BRITA sodaONE Water Carbonator Black Including Instruction Manual

: May 15, 2024
: BRITA

Table of Contents

BRITA sodaONE Water Carbonator Black Including
Product Specifications
Product Usage Instructions
Instructions for use
CONTENTS
Introduction
SAFETY INSTRUCTIONS
Use
Cleaning the sodaONE soda maker and the bottle
Troubleshooting
Important information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BRITA sodaONE Water Carbonator Black Including

BRITA-sodaONE-Water-Carbonator-Black-Including-product

Product Specifications

Product Name: sodaONE Soda Maker
Model Number: XYZ123
Power Source: Manual
Material: Plastic
Capacity: 1 litre

Product Usage Instructions

Attaching the CO2 Cylinder

Unscrew the plastic cover and remove it from the cylinder head.
Lay the sodaONE on its side. Insert the cylinder into the sodaONE through the hole in the bottom and turn the cylinder in a clockwise direction until it fits securely.

Making Sparkling Water

Push the button for 2-3 seconds to carbonate the water.
Unscrew the bottle after the remaining pressure has escaped.

Cleaning Instructions

Cleaning the sodaONE Soda Maker and Bottle

Disconnect the CO2 cylinder.
Rinse the sodaONE and bottle with warm soapy water.
Dry thoroughly before the next use.

Specifications

someone soda maker
Water nozzle
someone PET bottle
Drip tray cover
CO2 cylinder

FAQ:

Q: How often should I replace the CO2 cylinder?

A: The frequency of replacing the CO2 cylinder depends on your usage. On average, a cylinder can carbonate around 60 liters of water.

Q: Can I use flavors with the sodaONE Soda Maker?

A: Yes, you can add flavors to your sparkling water after carbonation.

Instructions for use

ATTACHING THE CO2 CYLINDER

Unscrew the plastic cover and remove it from the cylinder head.
Lay the sodaONE on its side. Insert the cylinder into the sodaONE through the hole in the bottom and turn the cylinder in a clockwise direction until it fits securely.

IT’S SPARKLING WATER TIME!

Before using the bottle for the first time, rinse it with dishwashing liquid and lukewarm water. Not dishwasher safe!
Screw the water nozzle into the thread provided.
Fill the bottle with water up to the line at the top.
Screw the bottle into the thread provided.
Press the button and hold it down until you hear a hissing sound from the valve.
Unscrew the bottle after the remaining pressure has escaped.

Introduction

Thank you for choosing a soda maker from BRITA. With this product, you can turn fresh tap water into sparkling water in an instant. Making your sparkling water is simple, cost-effective, and kinder to the environment.
What’s more, you can adjust how fizzy you want your water to be. With one BRITA
CO2 cylinder you can make up to 60 litres of sparkling water. The exact quantity may vary, depending on how much fizz you prefer.
The Someone soda maker is made from high-quality materials and undergoes regular product safety and quality testing. Soda makers operate with high gas pressure levels so it is important that the included safety instructions are observed.

Correct use

The soda maker is intended for personal use and by adults only. It is intended for use only to infuse drinking water with carbon dioxide, without any further additives.
It should not be used for carbonating pre-flavored soft drinks, juices, alcoholic drinks, or any drinks that have had additives such as syrups or effervescent tablets added.
Any use beyond the intended purpose is considered misuse. BRITA shall not be liable for any damage or injury caused by misuse.

SAFETY INSTRUCTIONS

What liquids can I carbonate?

The soda maker must only be used with drinking water provided by water utilities which complies accordingly with the legal requirements for drinking water quality.
For an even better taste experience, use BRITA filtered water for carbonation. „Water is a perishable food and as such, you should always consume it within two days.“
If public authorities require that the mains water be boiled, you must also boil the water before carbonation! After boiling, the water must be allowed to cool before pouring it into the bottle.
You must only carbonate still tap water! Other drinks, such as juices, soft drinks, or tap water containing syrups may cause damage to the appliance or lead to adverse health effects.

Bottle

Please only use original BRITA sodaONE PET bottles with the sodaONE soda maker. Bottles from other manufacturers are not compatible and therefore pose a safety risk.
This applies in particular to the use of glass bottles, regardless of the manufacturer.
The BRITA sodaONE bottle is made of high-quality PET plastic with stainless steel elements. It is BPA-free and specially designed for the BRITA soda maker.
Before using it for the first time and after every other use, it must be cleaned by hand using only mild dishwashing liquid.
When using a brush, make sure it is suitable for cleaning plastic bottles and will not scratch the surface.

Not dishwasher safe

The bottle is only suitable for use in temperatures between +5° and +40° Celsius.
Do not put the bottle in the freezer.
Before every use, check the sodaONE bottle for cracks or distortions. Damaged bottles must not be used!
High pressure is created inside the bottle during carbonation, and for safety reasons, each bottle must be replaced no later than 24 months after the first use.
To avoid odors, store the empty bottle with the lid removed.

Using CO2 safely

WARNING! CO2 is a colorless, odorless gas. There is a danger of suffocation in situations with high concentrations and poor ventilation.
If you suspect increased CO2 concentration in a room, ventilate and leave the area.
Do not make any alterations to the CO2 cylinder, such as piercing it, etc.
Damaged CO2 cylinders should not be used and must be exchanged without delay!
In cases of improper use, the pressure inside a CO2 cylinder can cause serious and even fatal injuries.
When storing, CO2 cylinders can be placed vertically or horizontally, but be sure that they are prevented from rolling or falling.
For safety reasons, the cylinder must never hit the floor with the valve upfront to avoid its damage which could cause a potential gas leak.
When operating, always place CO2 cylinders in an upright position.
Full CO2 cylinders must never be exposed to direct sunlight or temperatures above +50° Celsius.
Store CO2 cylinders, whether full or empty, out of the reach of children.
The BRITA sodaONE soda maker can be operated with standard commercial 425 g CO2 cylinders, but it is recommended to use original BRITA CO2 cylinders.
Do not use larger or smaller CO2 cylinders under any circumstances.
CO2 cylinders may be very cold after use. Please wait for 10 minutes after your last use before changing the cylinder.
Always use the soda maker with full water bottles! Never fill an empty bottle with CO2.
Never attempt to fill the CO2 cylinder yourself.

Use

Select a suitable location for the BRITA soda maker on a flat, stable surface away from heat sources or open flames, such as stoves or ovens.
Always use the soda maker in an upright position.

Installing the CO2 cylinder

Screw the water nozzle into the thread provided by the soda maker.
Remove the drip tray cover and place the soda maker on its side.
Remove the seal on the cylinder head and unscrew the valve cover.
Slide the cylinder carefully into the body from the bottom.
As soon as the cylinder makes contact with the end, turn it in a clockwise direction.
Do not screw too tightly, as this may cause damage to the system or the cylinder itself.
Place the soda maker in an upright position and replace the drip tray cover.
To remove an empty cylinder, reverse the procedure used to install the cylinder, ensuring that you unscrew it in an anti-clockwise direction

It’s sparkling water time!

Before using the bottle for the first time, rinse it by hand using a mild dishwashing liquid and lukewarm water. The bottle is not dishwasher safe!
Do not fill above the ‚Max‘ marking. If the bottle is filled above this level, the water will overflow when it is carbonated.
- TIP To enjoy an even better sparkling water experience, fill the bottle with fridge-chilled, filtered water from a BRITA water filter jug.
Screw the full bottle securely into the soda maker.
Press the carbonator button down. After 2-3 seconds you will hear a clear buzzing sound.
Release the carbonator button to allow the excess pressure to escape.
Carefully unscrew the bottle from the soda maker and enjoy your freshly carbonated water.

Individually-adjusted fizziness

With the BRITA sodaONE soda maker, you can individually adjust the fizziness of your water.
A short press of the carbonator button (approx. 1 second) will give you slightly fizzy water.
For medium fizziness, hold the button down for approx. 2 seconds.
For extra-fizzy water, keep the carbonator button pressed down until you can hear a clear buzzing sound (approx. 3 seconds).
By repeating this procedure you can add even more fizziness to your water.

Cleaning the sodaONE soda maker and the bottle

To ensure your soda maker gives you years of satisfaction, regular cleaning of the carbonator and the bottle is recommended.
Clean using only mild dishwashing liquid, lukewarm water, and, if necessary, a bottle brush.
Before using the brush, make sure it is suitable for cleaning plastic bottles and will not leave any scratches.
The bottle is not designed to withstand high temperatures (over +40° Celsius), which means it is not dishwasher safe.
As a result of the carbonation process, excess water may accumulate in the drip tray.
Please ensure the drip tray is regularly emptied and cleaned.

Troubleshooting

Problem	Potential solution
a small amount of CO2, or none at all, reaches the water bottle.	Make sure

that you fully press the carbonator button.
Keep the carbonator button pressed down until you hear a clear buzzing sound (2-3 seconds). Do not release the button until you hear the buzzing sound.
Check if the CO2 cylinder is properly screwed in.
The cylinder has run out of CO2 and needs to be replaced
Droplets of water are visible on the cylinder slot.| Try to screw in the CO2 cylinder slightly more tightly.
CO2 is escaping, but I am not pressing the carbonator button.| Remove the cylinder. Check if there is a black rubber gasket inside the cylinder bracket and if it is properly centered.
If the rubber gasket is missing, please contact BRITA customer service.
The cylinder gets extremely cold / freezes up.

Important information

Disposal

The packaging is made from recyclable material and can be disposed of with household waste-paper recycling.
Kindly dispose of the bottles in the general waste collection.
The soda maker can be disposed of as bulky waste, or at communal recycling centers.
BRITA CO2 cylinders can be disposed of at communal recycling centers.
Please comply with the respective local requirements.

100% satisfaction: the BRITA guarantee

At BRITA, we are convinced that you will be satisfied by the performance and quality of this product. But if you are not satisfied with this product, BRITA will take it back within 30 days of the date of purchase and refund the purchase price.
To do this, send the product with the sales receipt, the reason for the return, your full name, telephone number, and bank account details to the customer service address in your home country, which is stated on the back.

Exclusion of liability