B-TECH BT7553-050 Flat Screen Ceiling-Desk Mount with Tilt And Swivel Installation Guide
- June 9, 2024
- B-TECH
Table of Contents
**B-TECH BT7553-050 Flat Screen Ceiling-Desk Mount with Tilt And Swivel
**
FEATURES
- Designed to mount screens from the ceiling or a desktop
- Suitable for screens using VESA® fixings 75 x 75mm and 100 x 100mm
- Maximum load: 23kg
- Includes 50cm extension pole
- Ceiling drop: 767mm
- +/- 10° tilt adjustment and 360° swivel
- 360° screen rotation
- Allows screen to be positioned at almost any angle
- Integrated cable management
- Keyhole mounting for easy ‘hook-on’ installation
- Coverplate included for a clean appearance
- Supplied with security bolt for secure install
INSTALLATION TOOLS REQUIRED
-
Flathead & crosshead screwdriver
-
Drill
-
Drill bit
-
Pencil
-
Stud Finder (optional)
INSTALLATION SAFETY INSTRUCTIONS
CAUTION: This mount is intended for use only with the maximum weights
indicated.
Use with flat screen heavier than the maximum indicated may result in
instability causing possible injury.
Do not attempt to install this product until all instructions and warnings have been read and properly understood. Please keep these instructions for future reference. B-Tech International Limited, its distributors and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire.
General
B-Tech International Ltd recommends that a professional AV installer or other
suitably qualified person install this product. Great care must always be
taken during installation as most AV equipment is of a fragile nature,
possibly heavy and easily damaged if dropped.
If you do not fully understand the instructions or are not sure how to install
this product safely, then please consult a professional for advice and/or to
install this product for you. Failure to mount this product correctly may
cause serious injury or death both during installation and at any time
thereafter.
Do not mount any AV equipment that exceeds the specific weight limit of the product you are installing. This weight limit will be clearly stated on each product and its packaging and will vary from product to product.
Product location
Please pay careful attention to where this product is located. Some ceilings are not suitable for installation.
If located in a public or frequently populated area ensure that the product is out of the immediate reach of people. If any AV equipment is to be suspended over the likely path or location of people then great care should be taken to secure all parts of the installation from falling.
When drilling holes in ceilings it is essential to avoid contact with electrical cables and water or gas pipes contained within. Use of a good quality live wire detector and hidden object locator is therefore recommended. Only drill into structures when you are sure it is safe to do so.
Fixing hardware
It is highly recommended that all wall fixing screws be used where supplied and that the purpose of all other fixing hardware is fully understood. In some cases more AV equipment fixing hardware will be supplied to accommodate different models of equipment and set up configurations.
The installer must be satisfied that any supplied fixing hardware is suitable for each specific installation. If any fixing screws or included hardware are deemed not sufficient for a safe installation then please consult a professional or your local hardware store.
Hazard limitation
When routing cables take advantage of any built in cable management features
that the product might provide and ensure that all cables are tidy and secure.
Check to see that any moving aspect of the product can do so unhindered by any
cabling.
Some products have moving parts and the potential to cause injury through the
crushing or trapping of fingers or other body parts.
Particular attention to the nature of moving parts is required especially when
assembling installing and adjusting during set up.
Immediately after installations double-check that the work done is safe and secure. Doublecheck all necessary fixings are present and are of ample tightness.
It is recommended that periodic inspections of the product and its fixing points are made as frequently as possible to ensure that safety is maintained. If in doubt consult a professional AV installer or other suitably qualified person.
BT7553-050 PARTS LIST
| REF | PART NAME | QTY |
|---|---|---|
| 1 | CEILING MOUNT | 1 |
| 2 | EXTENSION POLE | 1 |
| 3 | FLAT SCREEN MOUNT | 1 |
| 4 | M8 x 60mm SCREW | 2 |
| 5 | M10 x 10mm GRUB SCREW | 4 |
| 6 | 5mm ALLEN KEY (FOR PARTS 4 & 5) | 1 |
| 7 | S13mm SOCKET WRENCH | 1 |
| INTERFACE KIT | ||
| 8 | M4 x 12mm SCREW | 4 |
INSTALLATION INSTRUCTIONS
-
Fix ceiling mount (Part 1) to the ceiling.
-
Attach the flat screen mount (Part 3) onto the extension pole (Part 2). Fit the M8 x 60mm screw (Part 4) and M10 x 10mm grub screws (Part 5) using the provided 5mm Allen key (Part 6).
-
Attach the flat screen mount and extension pole (Parts 2 & 3) to the ceiling mount (Part 1) using the M8 x 60mm screw (Part 4) and M10 x 10mm grub screws (Part 5).
DESKTOP EXAMPLE INSTALLATION
-
Mount the screen using the keyole fixings (suitable for screens with VESA 75 x 75mm or 100 x 100mm fixings). Insert halfway 2pcs M4 x 12mm screws (Part 8) into the upper VESA fixings on rear of screen with 6mm overhanging.
Mount screen onto VESA plate (Part 3). This procedure may require 2 persons.
-
Attach the remaining 2pcs M4 x 12mm screws into the lower VESA fixings holes of the screen and then tighten all screws, securing screen to mount.
-
If required, position the angle of the screen by adjusting the mount tension using the supplied S13mm socket wrench (Part 7) to adjust resistance.
Clockwise to increase tension
Counter-clockwise to decrease tension.
BT7553-‐050 PRODUCT
DIMENSIONS
THESE INSTRUCTIONS ARE INTENDED AS A GUIDE ONLY AND B- TECH ACCEPTS NO
LIABILITY FOR THE ACCURACY OF THE INFORMATION CONTAINED IN THIS DOCUMENT.
CUSTOMER SERVICE
B-TECH AUDIO VIDEO MOUNTS
HEAD OFFICE
B–Tech International Limited
Bennett House, Long March, Daventry, Northants., NN11 4NR, UK
Email: [email protected]
©2014 B–Tech International Limited. All rights reserved.
B–Tech Audio Video Mounts is a division of B–Tech International Limited.
B–Tech & Better By Design are registered trademarks of B–Tech International
Limited.
All other brands and product names are trademarks of their respective owners.
Photographs are for illustrative purposes only. E&OE.
AMA–BT7553–050–V1–0814–BTECH