and vertical support bar, then into the desktop.

Slide two leg sections onto the middle crossbar.

Adjust two leg sections. Ensure the screw holes are aligned.

Fully tighten four pre- installed bolts on the crossbars securing the frame.

Secure the frame to the desktop.

Step 4 Attaching the Transmission Rod
Before attaching the transmission rod, measure the heights of the two desk legs to see if they are set at the same level. If not, insert the transmission rod into the hole in the left leg. Turn the rod to adjust the left leg so it’s level with the right leg. Turn the rod clockwise to raise the left leg or anti-clockwise to lower it.

Ensure the transmission rod is properly inserted into the hole in the left leg. Slide the rod coupler to the right to connect with the other end of the transmission rod.

Use the set screws to secure the rod coupler.

Step 5 :Attaching the controller and the storage hooks

Step 6 Attaching the Cable Management Tray
Fold the cable management tray [13] along the dashed line.

Step 7 Connecting the Cables

Step 8 Attaching the Power Outlet
Press the button to open the cover. Separate the power outlet by loosening the pre-installed bolts, and save them for later use.

Secure the power outlet box to the desktop.

Secure the other part to the power outlet box.

Step 9 Installing the Cable Hole Cover

Using the Controller

• Note : After initial power-on, the screen will show the current height. If the displayed height doesn’t match the actual height or if the desk legs are unequal, please follow the reset instructions.
• Reset

1. 1. Press and hold the button until the desk goes down to its lowest level, and then release the button.

2. Press and hold the button until ‘rst’ is displayed. Continue holding until the desk goes down to its lowest level and comes back up slightly. Release the button with the current height displaying, and reset is complete. If the button is released during the reset procedure, reset will stop. The desk won’t work until reset is done correctly.

• Save Current Height Setting
  Press and hold the button for 3 seconds. The screen will show ‘S-1,’ and the current height will be saved to that button. Short-press the button, and the desk will move to the height that was previously set for that button. Press any button to stop the desk.

• Save Current Height Setting
  Press and hold the button for 3 seconds. The screen will show ‘S-2,’ and button for 3 seconds. The screen will show ‘S-2,’ and button , and the desk will move to the height that was previously set for that button. Press any button to stop the desk.

• Raise the Desk
  Press the button to raise the desk continuously until it reaches the high-est position of 116cm or the button is released.

• Lock/Unlock
  Press and hold and buttons together for 5 seconds to turn the lock on. The screen will display ‘Loc’ and the buttons will be disabled. Repeat to turn the lock off again.

• Power-Saving Mode
  The screen will turn off if there is no button-press for a minute. Any button- press will turn the screen on again.

Thank you for choosing this ErGear product. At ErGear we strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us.

• 1-800-651-9525 (US/CA) Mon–Fri, 8am–8pm (CST)
  44-808-196-3875 (UK) Mon–Fri, 2pm–10pm (UTC)

• support@ergear.com

• https://ergear.com

• 860-02063-00 Rev00

References

• Complete Flexibility. Total Freedom – ErGear

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>