PORTOR LIGHTING PT-DLS-R-FR-6I-15W Round LED Slim Recessed Downlight Instruction Manual

PORTOR LIGHTING PT-DLS-R-FR-6I-15W Round LED Slim Recessed Downlight

Product Information

Specifications

• Series: PT-DLS-R-FR
• Model Variants: PT-DLS-R-FR-6I-15W / PT-DLS-R-FR-4I-12W
• Installation: Indoor only
• Power Supply: Consult a qualified electrician Fixture Mounting Hole Cut Sizes: 4 round and square: 4-1/4 (108 mm), 6 round and square: 6-1/4 (158.75 mm)
• Website:www.portorlighting.com

Product Usage Instructions

Installation Instructions

1. Read all instructions before installing fixtures. Retain for future reference.
2. Ensure the fixture is wired under local electrical codes and ordinances. All work should be done by a qualified electrician.
3. Make certain power is off from the electrical panel before starting installation or attempting any maintenance.

Assembly Instructions

1. Disconnect electrical power before installing or servicing any part of this fixture.
2. Locate a suitable position to place the fixture and open it according to the cut-hole dimensions mentioned in the hole-cut table.
3. Run electrical wire from the switch (power supply) through the mounting hole using NMD90 Romex or BX cable.

Tools Required

• Safety goggles
• Drill saw/saw
• Measuring tape
• Electrical wiring (use type and gauge suitable for application to connect the fixtures)
• Power supply

Driver Wiring

1. Open the hardwire box swing cover and remove the appropriate knockout(s).
2. Insert the electrical supply cable through the knockout and secure it with a cable connector (sold separately).
3. Using wire nuts, connect the green ground wire of the cable to the green wire on the box. Connect the white wire of the cable to the white wire of the box. Connect the black wire of the cable to the black wire of the box.
4. Place all wiring and connections back into the box and close the cover.
5. Insert the hardwire box through the mounting hole.

Note: For new construction applications, the hardwire box should be firmly secured to studs, joists, or similar fixed structural units. Remodel applications do not require the hardwire box to be firmly secured after the mounting plates, studs, joists, or structural units have been concealed.

Fixture Installation

1. Connect the fixture to the hardwire box by inserting and twisting the male/female connectors. Select the desired Color Temperature.
2. Push the spring-loaded clips on the fixture upwards and insert the fixture base into the mounting hole. Release the clips, and the fixture will be pulled flush to the ceiling.
3. Once assembly is complete, turn on the power to confirm that the fixture is working properly.

FAQ:

Q: Can I install the fixture outdoors?

• A: No, the fixture is designed for indoor installation only.

Q: What type of cable should I use to run the electrical wire from the switch to the mounting hole?

• A: Use NMD90 Romex or BX cable for running the electrical wire.

Q: Do I need to secure the hardwire box for remodel applications?

• A: No, the hardwire box does not need to be firmly secured for remodel applications once the mounting plates, studs, joists, or structural units have been concealed.

Q: How do I connect the fixture to the hardwire box?

• A: Insert and twist the male/female connectors to connect the fixture to the hardwire box.

Q: How do I ensure the fixture is flush with the ceiling?

• A: Push the spring-loaded clips on the fixture upwards, insert the fixture base into the mounting hole, and then release the clips. The fixture will be pulled flush to the ceiling.

Q: What should I do if the fixture is not working after assembly?

• A: Check the power supply and connections to ensure they are properly installed. If the issue persists, consult a qualified electrician.
• IMPORTANT READ ALL INSTRUCTIONS BEFORE INSTALLING FIXTURES. RETAIN FOR FUTURE REFERENCE.
• SAFETY FOR YOUR SAFETY, THIS FIXTURE MUST BE WIRED IN ACCORDANCE WITH LOCAL ELECTRICAL CODES AND ORDINANCES. ALL WORK SHOULD BE DONE BY A QUALIFIED ELECTRICIAN.
• WARNING MAKE CERTAIN POWER IS OFF FROM THE ELECTRICAL PANEL BEFORE STARTING INSTALLATION OR ATTEMPTING ANY MAINTENANCE. INDOOR INSTALLATION ONLY.

ASSEMBLY INSTRUCTIONS

1. PREPARING FOR INSTALLATION: DISCONNECT ELECTRICAL POWER BEFORE INSTALLING OR SERVICING ANY PART OF THIS FIXTURE.
2. LOCATE A SUITABLE POSITION TO PLATE THE FIXTURE AND OPEN BY THE CUT-HOLE DIMENSIONS (REFER TO HOLE CUT TABLE FOR APPROPRIATE SIZE).
3. RUN ELECTRICAL WIRE FROM THE SWITCH (POWER SUPPLY) THROUGH THE MOUNTING HOLE-USE NMD90 ROMEX OR BX CABLE.

TOOLS REQUIRED

INSTALLATION

( CONSULT A QUALIFIED ELECTRICIAN BEFORE INSTALLING )

DRIVER WIRING

1. Open the hardwire box swing cover and remove the appropriate knockout (s).
2. Insert the electrical supply cable through the knockout and secure it with a cable connector (sold separately).
3. Using wire nuts, connect the green ground wire of the cable to the green wire on the box. Connect the white wire of the cable to the white wire of the box. Connect the black wire of the cable to the black wire of the box. (Figure 1)
4. Place all wiring and connections back into the box and close the cover.
5. Insert the hardwire box through the mounting hole. (Figure 2)
   NEW CONSTRUCTION APPLICATIONS: Hardwire box shall be firmly secured to studs, joists, or similar fixed structural units. REMODEL APPLICATIONS: Do not require the hardwire box to be firmly secured after the mounting plates, studs, joists, or structural units have been concealed.

FIXTURE INSTALLATION

1. Connect the fixture to the hardwire box by inserting and twisting the male/female connectors. Select the desired Color Temperature. (Figure 3)
2. Push spring-loaded clips on the fixture upwards and insert the fixture base into the mounting hole. Release the clips and the fixture will be pulled flush to the ceiling. (Figure 4)
3. Once assembly is complete, turn on the power to confirm the fixture is working properly.

HOLE CUT SIZE:

• 4” round and square: 4-1/4” (108 mm)
• 6” round and square: 6-1/4” (158.75 mm)
• www.portorlighting.com Specification subject to change without notice

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>