SHOW B-2000.2 Switching Power Professional Amplifier User Manual

SHOW B-2000.2 Switching Power Professional Amplifier

SAFETY-RELATED SYMBOLS

• The symbol is used to indicate that some hazardous live terminals are involved within this apparatus, even under normal operating conditions.
• The symbol is used in the service documentation to indicate that a specific component shall be only replaced by the component specified in that Documentation for safety reasons.
• Protective grounding terminal.
• Alternating current /voltage.
• Hazardous live

ON : Denotes the apparatus turns on.
OFF : Denotes the apparatus turns off, because of using the single pole switch, be sure to unplug the AC power to prevent any electric shock before you proceed your service.
WARNING: Describes precautions that should be observed to prevent the danger of injury or death to the user.

Disposing of this product should not be placed in municipal waste and should be a separate collection.

CAUTION: Describes precautions that should be observed to prevent danger to the apparatus.

WARNING

• Power Supply Ensure the source voltage matches the voltage of the power supply before turning ON the apparatus.
• To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
  Do not use this apparatus near water. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not block any ventilation openings. No naked flame sources, such as lighted candles, should be placed on the apparatus.

IMPORTANT SAFETY INSTRUCTIONS

• Read these instructions.
• Follow all instructions.
• Keep these instructions.
• Heed all warnings.
• Only use attachments/accessories specified by the manufacturer.

Power Cord and Plug

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Cleaning

When the apparatus needs cleaning, you can blow off the dust from the apparatus with a blower or clean it with a rag, etc. Don’t use solvents such as benzol, alcohol, or other fluids with very strong volatility and flammability for cleaning the apparatus body. Clean only with a dry cloth.

Servicing

Refer all servicing to qualified personnel. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so .
Servicing is required when the apparatus has been damaged in any way, such as a power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. The mains plug is used as the disconnect device, the disconnect device shall remain readily operable.

INTRODUCTION

B-2000.2 switching power professional Amplifier is designed for professional use on stag e. The high-quality components and the carefully designed circuits ensure excellent audio performance and an extremely linear frequency response. In fact, the switching technology offers, together with an increased efficiency and a better control of heat dissipation than conventional power supply systems, a drastic reduction of dimensions and weight, for easier transportation and installation. This Amplifier guarantees total reliability and trouble-free use even in the most demanding conditions. We believe the B-2000.2 will provide a perfect performance, what you get is unprecedented performance at an incredibly attractive price.

Features:

• High current switching power allows high power output with low noise and low distortion
• Substantial protection circuitry like a thermal, short circuit, output DC offset, power on/off muting, and Therefore protection
• Built-in limiter
• Balanced XLR-TRS combo input jack
• Speakon output connectors
• Front-mounted gain controls for easy access
• Signal, Clip protect, Parallel mode, and Power LED indicators to monitor performance.

CONTROL ELEMENTS

FRONT PANEL

1. Power Switch
   It switches ON/OFF the unit’s main power(soft start)

2. Level Control
   These volume controls allow you to adjust the volume level.

3. Power LED
   The Power LED lights up when the amplifier is powered ON.

4. Signal LED
   These green LEDs light up when the respective channel’s output signal passes through.

5. Protection LED
   In normal operation, the LED will not illume; If the LED is red, it means the unit is in heat protection, and no sound is output. The speaker system is actually disconnected from the amplifier outputs when this LED is red, the temperature must be lowered by better ventilation and decrease the signal level, etc. if the problem is corrected, the protection systems deactivate automatically, and nor mal amplifier operation is resumed.

6. Clip LED
   This red LED lights up when the input signal is too strong. it is time to reduce the input level until clip LED is turned off.

7. Air Intake Vents
   B-2000.2 employs a variable-speed internal cooling fan to intake the air through the front grill to keep it running cool even under extreme operating conditions. Please keep these vents clear and free from obstruction at all times to insure proper cooling.

REAR PANEL

1. Breaker
   This switch works as a fuse to protect the unit from damage. When the unit is overloaded or the temperature inside the unit is too high, this pushing-button will spring up and break the power supply. The power supply will be restored by pushing this switch down again.

2. AC Input
   Use it to connect your B-2000.2 to the supplied AC cord.

3. Channel A XLR/TRS Input
   This XLR jack will accept any balanced or unbalanced low impedance line level source through a three-pin XLR plug. The wiring for the plug is as follows: Pin1=Ground, Pin2=Signal+, Pin3= Signal-.
   Channel B XLR/TRS Input
   This XLR jack will accept any balanced or unbalanced low impedance line level source by means of a three-pin XLR plug.

4. Signal Smart Switch
   Use this switch to select the operating mode of the amplifier. The switch functions as follows: STEREO: input A to CH A amp, input B to CH B amp;
   PARALLEL: input from channel A/B, both CHA and CHB will output signal.

5. Channel A Speakon NL-4R
   Connect the amplifier to your speakers using these speakon jacks.

6. Channel B Speakon NL-4R
   Connect the amplifier to your speakers using these speakon jacks.

7. Exhaust Vents
   Air is drawn from the front grilles, flown through the unit and heat sink, and then exhausted via the rear vents. Do not block or impede the air flow through these vents and keep the vent areas free of foreign materials.

APPLICATIONS

Stereo Operation

B-2000.2 can be used in the stereo mode as two separate B-2000.2 watts units, each capable of driving loads down to 4 ohms. Each channel operates independently and has its own input connectors, sensitivity level controls, signal indicator LEDs, automatic limiters, fault protection circuitry, power amp, and speaker outputs. In the stereo mode, the signal smart switch must be set to the stereo position. One application of the stereo mode uses one channel of the amplifier for the left-house speakers and the other channel for the right. The mixing board channels can be panned left or right according to the position of the instruments on the stage. T his approach provides a more accurate reproduction of the live performance.

Parallel Operation

If many speakers must be driven from the same signal, you can operate on a PARALLEL way: input from channel A, output the same signal from channels A and B which can drive solely two 8 ohms speakers. The signal smart switch must be set to a parallel position.

WIRING CONNECTIONS

BLOCK DIAGRAM

TECHNICAL SPECIFICATIONS

Stereo Mode

(Both Channels Drive)

| 2 ohms(EIAJ)| 3000W2
4 ohms(RMS)| 2000W2
8 ohms(RMS)| 1200W*2
Electrical Specification
Input Sensitivity (Limit Off)| 0.9-1.1V(0+/-1dBv)
Input Impedance| 20k ohms balanced or 10k Ohms unbalanced
Frequency Response

(at -10dB Rated Output Power 8 )

| 20Hz ~ 20KHz(+0/-1dB)
Voltage Gain| 40+/-0.5dB
THD+N

(Ref.1K 1/8 Rated Power,A-Weighted)

| <0.1%
S/N rate

(Ref. Rated Power, A-Weighted)

| >100dB
Crosstalk (Below Rated Power)| >70dB
Damping Factor(1K 8 ohms)| >200
Power/Output Circuitry| Switching Power Class D
General Specifications
Protections| Full short circuit, open circuit, thermal, ultrasonic and RF protection stable into reactive or mismatched loads, turn ON/OFF, muting, tried crowbar.
Controls| Front: AC switch(soft-start), Input level control for each channel Rear: stereo/ parallel/ selector.
Indicators| SIGNAL: 2 green LED          CLIP: 4 red LED         POWER: 2 green LED PROTECTION: 2 red LED
Connectors| INPUT : Balanced XLR-TRS combo input jacks OUTPUT:speak-on jacks
Power Supply| 110-120V or 220-240V~50/60Hz
Dimensions(mm)| 483(W)360(D)88(H)
Weight| 5kg

IMPORTANT!

Please read this manual carefully before operating this unit for the first time.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>