HAOHUALIANHE A31 Remote Control User Manual
- June 15, 2024
- HAOHUALIANHE
Table of Contents
HAOHUALIANHE A31 Remote Control
Product Information
Specifications:
- CMIIT ID: XXXXX
- Adjustable Width: 63mm-95mm (Single clip expansion), 142mm-260mm (Double clip extension)
- Twist Head: Loosen to adjust the angle up and down
- Modes: Vertical mode, Horizontal mode
- Anti-Skid Collet: Push back to open and clamp the mobile phone or tablet PC
- PTZ Screw: 1/4 inch, compatible with general photography accessories
- Executive Standard: Q/HHLH 003-2019
Product Usage Instructions
Step 1: Single Clip Expansion and Double Clip Extension
To adjust the width of the bracket, follow these steps:
- For Single Clip Expansion: Loosen the twist head and adjust the width between 63mm and 95mm.
- For Double Clip Extension: Loosen the twist head and adjust the width between 142mm and 260mm.
Step 2: Angle Adjustment
To adjust the angle of the bracket, follow these steps:
- Loosen the twist head to freely adjust the angle up and down.
- After the desired angle is set, lock the twist to secure the position.
Step 3: Modes
The bracket can be used in two modes:
- Vertical Mode: Keep the bracket in an upright position.
- Horizontal Mode: Rotate the bracket to a horizontal position.
Step 4: Anti-Skid Collet
To clamp a mobile phone or tablet PC, follow these steps:
- Push back the anti-skid collet to open it.
- Place the mobile phone or tablet PC between the collet jaws.
- Release the anti-skid collet to securely hold the device.
Step 5: PTZ Screw
The bracket features a 1/4 inch PTZ screw for attaching general photography accessories. Simply screw in the accessory to use it with the bracket.
Step 6: Remote Control Pairing
To pair the remote control with your mobile phone, follow these steps:
- Long press the remote control for three seconds until the blue light starts flashing.
- In your mobile phone’s settings, search for and click on”ADYSS” to establish a connection.
- If the blue light goes off, it indicates a successful pairing.
- The effective distance between the remote control and mobile phone is 10 meters.
- The remote control will automatically turn off after 5 minutes of inactivity.
- When using the remote control again, it will automatically connect to the last paired mobile phone. For a new mobile phone, click on the Bluetooth name to establish a connection.
Step 7: Camera Screw
To use the camera screw, follow these steps:
- Pull out the tripod from the bottom of the bracket.
- Open the three feet of the tripod outward for stability.
- To unfold the threaded sliding sleeve, press and hold it while pulling it down until it reaches the end.
- To retract the threaded sliding sleeve, press and hold it while pulling it up.
Step 8: FCC Compliance
This device complies with part 15 of the FCC Rules. It is subject to the following conditions:
- The device must not cause harmful interference.
- The device must accept any interference received, including interference that may cause undesired operation.
- Any changes or modifications not approved by the responsible party may void the user’s authority to operate the equipment.
FAQ
Q: What is the adjustable width range of the bracket?
A: The bracket can be adjusted between 63mm and 95mm in single clip expansion mode and between 142mm and 260mm in double clip extension mode.
Q: What is the effective distance between the remote control nd mobile phone?
A: The effective distance is 10 meters.
Q: How long does the remote control stay turned on?
A: The remote control will automatically shut down after 5 minutes of inactivity.
Q: How does the remote control connect to a new mobile phone?
A: For a new mobile phone, click on the Bluetooth name to establish a connection.
Welcome to use multi-function bracket Connection steps:
- Press and hold the power button “ “for 2 seconds to turn on the device.
- Wait until the blue light is on
- Open phone settings, search for link devices
- Click “ADYSS” to connect the device and wait for 5 seconds.
- The blue light is brightly paired successfully.
Supported mobile phone model:
- Apple series models (iOS 5.0 and above)
- Android series models (Android 4.2.2 and above)
- Please update your phone system on time to avoid the version being too low to be compatible for use.
Matters need attention (not involved in the warranty)
- Before using the selfie stick, please make sure that the phone is properly fixed on the collet, and the damage caused by the smartphone falling off.
- Please confirm the place of using region and facility restrictions before using, and prohibit the behaviour of public property violations.
- Pulling and rotating the power cord during the use period causes a short circuit.
- Falling from a high place causes damage to the outer casing.
- Using a power supply that exceeds the product load causes the product to heat up and the circuit board to burn out.
- Do not place the product in a low-temperature and humid place.
- Do not throw the product into the fire and keep away from the fire.
- Warning: Contains small parts. Not suitable for children 3 years old and below.
One-Year Limited Warranty Summary
ADYSS warranted that the delivered hardware product to be free from defects in materials and workmanship for a period of one year from the original retail purchase date, and the after-sales problem can be accepted. ADYSS would not guarantee neither the normal use of wear nor the damage caused by accident or abuse. Visit a retail store owned by ADYSS or ADYSS Authorized Service Providers for the service, where you can have the product repaired accordingly. Replacing your warranty rights is not included in the additional rights provided by local consumer law. When you make a claim according to this warranty policy, you may need to provide the detail information of proof of purchase.
Executive standard: Q/HHLH 003-2019
Product operation steps
- Loosen the twist head and adjust the angle up and down. After the angle adjustment is completed, lock the twist
- Vertical mode Horizontal mode
- Push back the anti-skid collet ” “
- The anti-skid chuck can beopened to clamp the mobile phone or tablet PC ” “
- Long press” “for three seconds and blue light will flash, mobile phone settings search: ” ADYSS ” click the link, If the blue light goes off, it means that the pair has been successfully paired. Turn on the camera to take photos and video.
- The remote control is connected to the mobile phone, the effective distance of the remote control is 10 meters, the remote control is turned on for three seconds, the remote control does not operate, and it will automatically shut down after 5 minutes, the paired one, the next time you open the remote control, open the Bluetooth new mobile phone will automatically connect, the old mobile phone needs to click the Bluetooth name
- 1 / 4 camera screw
- First pull the tripod out from the bottom
- Open the three feet outward
- Press and hold the threaded sliding sleeve and pull it down to the end to unfold, it can be stable ” down ” Press and hold the threaded sliding sleeve to pull up and retract ” up “
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warming for Portable device: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.