Telemecanique TSXETG1010 Module User Guide
- June 4, 2024
- Telemecanique
Table of Contents
- Telemecanique TSXETG1010 Module
- Presentation
- Description
- Description of the Support Plate
- Mounting
- Connection of Supply Terminal Block
- Connection of RJ45 Ethernet Connector
- Connection of RS232 Modem Connector
- Connection of RJ45 Uni-Telway Connector
- Connection of Mini-Din Connector
- Diagnostics
- Electrical Characteristics
- Conditions of Use
- Standards
- Quick Setup Diagram
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Telemecanique TSXETG1010 Module
Presentation
The TSX ETG 1010 module is a stand-alone TCP/IP-Uni-Telway gateway module used to connect a Uni-Telway device to a TCP/IP network. It is a C20 class device (TR standard). It has a built-in RS232 serial link which can be used to connect an external modem. Mainly, this module is used to perform the following functions:
- UNI-TE and Modbus messaging over TCP/IP,
- SMTP service,
- SNMP service,
- Embedded Web server,
- option of having a user website.
Description
The TSX ETG 1010 module is a single format module, external to the PLC, mounted on a support plate which can be fixed to a DIN AM1-DE200 or AM1-DP200 rail, or on a Telequick AM1-PA pre-slotted mounting plate. This module is made up of the following components:
- 3 LED indicators:
- a RUN/UTW LED (green),
- an ERR LED (red),
- an ETHERNET LED (orange),
- a Mini-Din connector for a Terminal port,
- an RJ45 connector for an RS 485 Uni-Telway link,
- an RJ45 connector for an Ethernet link,
- a 9-pin SUB D connector for a modem link,
- a screw terminal block for 24 VDC power supply connection,
- a support plate for fixing the module directly to an AM1-DE200/DP200 DIN rail or to a Telequick AM1-PA pre-slotted plate.
Description of the Support Plate
- Two 5.5 mm diameter holes for fixing the plate to a panel or the AM1-PA pre-slotted mounting plate with a mounting distance of 140 mm (mounting distance for TSX Micros).
- M4 fixing hole for securing the TSX ETG 1010 module.
- Two 6.5 mm diameter holes for fixing the plate to a panel or the AM1-PA pre-slotted mounting plate with a mounting distance of 88.9 mm (mounting distance for TSX Premiums).
- Holes to be used as anchor-points for the pins situated to the rear of the module base.
Dimensions of the module with cables:
Mounting
Mounting the module on a DIN rail or Telequick plate:
Connection of Supply Terminal Block
The power supply terminal block consists of three front screw terminals. Each
terminal takes a cable of maximum width of 2.5 mm2.
Illustration:
Connection of RJ45 Ethernet Connector
- Tx+
- Tx-
- Rx+
- Not connected
- Not connected
- Rx-
- Non connected
- Not connected
Connection of RS232 Modem Connector
- Data Carrier Detect
- Received Data
- Transmitted Data
- Data Terminal Ready
- Signal Ground
- Data Set Ready
- Request to send
- Clear to send
- Ring Indicator
Connection of RJ45 Uni-Telway Connector
- Not connected
- Not connected
- Not connected
- D1/D(B)
- D0/D(A)
- Not connected
- Non-connected
- Common
Connection of Mini-Din Connector
- D(B)
- D(A)
- Reserved
- Not connected
- Not connected
- Not connected
- 0 V
- 5 V
Diagnostics
Note: The ETHERNET LED flashes according to the Ethernet communication speed and the RUN/UTW LED flashes according to the Uni-Telway communication speed.
Electrical Characteristics
| Parameter | Minimum | Nominal | Maximum |
|---|---|---|---|
| Supply voltage | 19.2VDC | 24VDC | 30VDC |
| Ripple factor | – | – | 5% |
| Permissible overvoltage (for 1 hour and for 24 hours) | – | – | 34VDC |
| Current consumption | 50ma | 100ma | 200ma |
| Power loss | – | 2.4W | 4W |
Length of a power outage
in the absence of a power supply
| –| –| 1ms
Conditions of Use
Conditions of use:
- temperature: from 0 to +60 °C,
- Relative Humidity: 10 to 95 % (without condensation),
- altitude: from 0 to 2000 m,
- vibration immunity: compliant with IEC 68-2-6 test Fc,
- shock immunity: compliant with IEC 68-2-27 test Ea,
- resistance to dropping, in packaging: compliant with IEC/EN 61131-2.
Storage conditions:
- temperature: from -25 to +70 °C,
- Relative Humidity: 5 to 95% (without condensation).
Standards
The TSX ETG 1010 module complies with the following standards:
- ISO/IEC 8802-3,
- ANSI/IEEE Std 802.3-2002,
- UL 508,
- IEC/EN 61131-2,
- CSA C22.2 N°142,
- compliance with EN55011 class A for radiated emissions,
- CE mark,
- merchant shipping classification.
WARNING
The module must be connected to ground via the power supply terminals. Failure
to observe this precaution can result in severe injury or equipment damage.
Quick Setup Diagram
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>