PIXIE SMC3BTAS Multifunction Remote Control Button Instruction Manual
- June 15, 2024
- PIXIE
Table of Contents
Installation Instructions
Multifunction
Remote Control Button G3
SMC3BTAS
SMC3BTAS Multifunction Remote Control Button
WARNING
This product contains lithium coin battery
KEEP BATTERIES OUT OF REACH OF CHILDREN
**** Swallowing can cause severe or fatal injuries within 2 hours. Seek
immediate medical attention if swallowed.
Product Introduction
The PIXIE Multifunction Remote Control Button is the 3rd generation
multifunction remote control button, that is portable and powered by coin
battery. Without the need of running wires, this product brings huge
flexibility for the application.
1.1 Product Features
- Coin battery powered, portable without worrying wiring availability
- LED indicator colour selectable – blue or amber
- PIXIE Multifunction Remote Control button Gen 3, can pair with a master device, a group or scenes
1.2 Product Parts
Specifications and Capabilities
Product Description| Model NO.| Battery| Colour|
Dimensions L x W x H (mm)| Weight (g)
---|---|---|---|---|---
PIXIE Multifunction Remote Control Mech| SMC3BTAS| CR2032 * 1| White| 50 x 50
x 13| 16
Product Application| Interior residential or commercial| Product Installation|
Portable
---|---|---|---
Operating Ambient Temperature| 0℃- 40℃| Storage Ambient Temperature| 0℃- 60℃
Operating Humidity| 0-85% RH, NC| Storage Humidity| 0-85% RH, NC
IP Rating| IP20|
Installation process
3.1 – Before installation, for optimum signal communication, the maximum
distance between a PIXIE device and the controlled device is 15 metres.
3.2 – Launch pairing mode for PIXIE Master device
3.3 – Launch paring mode of SMC3BTAS within 30 seconds.
Note: If the paired PIXIE product changes HOME setup in the PIXIE Apps or
reset to factory, the pairing process will need to be repeated.
Operations
4.1 Setting operations
Operation | **Function** | **LED Indicator** | **Remark** |
---|---|---|---|
4 Clicks | Enter pairing mode, the mode lasts 10 seconds | Quickly flash in blue | |
for 10 seconds | – Can pair with a PIXIE master device, a group or two scenes |
– After a successful pairing, pairing mode will end.
Pressing the button during pairing mode will cancel and exit pairing mode
– LED indicator will flash twice, and stay solid blue for 2 seconds to
indicate the pairing is successful
5 Clicks| Change the LED indicator color| _| Toggle LED indicator colour
selectable – blue or amber
9 Clicks| Reset the product to factory default| Slowly flash ble for 3
seconds| All the previous pairing will be cleared after a successful reset
4.2 Control operations – paired with a master device
Operations when configured to control a device
Paired device
Operation| PIXIE
Smart Dimmer| PIXIE
Smart RGB Strip, RGB Strip Controller| PIXIE
Smart Single Color Strip, Single Color Strip Controller
---|---|---|---
1 Click| Turn ON/OFF.
When turning the light on, it will work on the last used brightness setting|
Turn ON/OFF.
When turning the light on, it will work on the last used brightness setting|
Turn ON/OFF.
When turning the light on, it will work on the last used brightness setting
2 Clicks| Shortcut to the maximum brightness| Shortcut to the maximum
brightness| Shortcut to the maximum brightness
3 Clicks| Switch to the next color temperature, which circulates in Warm
White->Cool White-> Daylight. For S9842 downlight only.| Switch to the next
color. Color circulates in White->Red->Green->Blue.| NA
Long Press| When the light is on, long press the button to dim up or down,
release the button to stop.
When the light is off, long press the button to turn on the light at minimum
brightness and increase brightness, release the button to stop.| When the
light is on, long press the button to dim up or down, release the button to
stop.
When the light is off, long press the button to turn on the light at minimum
brightness and increase brightness, release the button to stop.| When the
light is on, long press the button to dim up or down, release the button to
stop.
When the light is off, long press the button to turn on the light at minimum
brightness and increase brightness, release the button to stop.
4.3 Control operations – paired with a group
Operations when configured to control a group
Operation | Result | Remark |
---|---|---|
1 Click | Turn ON/OFF the Group | NA |
2 Clicks | Shortcut to the maximum brightness | Dimmable product group only |
3 Clicks | Switch colour/colour temperature | Subject to the product group |
functionality
Long Press| Switch colour/colour temperature| Dimmable product group only
4.4 Control operations – paired with scenes
Operations when configured to control scenes
Operation | Result |
---|---|
1 Click | Activate scene 1 |
2 Clicks | Activate scene 2 |
Battery replacement
When the battery is low, the operation will not work properly. Please follow
the steps below to replace the battery.
5.1 – Locate the tab as indicated in the image, use screwdriver to slightly
push the tab a bit farther away from the body.
5.2 – Meanwhile, rotate the back cover anticlockwise to remove it.
5.3 – Remove the battery
5.4 – Insert a new CR2032 lithium 3V coin battery with positive side facing up
5.5 – Replace the cover to align with the slot, rotate the cover clockwise
until it stops. warning: The battery might cause injury to small children.
Keep away from small children.
Scan QR code or go to App store (IOS) or Google Play (Android) to download the
free PIXIE app to your smart phone.
IOS: Requires IOS 6.0 or later. Compatible with iPhone, iPad and iPad touch
Android: Requires Android 4.4 or above, devices must support Bluetooth 4.0
Specifications above are for reference only and may vary without prior notice.
https://www.pixie.app/download/pixie/
https://www.pixie.app/download/pixieplus/
Warranty – In accordance with SAL’s standard terms and conditions of
sale, SAL warrant this product to be free from defects in materials and or
workmanship for a period as stated below for goods not subject to incorrect
installation, maintenance, operation, mishandling, environmental, unauthorised
modifications or electrical operating conditions outside the nominated product
specification as detailed in these installation instructions. The benefits to
you given by this warranty are in addition to other rights and remedies you
have under law. Our goods come with guarantees that cannot be excluded under
the Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a
major failure.
Warranty term – Residential usage (12) months, Commercial usage (12)
months, Replaceable lamps (where supplied) (12) months and batteries where
supplied (12) months from date of purchase.
How to make a claim?
Step #1 – Within 30 days of the fault discovery, please contact the
original place of the SAL product purchase during standard (local) business
hours, with the following information (a) proof of purchase (b) description
and quantity of the claimed fault (c) address of installation. (d) operating
hours of the product.
Step #2 – It is then the responsibility of the original place of product
purchase to report the matter to SAL aftersales;
NSW | ACT| SAL National Pty Ltd, 40 Biloela Street Villawood NSW 2163| | P #
02 9723 3099
---|---|---
QLD| SAL National Pty Ltd, 36 Whitelaw Place Richlands QLD 4077| | P # 07 3879
5999
VICT | TAS | SA | NT| SAL National Pty Ltd, 46-48 Keys Road Moorabbin Victoria
3189| | P # 03 9532 3168
WA| SAL National Pty Ltd, 29 Beringarra Av Malaga WA 6090| | P # 08 9248 7458
Step #3 – Upon review of your claim and if the product is required to be
returned to SAL for technical evaluation, then at the owners expense the
product must be returned to SAL as per the above nominated locations.
Step #4 – Pending the evaluation, the claim will be validated resulting
in the product being repaired or replaced with the same or best equivalent
product at the discretion of SAL, or rejected if the product fault was found
to be caused by conditions beyond the responsibility of SAL warranty
obligations. Consideration of installation, product removal, return freight
and or testing fees are not the responsibility of SAL.
- The product wireframe drawings in this document are intended for illustration purposes only and may differ from the final physical product.
- The installation instruction is subject to change without prior notice.
PIXIE is a trademark of SAL National Pty Ltd.
COPYRIGHT © 2022 This document is copyright by SAL National Pty Ltd. Except as
permitted under the relevant law, no part of this application note may be
reproduced by any process without written permission of and acknowledgment to
SAL National.
DISCLAIMER: SAL National reserves the right to alter the specifications,
designs or other features of any items and to discontinue any items at any
time without notice and without liability. While every effort is made to
ensure that all information in this application note is correct, no warranty
of accuracy is given and SAL National shall not be liable for any error.
TRADEMARKS: The identified trademarks and copyrights are the property of SAL
National ty Ltd unless otherwise noted.
Contact Information
SAL National Pty Ltd.
Web: www.sal.net.au
ABN: 21 633 189 474
All Enquiries:
+61 2 9723 3099
pixiesupport@sal.net.au
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>