Naked NKD-pH Squeeze Tube Instruction Manual
- June 15, 2024
- Naked
Table of Contents
Naked NKD-pH Squeeze Tube
Product Information
Specifications
- Product Name: NKD-pH Squeeze Tube
- Power Source: Piggyback power cord
- Material: Clear PVC tubes
- Colour: Black
- Includes: Silicone Lubricant sachet
Product Usage Instructions
Important Safety Precautions
- All equipment is designed to be plug-and-play; however, to reduce the risk of accidents or incidents, service on the unit is recommended to be performed by a qualified pool service professional and not operated by children under 18 years of age.
- Wear protective equipment and do not inhale the fumes. The Silicone Lubricant provided is not edible.
Installation Steps
- Step 1: Disconnect the power by removing the NKD-pH piggyback power cord from the power source it is plugged into.
- Step 2: Remove both clear PVC tubes from the bottom of the NKD-pH pump by unscrewing the black tube nuts.
- Step 3: Place your thumb under the 3 dots on the bottom of the charcoal cover and pull it towards you to remove. Unscrew the 3 screws and remove the clear acrylic cover and put them aside as you will require these later. Take a photo of the 3 rollers and the squeeze tube as seen to the right, so you can see how the replacement will fit once completed.
- Step 4: Remove the existing squeeze tube (black tube with lubricant), complete with the two black barb adaptors and tube nuts on the bottom, by gently pulling the left side tube barb adaptor towards you and lifting from left to right. Scan the QR code below to see our video instructions and further details.
- Step 5: We recommend using disposable gloves for this step. Lubricate the new squeeze tube with the lubricant sachet provided in the kit. Apply the lubricant to the bottom half of the squeeze tube (white writing), this will make it easier when installing the tube.
- Step 6: Starting from the left side, fit the left barb adaptor correctly in the slot. Press the squeeze tube between the roller blocks, working from left to right in a clockwise direction. Use two fingers to slip the squeeze tube between each roller. Note: The clear acrylic cover will not fit properly if the barb adaptors do not sit flat.
- Step 7: Refit the clear acrylic cover using the original 3 screws and clip the charcoal cover back on.
- Step 8: Reconnect the clear PVC tubes to the bottom barb adaptors and tighten them with the black tube nuts.
- Step 9: Reconnect the power cord of the NKD-pH controller to the power source.
- Step 10: Prime the system using the procedure in the NKD-pH Installation & Startup Guide.
FAQ
- Q: Can children under 18 years of age operate this product?
- A: No, it is recommended that this product is not operated by children under 18 years of age. Service should be performed by a qualified pool service professional.
- Q: Is the Silicone Lubricant edible?
- A: No, the Silicone Lubricant provided is not edible.
INSTRUCTIONS FOR REPLACING THE NKD-pH SQUEEZE TUBE
IMPORTANT – PLEASE READ
All equipment is designed to be plug-and-play however, to reduce the risk of accidents or incidents, service on the unit is recommended to be performed by a qualified pool service professional and not operated by children under 18 years of age. Wear protective equipment and do not inhale the fumes. The Silicone Lubricant provided is not edible.
INSTALLATION STEPS
STEP 1
- Disconnect the power by removing the NKD-pH piggyback power cord from the power source it is plugged into.
STEP 2
- Remove both clear PVC tubes from the bottom of the NKD-pH pump by unscrewing the black tube nuts.
STEP 3
- Place your thumb under the 3 dots on the bottom of the charcoal cover and pull it towards you to remove. Unscrew the 3 screws and remove the clear acrylic cover and put them aside as you will require these later. Take a photo of the 3 rollers and the squeeze tube as seen to the right, so you can see how the replacement will once completed.
STEP 4
- Remove the existing squeeze tube (black tube with lubricant), complete with the two black barb adaptors and tube nuts on the bottom, by gently pulling the left side tube barb adaptor towards you and lifting from left to right. Scan the QR code below to see our video instructions and further details.
STEP 5
- We recommend using disposable gloves for this step. Lubricate the new squeeze tube with the lubricant sachet provided in the kit. Apply the lubricant to the bottom half of the squeeze tube (white writing), this will make it easier when installing the tube.
STEP 6
- Starting from the left side. Fit the left barb adaptor correctly in the slot. Press the squeeze tube between the roller blocks, working from left to right in a clockwise direction. Use two fingers to slip the squeeze tube between each roller.
NOTE: The clear acrylic cover will not work properly if the barb adaptors do not sit.
STEP 7
- Refit the clear acrylic cover using the original 3 screws and clip the charcoal cover back on.
STEP 8
- Reconnect the clear PVC tubes to the bottom barb adaptors and tighten them with the black tube nuts.
STEP 9
- Reconnect the power cord of the NKD-pH controller to the power source.
STEP 10
- Prime the system using the procedure in the NKD-pH Installation & Startup Guide.
Specifications are subject to change without notice. Whilst every care was taken in preparation of this document, Naked Pools accepts no responsibility for the accuracy of information supplied. The contents of these instructions are the exclusive copyright of Naked Pools and may not be reproduced without written permission. © 2023.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>