HEINNER HCNF-V291F Vertical Vacuum Cleaner and Washer User Manual
- June 15, 2024
- HEINNER
Table of Contents
HEINNER HCNF-V291F Vertical Vacuum Cleaner and Washer User Manual
1. INTRODUCTION
Please read the instructions carefully and keep the manual for future
information.
This manual is designed to give all necessary instructions concerning
installation, use and maintenance of the unit. In order to operate the unit
correctly and safely, please read this instruction manual carefully before
installation and use.
2. CONTENT OF YOUR PACKAGE
➔ Vacuum cleaner and washer
➔ User manual
➔ Certificate of warranty
➔ Declaration of conformity
3. SAFETY INSTRUCTIONS
Important!
The vacuum cleaner features 3 operating modes: normal speed with water spray,
high speed with water spray, and vacuum. To use only the vacuum function, the
“MODE” button must be pressed twice after starting the vacuum cleaner.
Otherwise, the vacuum cleaner will start washing; the default active function
is washing every time the vacuum cleaner is switched on. It is normal for the
brush to spray water in the first two modes, less so in vacuum mode.
By activating the ,,Self clean” function, the appliance will perform a cleaning of the tube and brush. It is important that the vacuum cleaner has clean water in the top tank and that it is placed in the stand. To avoid unpleasant odours and to extend the service life of the brush, we recommend that the brush is removed and thoroughly dried immediately after each use.
GENERAL
This product is suitable for use on hard floors in home environment, including
waxed floors, stone floors, rubber floors, marble surfaces, granite floors,
terrazzo floors, solid wood floors, laminate floors, bamboo floors and various
mirror tiles, porcelain tiles and other flat floor surfaces. The product may
not work optimally when used on uneven surfaces. Do not use this product near
or on flammable or explosive objects, there will be a risk of fire and
explosion. Do not use this product near a working fireplace or heater to
prevent deformation of its casing.
Do not vape hot substances (unextinguished cigarette butts, matches or hot ashes), ultra-fine substances (e.g. lime, cement, wood chips, plaster dust, ashes or charcoal dust), hazardous substances (e.g. solvents or descaling agents), chemical substances (e.g. acids or cleaning agents etc.) and other substances with uncertain physical properties. Do not use this scrubber to clean detergent, paraffin, petrol, alcohol, paint or perfume, since such liquids may cause short circuit, fire or explosion in the device. Do not use this scrubber to pick up toners and toners used inside laser printers and photocopiers, as these objects can cause fires or explosions. Do not use this scrubber to clean sharp or large objects such as shards of glass, small toys, pins, paper clips, stones, plaster or large pieces of paper which may jam or damage the device. Do not use the scrubber to clean any burning or smoking objects, such as ashes from unextinguished heat sources, burning cigarettes or matches. Stains of strong greasy, sticky or staining properties such as shoe polish, paint or pigments are not covered by this product. Do not touch the plug or any live part of the product with wet hands to avoid electric shock. Stop using the product if the plug is damaged. In such case, please call our professional maintenance staff to replace the plug to prevent any hazards. Keep airflow paths and moving parts of this product away from long hair, loose clothing, fingers and other parts of your body. Do not point vacuum hoses, attachment tips or tools at your eyes or ears, or put them in your mouth. Use cleaners made by us and our approved manufacturers, do not add other solutions to the cleaners to prevent the generation of toxic and harmful fumes. When using the product, in case of current leakage, high motor temperature and abnormal noise, such as overheating, noise, odor or weak suction force, please stop using the product immediately and call our professional maintenance personnel for help. After using the machine, please empty the wastewater tank in time to avoid odor and keep the ventilation path clear to avoid blockage causing a decrease in suction force and heating of the motor, thus affecting the service life of the scrubber. After using the machine, please store it in a dry place since humidity may affect its insulation and service life. The scrubber body and floor brush have an energized setting and cannot be soaked or rinsed with water. Please check the opening of the nozzle regularly. If it is blocked, please clear it in time to avoid blockage which may reduce the suction force and affect the performance of the product. Please make sure that the product is powered off before changing its rolling brush. In case of any of the following conditions, please do not use the product and send it to our designated service department for repair: The product has fallen off and is visibly damaged or not functioning properly. The power cord is damaged. Do not disassemble the enclosed machine yourself, there are no customer serviceable parts in this machine and do not attempt to alter the machine as this will result in danger. Use of voltages that do not comply with the specifications of the product will damage the product and may cause injury to the user. The correct voltage rating is shown on the nameplate. Due care must be taken when cleaning stairs with this product to prevent falls. Do not shake the machine up and down or bump it violently to prevent sewage from flowing into the motor. When the motor is working, do not lift or carry the product up or down, and do not place it on any of its sides or on any flat surfaces to prevent backflow water from entering the motor. To prevent tripping and falling of any person, the product should be placed against a wall after using it. Do not use the product if the clean water tank and the wastewater tank are not installed properly.
Do not place any small objects at the air outlet and do not block the outlet. Remove any small objects that may obstruct the air flow to prevent the machine from overheating. Do not get the machine wet, otherwise there will be a risk of fire due to the short circuit of the machine. All technical data and other information provided herein are obtained by us or by the appointed third-party testing company and are subject to final interpretation by us.
4. PRODUCT DESCRIPTION
5. USING THE PRODUCT
Cleaning brush
The cleaning brush has brush at one end and can be used to clean the stubborn
dirt attached to the wastewater tank and the pipes below.
Preparation before use
Assembly: Insert the end of the hand into the port of the host machine
vertically until a “click” could be heard at the bottom. Disassembly: To
disassemble the handle for storage, use a tool like a screwdriver to insert
into the round hold at the back of the machine to the bottom while pull out
the handle vertically.
Machine charging
Note: Charge the product before using it for the first time.
- Place the machine on the base.
- Insert the charging end of the adapter into the charging port of the machine (as shown in the figure above) and connect the plug to a 220V socket. The indicator will be in solid red during the charging process.
- It will take about 4-6 hours to fully charge the machine. After it is fully charged, the indicator will go off.
Filling clean water tank Note: Only the clean water tank shall be filled with water, but not the wastewater tank
- Hold the machine with one hand and press the clean water tank release button with the other hand to remove the clean water tank.
- Open the sealing cover of the clean water tank, fill the tank with tap water and close the sealing cover.
- Install the clean water tank with the sealing cover inwards on to the machine until a click can be heard.
Power on and cleaning
- To power on the machine for cleaning, step on the floor brush and pull the handle in an inclined way until a click could be heard. At this moment, the machine will be in the working condition;
- After starting work, just press the switch button to power on and start low-speed mode, indicator shows blue, and press the button again to power the machine off;
- Press the mode button to switch to high-speed mode, indicator shows blue, press the button again to switch to rapid suction mode, water pump does not spray water, indicator blue light flashes
Self-cleaning
After completing the cleaning process, Press and hold the self-cleaning button
for two seconds ot s tart the self-cleaning process, which may be completed in
40 seconds. If you want to turn off self-cleaning, please press the self-
cleaning button or switch button.
Cleaning wastewater tank
Note: After cleaning, the machine shall be placed on its base, but not any
place exposed to direct sunlight or moisture. To ensure the performance of the
machine, please maintain its parts regularly; Before cleaning the machine,
please power it off first. When using water or neutral detergent to clean the
machine, make sure that the cleaning cloth is dried to prevent water from
entering the electric elements of the machine.
- Remove the wastewater tank by pushing the tank button down with the thumb downward and pulling it outwards at the same time.
- Hold the tank with one hand and pull up the upper cover of the wastewater tank with the other hand.
- Empty the tank and use the cleaning brush to remove any deposited stains (if any) on the inner wall of the tank.
- Remove the HEPA from the wastewater tank and check if the float is caught by any foreign matter.
- After removing the HEPA, rinse the tank with clean water and fully dry it before reassembling it back in the same way.
- A click will indicate the successful installation of the wastewater tank.
Cleaning floor brush cover and rolling brush.
Note: It is recommended to clean and dry the rolling brush cover and rolling
brush timely after each use to ensure the cleanliness of the machine; Any
stains at the nozzle shall be cleaned with a wet rag. Do not flush it with
water. · Take the floor brush cover off by pressing the snaps as shown in the
figure;
- Pull the lever at the left end of the rolling brush to remove the rolling brush;
- Clean anything on the rolling brush;
- Use clean water to wash the rolling brush and its cover;
- After the cleaning is completed, pinch the brush lever with one hand, align the other side of the brush with the right end cover, then put the lever end into the slot. The brush is successfully installed.
- If the machine is not used immediately, the brush can be placed in a ventilated place to dry before installation;
- After cleaning, align the snapshot on both ends of the brush cover with the slots on both ends of the brush, rotate and press the brush cover lever until a click could be heard.
6. TROUBLESHOOTING
Please check the following table in case of any abnormal conditions, when using the cleaner
CUSTOMER CARE AND SERVICE
Always use original spare parts. When contacting our Authorised Service Centre, ensure that you have the following data available: Model and Serial Number. The information can be found on the rating plate. Subject to change without notice.
TECHNICAL DATA
Thank you for purchasing this product. If you need support with your product,
visit our website using the links below.
Get User manuals: https://www.heinner.ro
Get Service information: https://www.heinner.ro
www.heinner.com,
http://www.nod.ro
References
- Heinner – large appliances, small appliances, housekeeping, DIY
- Heinner – large appliances, small appliances, housekeeping, DIY
- NOD - Network One Distribution
- NOD - Network One Distribution
- Heinner – electrocasnice mari, electrocasnice mici, menaj, bricolaj
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>