EUROTRONIC SPARmatic Comet Electronic Energy Saving Regulator Instruction Manual

EUROTRONIC SPARmatic Comet Electronic Energy Saving Regulator

Product Information

Specifications

• Model: Sparmatic Comet
• Version: 2023.11
• Operating Instructions: Version 1.1 / EN

Product Usage Instructions

Safety Information
Before using your Sparmatic Comet, please read and observe the following safety information:

• Observe all safety regulations and local laws and regulations.
• Only use the Sparmatic Comet as described in the operating instructions.
• Pay attention to all warnings and cautions mentioned in the operating instructions.

Scope of Delivery
The Sparmatic Comet package includes the following items:

• RAV pin*
• RAVL
• Screw for adapter
• RAV Sparmatic Comet
• *When using the RAV adapter, the RAV pin is required to extend the valve plunger.

Overview
The Sparmatic Comet allows you to set your heating and economy times easily. You can choose to set it manually or use the Progmatic programming stick for quick and easy transfer of settings to all energy-saving controllers in your home. For more information on the Progmatic programming sticks, visit www.eurotronic.org .

Controls and Display Elements
The Sparmatic Comet features the following controls and display elements: [Insert controls and display elements information here]

FAQ

• Q: How do I install the Sparmatic Comet?
  A: Please refer to the installation instructions provided in the operating manual.

• Q: Can I use the Sparmatic Comet with other energy-saving controllers?
  A: Yes, you can use the Progmatic programming stick to transfer your settings to all compatible energy-saving controllers in your home.

• Q: Is the Sparmatic Comet compatible with all heating systems?
  A: The Sparmatic Comet is designed to work with most common heating systems. However, it is recommended to check the compatibility with your specific heating system before installation.

Sparmatic Comet  OPERATING INSTRUCTIONS

LEGAL NOTICE

• Operating Instructions
  Sparmatic Comet Electronic Energy-Saving Controller

• Manufacturer
  EUROtronic Technology GmbH

• Südweg 1
  36396 Steinau-Ulmbach

• Germany
  www.eurotronic.org

• Publisher
  Ingenieurbüro FORMAT GmbH

• Ebertstraße 80
  26382 Wilhelmshaven

• Germany
  www.format-docu.de

Operating Instructions

• Status 2023.11
• Version 1.1 / EN

Legal Information
All brand names and trademarks mentioned in this document and, where applicable, protected by third-party rights, are subject without restriction to the provisions of the applicable trademark law and the ownership rights of the respective registered owners. Comply with all local and regional laws and regulations as well as the safety regulations referred to in this document.

Copyright Notice

• The contents of this document are protected by copyright.
• The disclosure, transfer and any other distribution of the contents of this document to third parties, the making of copies, transcripts and other reproductions as well as utilization and any other use are prohibited – even in part – without the prior, express and written consent of the author.
• © 2023 All rights reserved.

SAFETY INFORMATION

• In addition to the safety information in these operating instructions, all other available sources must also be observed.
• The areas of use defined in the written explanations of the proper use must be observed.

DEPICTION OF WARNINGS
The warnings used in these operating instructions have the following meaning:

WARNINGS
When operating your Sparmatic Comet and its components, hazards may occur that can be avoided by observing the following warnings.

CAUTION!
Serious risk of injury caused by exploding batteries!
Improper handling of batteries can lead to an explosion.

• Do not heat batteries and do not throw batteries into open fire.
• Do not place batteries in direct sunlight.
• Protect batteries from excessive heat.
• Do not short-circuit the batteries.
• Never attempt to charge non-rechargeable batteries.
• Never dismantle batteries.
• Do not use new and used batteries together.
• When inserting the batteries, observe the correct polarity (+/-).
• Before inserting the batteries, clean the batteries and the contacts in the thermostat.

CAUTION!: Serious risk of injury caused by chemical burns!
Leaking battery acid can cause burns.

• Avoid contact of battery acid with skin, eyes and mucous membranes.
• In case of contact with battery acid, immediately rinse the affected areas with plenty of clean water and consult a doctor.

CAUTION!: Serious risk of injury caused by malfunction!
Malfunctions can lead to injuries.

• NEVER carry out repairs to your Sparmatic Comet yourself.
• Do not open your Sparmatic Comet.
• Do not carry out any modifications or conversions on your Sparmatic Comet.
• In the event of an error, contact Customer Service.

CAUTION!: Risk of fatal injury and accidents to infants and children!
The Sparmatic Comet and packaging material represent a risk of choking and suffocation.

• Never leave children unsupervised with your Sparmatic Comet or the packaging material. Children often underestimate the risks involved. Always keep children away from your Sparmatic Comet and the packaging material.
• Keep batteries out of reach of children. Should a battery be swallowed, seek medical attention immediately.
• Your Sparmatic Comet is not a toy.

IMPORTANT! Material damage and malfunction possible!
Your Sparmatic Comet can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been supervised or instructed in the safe use of your Sparmatic Comet and understand the hazards involved.

• Children may not play with your Sparmatic Comet.
• Cleaning and user maintenance must not be carried out by children without supervision.

IMPORTANT! Material damage and malfunction possible!
Environmental influences can affect the functions of your Sparmatic Comet.

• Keep your Sparmatic Comet away from direct sunlight.
• Only use your Sparmatic Comet in a dry, dust-free environment.

IMPORTANT! Material damage and malfunction possible!
Damaged components and/or malfunctions will prevent your Sparmatic Comet from functioning properly.
If material damage and/or malfunctions occur, contact the Customer Service of Eurotronic Technology GmbH.

SCOPE OF DELIVERY

Check the scope of delivery for completeness as well as visual and technical defects before putting your Sparmatic Comet into operation.

• 1× Sparmatic Comet
• 1× Operating Instructions
• 3× Adapter (Danfoss RA/RAV/RAVL)
• 1× Screw for adapter

IMPORTANT! Material damage and malfunction possible!
Damaged components and/or malfunctions will prevent your Sparmatic Comet from functioning properly.
If material damage and/or malfunctions occur, contact the Customer Service of Eurotronic Technology GmbH.

INFORMATION
The following drawings are for the purpose of illustration and are not necessarily to scale. EUROtronic Technology GmbH reserves the right to change the design or dimensions without prior notice.

*When using the RAV adapter, the RAV pin is required to extend the valve plunger.

OVERVIEW

• Thank you for choosing a product from EUROtronic Technology GmbH. Your Sparmatic Comet is a configurable energy-saving controller for the radiator featuring modern, simple operation. It automatically regulates your room temperature according to your specifications.
• Your Sparmatic Comet helps you to effectively reduce your heating costs.
• Development and production are 100% “Made in Germany”, which guarantees premium quality and technology. These operating instructions will help you to get your Sparmatic Comet up and running quickly and easily.

By the way…

• Are you already familiar with our Progmatic programming sticks?
• You can set your Sparmatic Comet manually or you can use the convenient Progmatic programming stick to transfer your individually set heating and economy times to all energy-saving controllers with programming port in your home in a matter of seconds!
• Detailed information on the Progmatic programming sticks is available at: www.eurotronic.org

PROPER USE

• Your Sparmatic Comet is used to regulate a radiator valve. This makes it possible to regulate the room temperature time-controlled. Your Sparmatic Comet moves a radiator valve to control the flow of heat into the radiator. It can be installed on all common radiator valves. Only use your Sparmatic Comet indoors.
• Any use other than that described in these operating instructions is not in accordance with the proper use and will result in the warranty being voided and exclusion of liability. It is forbidden to complete any unauthorised modifications, conversions and repairs. Your Sparmatic Comet is intended for private use only.

CONTROLS AND DISPLAY ELEMENTS

The following section describes the controls and display elements of your Sparmatic Comet.

1. Union nut
2. Heating times
3. Child safety lock active
4. Function symbols( )
5. button – Confirm
6. button – Timer function
7. Setting wheel
8. Battery compartment
9. button – Main menu/one menu back
10. AUTO or MANU mode active
11. Programming port*

INFORMATION
*The programming port is intended exclusively for connecting the Progmatic programming stick. Do not connect any other devices to the programming port of your Sparmatic Comet.

PUTTING INTO OPERATION

The following section describes the installation and initial operation of your Sparmatic Comet.

INSERTING BATTERIES
Before installation, insert batteries in your Sparmatic Comet.

1. Press the battery compartment cover upwards and remove it.

2. Insert two suitable batteries (1.5 V AA/LR6) as shown.
   Pay attention to the correct polarity and do not use rechargeable batteries!

3. Replace the battery compartment cover.

4. The battery compartment cover audibly clicks into place.

5. You have successfully inserted the batteries.

INFORMATION
After each battery change, stored heating programmes are retained. If necessary, check the date and time (see  Section 5.2 Setting date and time on Page 11).

INFORMATION
Note that your Sparmatic Comet is not in the installation mode after inserting the batteries. Set the date and time for this purpose (see  Section 5.2 Setting date and time on Page 11).

SETTING DATE AND TIME

During initial operation, the year flashes in the display after inserting the batteries

1. Set the year with the setting wheel and confirm with the  ok button.
2. Set the month with the setting wheel and confirm with the ok button.
3. Set the day with the setting wheel and confirm with the ok button.
4. Set the hour with the setting wheel and confirm with the ok button.
5. Set the minute with the setting wheel and confirm with the ok button.
6. You have set the date and time.
7. PrEP appears in the display.
8. The motor retracts completely to facilitate installation.
9. The display shows AdAP and your Sparmatic Comet is in the adaptation mode. Do not press any other button and continue with the installation.

INFORMATION
Your Sparmatic Comet automatically switches to summer and winter time. You can also set the date and time at a later time using the TIME menu item. Note that your Sparmatic Comet does not switch to the adaptation mode and the motor does not completely ramp up.

INSTALLING ON RADIATOR

• After you have set the time and date (see  Section 5.2 Setting date and time on Page 11), install your Sparmatic Comet on the desired radiator.
• The Sparmatic Comet can be installed on all known valve bodies (see adapter list at www.eurotronic.org/service/faq ).

CAUTION!: Burns caused by hot radiator valve!

• Touching can cause burns to the hand.
• Avoid contact of battery acid with skin, eyes and mucous membranes.
  • Allow the radiator to cool down before installing, removing or troubleshooting your Sparmatic Comet!

1. Open the current thermostatic head completely. Loosen the fastening and pull the thermostatic head off the radiator.
2. Optional: Select a suitable adapter from the scope of delivery. For additional information on the adapters, please see the Section 5.4 Adapter overview on Page 14.
3. Put your Sparmatic Comet on the radiator and turn the union nut clockwise.
4. You have successfully installed your Sparmatic Comet.
5. Following installation, start the adaptation, see  Section 5.5 Adapting Sparmatic Comet on Page 16.

INFORMATION
For later assembly, select the INST item in the menu with the setting wheel and confirm with the button. AdAP is shown in the display of your Sparmatic Comet. Only install your Sparmatic Comet in this position.

ADAPTER OVERVIEW
The following overview contains information about the valves and the required adapters. The adapters for Danfoss RAV, Danfoss RA and Danfoss RAVL are included with your Sparmatic Comet. When using the Danfoss RAV adapter, the RAV pin must be inserted on the valve plunger.

| | |
---|---|---|---
Valve| Thread dimension| Adapter
Heimeier| M30 x 1.5 mm| Not required
Junkers Landys+Gyr| M30 x 1.5 mm| Not required
MNG| M30 x 1.5 mm| Not required
Honeywell| M30 x 1.5 mm| Not required
Braukmann| M30 x 1.5 mm| Not required
Herz| M28 x 1.5 mm| Required; not in scope of delivery
Comap| M28 x 1.5 mm| Required; not in scope of delivery
Vaillant| 30.5 mm| Required; not in scope of delivery
Oventrop| M30 x 1.0 mm| Required; not in scope of delivery
Meges| M38 x 1.5 mm| Required; not in scope of delivery
Ondal| M38 x 1.5 mm| Required; not in scope of delivery
Giacomini| 22.6 mm| Required; not in scope of delivery
Rossweiner| M33 x 2.0 mm| Required; not in scope of delivery
Markaryd| M28 x 1.0 mm| Required; not in scope of delivery
Ista| M32 x 1.0 mm| Required; not in scope of delivery
Vama| M28 x 1.0 mm| Required; not in scope of delivery
Pettinaroli| M28 x 1.5 mm| Required; not in scope of delivery
T+A| M28 x 1.5 mm| Required; not in scope of delivery
Gampper 1/2/6| M20| Required; not in scope of delivery
Danfoss RA/RAV/RAVL| 25.5/30.5/30 mm| Included in scope of delivery

INFORMATION
Remove the connecting pieces of the plastic adapters completely (see illustration) before using one of the adapters included! For Danfoss RAV and Danfoss RA, use the screw and nut provided.

CAUTION!: Danger of becoming trapped between the adapter halves!
Carelessness when using adapters can lead to injuries.
Take care not to become trapped between the adapter halves during installation!

CAUTION!: Danger of being cut!
The adapters supplied and the plunger extension are connected by plastic bars. Fractures may be sharp-edged.
Be careful not to cut your fingers during installation!

• You can purchase further metal adapters for a fee from our partners. You will find an overview of the met-al adapters and corresponding ordering options under the following link:
  https://eurotronic.org/produkte/zubehoer/metalladapter/

• For assistance in identifying your valve, please refer to the “Adapter list” section under the following link: https://eurotronic.org/service/faq

ADAPTING SPARMATIC COMET
After successful installation, your Sparmatic Comet can begin with the adaptation. The prerequisite is that AdAP is shown in the display of your Sparmatic Comet.

1. Press the ok button.

Your Sparmatic Comet begins the adaptation process.
When adapting, your Sparmatic Comet adapts to the stroke of your lower valve section. For this purpose, the valve is opened and closed several times to detect the respective end points. The process may take a moment. After successful adaptation, your Sparmatic Comet switches to normal operation.

INFORMATION
If a new adaptation is necessary (e.g. if your radiator does not become cold in the OFF position), select the item AdAP in the menu and carry out the adaptation again.

If a problem occurs with your Sparmatic Comet, a new adaptation is necessary. Carry out the following steps for this purpose:

1. Open the battery compartment cover of your Sparmatic Comet.
2. Remove the batteries.
3. Wait for approx. 10 seconds.
4. Reinsert the batteries.
5. Close the battery compartment cover.
6. Your Sparmatic Comet restarts and is then in the adaptation mode.

INFORMATION
Please note that your Sparmatic Comet must be re-adapted after each battery change. Stored heating programmes are retained. If necessary, check the date and time (see  Section 5.2 Setting date and time on Page 11).

REMOVING SPARMATIC COMET

A prerequisite for removing your Sparmatic Comet is that ADAP is shown in the display.

CAUTION!: Burns caused by hot radiator valve!

• Touching can cause burns to the hand.
• Avoid contact of battery acid with skin, eyes and mucous membranes.
• Allow the radiator to cool down before installing, removing or troubleshooting your Sparmatic Comet!

1. Turn the setting wheel beyond the highest temperature of 28 °C.
2. ON appears in the display.
3. Turn the union nut anti-clockwise.
4. Pull your Sparmatic Comet off the valve (see illustration).
5. You have removed your Sparmatic Comet.

OPERATING MODES & FUNCTIONS

The following section describes the operating modes and other functions of your Sparmatic Comet.

BASIC OPERATING MODES

MANU MODE
In the MANU mode, your Sparmatic Comet regulates according to the temperatures set manually with the setting wheel:

AUTO MODE

• In the AUTO mode, your Sparmatic Comet alternates between two temperatures according to the set heating programme:
  • Comfort temperature (factory setting 21°C)
  • Economy temperature (factory setting 16°C)
• The heating and economy times are set in the heating programme. You can set a maximum of 8 switching points per day. Your Sparmatic Comet is set to the following default setting at the factory:
  • Heating time Heating to comfort temperature (Factory setting: 1st heating time at 7 a.m.)
  • Economy time Reduction to economy temperature (Factory setting: 1st economy time at 10 p.m.)

SETTING HEATING AND ECONOMY TIMES

• With the Sparmatic Comet you can set 4 heating and 4 economy times per day – for each day individually or for several days in a block.
• DAY1 to DAY7 stand for the respective weekdays from Monday to Sunday. In addition, the corresponding days are shown below the bar as abbreviations in the display.

Forming blocks

• T1–5 = same program Monday to Friday
• T1–6 = same program Monday to Saturday
• T1–7 = same program Monday to Sunday

For days that are not programmed, the factory settings remain active.

Setting individual program
Set an individual program:

1. Navigate to the menu item PrO and confirm with the OK button.
   The display shows DAY1 for Monday.

2. Select the day/block with the setting wheel and confirm with the OK button.

3. Use the setting wheel to set the start of the 1st heating time and confirm with the OK button.

4. Use the setting wheel to set the start of the 1st economy time and confirm with the OK button.

5. Set additional heating/economy times if required.

6. If you do not want to set any more heating/economy times, press the OK button twice to confirm the — — display. First confirm the heating time and then the economy time (the respective symbols are shown in the display).

7. The next day to be programmed appears in the display.

8.  If you do not want to set another day, press the Menu button to save the settings.

9. Programming is complete and the display shows the temperature.

10. Your Sparmatic Comet heats in the AUTO mode according to your set program.

INFORMATION
You can also overwrite individual days with different times within blocks.

Setting comfort and economy temperature

1. Navigate to the menu item TEmP and confirm with the OK button.
2. Set the comfort temperature with the setting wheel and confirm with the OK button.
3. Set the economy temperature with the setting wheel and confirm with the OK button.
4. Your Sparmatic Comet then switches to the set heating program.

INFORMATION

• If you turn the setting wheel beyond the highest temperature of 28 °C, ON is shown in the display.
• The valve is completely open.
• If you turn the setting wheel beyond the lowest temperature of 8 °C, OFF is shown in the display.
• Frost protection is active.
• Maximum energy savings are achieved at an economy temperature that is approx. 5°C below the comfort temperature.

MANUAL OPERATION
The temperature can be changed at any time using the setting wheel. In the AUTO mode, this remains unchanged until the next switching point. Your Sparmatic Comet then switches to the set heating programme.

ADDITIONAL FUNCTIONS

VENTILATION DETECTION
If the temperature drops sharply due to an open window, your Sparmatic Comet automatically closes the heating valve for 10 minutes to save energy. WIND appears in the display. Your Sparmatic Comet then returns to normal operation. Set the window function individually:

1. Navigate to the menu item WIND and confirm with the OK button.
2. Set the desired sensitivity (HIGH = high, MId = medium, LOW = low) with the setting wheel and con-firm with the OK button.
3. Set the desired time period (factory setting 10 minutes) with the setting wheel and confirm with the  OK button.
4. You have set the ventilation detection.

HOLIDAY FUNCTION
You can set a freely selectable temperature for the time you are absent. After the set time has elapsed, the heating programme set by you runs again automatically.

1. Navigate to the menu item HoLI and confirm with the OK button.
2. Use the setting wheel to set the date and time for the beginning of the period of absence and confirm with the OK button.
3. Use the setting wheel to set the date and time for the end of the period of absence and confirm with the OK button.
4. Set the temperature with the setting wheel and confirm with the OK button.
5. As soon as the holiday period begins, the symbol appears in the display. After the set absence period has elapsed or by pressing the Menu button , the symbol goes out.

OFFSET TEMPERATURE ADJUSTMENT

If the temperature felt differs from the set temperature, you can perform a temperature adjustment:

1. Navigate to the menu item OFFS and confirm with the OK button.
2. The degree setting 0.0°C flashes in the display.
3. Set the desired adjustment (from -5 to +5°C) of the temperature with the setting wheel and confirm with the OK button.
4. You have set the temperature adjustment.

BUTTON LOCK/CHILD SAFETY DEVICE
To protect against unauthorised operation, you can lock the buttons of your Sparmatic Comet:

1. Press the Menu + OK buttons simultaneously for approx. 2 seconds.
2. The symbol is shown in the display.

INFORMATION
Press the Menu + OK buttons again simultaneously for approx. 2 sec. to cancel the button lock.

TIMER FUNCTION
With the timer function, any temperature can be set for an individual period of time. This can be useful, for example, at a party:

1. Press the Timer button.
2.  Set the period of time with the setting wheel and confirm with the OK button.
3. Set the temperature with the setting wheel and confirm with the  OK button.
4.  You have set the timer function.

INFORMATION

• A manual temperature change is then not possible in the selected period; the setting wheel is locked.
• Press the button Menu to cancel locking.

FROST AND LIME PROTECTION

• The frost protection and limescale protection functions are automatically active.
• Frost protection: If the temperature drops below 8°C, the Sparmatic Comet opens the valve until the temperature rises above 8°C again. This prevents the radiators from freezing.
• Lime protection: To prevent the radiator valves from calcifying, the Sparmatic Comet carries out a limescale protection run 1× a week (Friday morning).

HEATING BREAK/CLOSE VALVE
You can close the valve if necessary.

1. Navigate to the menu item MODE and confirm with the OK button.
2. Select MANU with the setting wheel and confirm with the OK button.
3. Use the setting wheel to set the temperature in the display to OFF.
4. The valve is closed and operates without a time programme. The limescale protection function 1× weekly remains active.
5. Select AUtO in the menu to restart the heating programme you have set.

SUMMER AND WINTER TIME CHANGEOVER
The automatic summer/winter time changeover is switched on at the factory.

1. Navigate to the menu item dSt and confirm with the button.
2. Use the setting wheel to select ON (setting switched on) or OFF (setting switched off) and confirm with the button.
3. You have set the automatic summer and winter time.

SETTING LCD DISPLAY STANDBY

1. Navigate to the menu item STBY and confirm with the OK button.
2. Select ON (stand-by mode switched on) or OFF (stand-by mode switched off) with the setting wheel and confirm with the OK button.
3. When the temperature is changed or the menu is opened, the display automatically switches to the stand-by mode after approx. 30 seconds. When the button is pressed once, the display wakes up and switches off after 60 seconds.

RESETTING TO FACTORY SETTINGS
If problems occur, it may be helpful to reset your Sparmatic Comet to the factory settings.

1. Navigate to the menu item rES and confirm with the OK button.
2. YES? is shown in the display.
3.  Confirm with the OK button.
4. Your Sparmatic Comet is in the state it was delivered in.
5. If necessary, carry out initial operation, see Section 5 Putting into Operation on Page 10

TROUBLESHOOTING

Problems can also occur with your Sparmatic Comet. The following information will help you eliminate errors.

CLEANING AND STORAGE

Switch off your Sparmatic Comet and remove the batteries if you will not be using your Sparmatic Comet for a longer period of time. Store your Sparmatic Comet in a dry, dust-free place.

IMPORTANT! Material damage possible!
Improper handling of your Sparmatic Comet may result in damage.

• Do not immerse your Sparmatic Comet in water or other liquids.
• Do not use aggressive cleaning agents, brushes with metal or nylon bristles or sharp or metallic cleaning objects such as knives, hard spatulas, etc. They can damage the surfaces.
• Clean your Sparmatic Comet with a soft, dry, lint-free cloth.
• Do not use cleaning agents or solvents.

APPENDIX

The following section contains information on technical data, customer service and other legal informa-tion.

TECHNICAL DATA

Designation Sparmatic Comet

• EAN 4260012710472
• Article number 700012
• Supply voltage 2× 1.5 V AA/LR6
• Threaded connection M30 × 1.5 mm
• Display LCD
• Dimensions 84 mm × 65 mm × 54 mm
• Weight 152 g (incl. batteries)
• Permissible ambient temperature 5 to 55 °C
• Surface temperature max. 90 °C (on radiator)
• Linear stroke 4.3 mm

Subject to technical changes at any time. Compatibility information provided without guarantee.

SUPPORT AND CONTACT

• You can contact us for technical support.
• We look forward to assisting you with your enquiry:
  • Phone: +49-(0)-6667-91847-0
  • E-mail: support@eurotronic.org
  • Customer service: EUROtronic Technology GmbH
• Südweg 1
• 36396 Steinau-Ulmbach
• Germany

DISPOSAL

INFORMATION
Please inform yourself about the options for returning old devices and used batteries free of charge at your retailer.

From the date of implementation of the European Directives 2012/19/EU into national law, the following applies:

• Electrical and electronic devices as well as batteries may not be disposed of with household waste. The consumer is legally obliged to return electrical and electronic devices as well as batteries at the end of their service life to the public collection points set up for this purpose or to the point of sale. Details are regulated by the respective national laws.
• Non-rechargeable and rechargeable batteries may not be disposed of in household waste! As a consumer, you are legally obliged to hand in all non-rechargeable and rechargeable batteries, regardless of whether they contain harmful substances* or not, to a collection point in your municipality/district or to a retailer so that they can be disposed of in an environmentally friendly manner.
• *Labelled with: Cd = Cadmium, Hg = Mercury, Pb = Lead

DISPOSAL OF PACKAGING:
Dispose of the packaging according to type. Dispose of cardboard and carton at waste paper collection

Appendix

• points and foil at recyclables collection points. The symbols on your Sparmatic Comet, the operating instructions or the packaging refer to these regulations. With recycling, material recovery or other forms of recovery of used devices/batteries, you make an important contribution to the protection of our environment.
• This symbol is only valid for Italy.

SIMPLIFIED DECLARATION OF CONFORMITY
EUROtronic Technology GmbH hereby declares that your Sparmatic Comet complies with all applicable Community provisions of the European Economic Area Directive 2014/53/EU. The entire text of the EU Declaration of Conformity is available at the following Internet address: https://eurotronic.org/service/downloads

WARRANTY NOTICE

• The warranty period is 24 months and begins on the day of purchase. Keep your receipt as proof of purchase. During the warranty period, defective energy-saving controllers can be sent to the service address with sufficient postage. To do this, contact our Customer Service before returning the item. You will then receive a new or repaired device in return free of charge. Repair or replacement of the device does not be-gin a new warranty period. Note that we only guarantee the functions of the device, not the functionality between the interaction of the device and the valve base.
• The application-related technical data are only guaranteed together with the valves Heimeier, Junkers Landys+Gyr, MNG, Honeywell Braukmann thread dimension (M30x1.5), Oventrop (M30x1.5) Danfoss RA, RAV and RAVL. The unit combinations are specified on our website ( www.eurotronic.org ). When operating your Sparmatic Comet with third-party valves/adapters that are not listed, the functionality must be ensured by the user. EUROtronic does not provide warranty service in these cases.
• After the warranty period has expired, you also have the option of sending the defective unit to the ad-dress provided, with sufficient postage, for the purpose of repair. Repairs required after the expiration of the warranty period are subject to a charge. Your statutory rights are not limited by this warranty.

MANUFACTURER

EUROtronic Technology GmbH Südweg 1
36396 Steinau-Ulmbach Germany

EUROtronic Technology GmbH
Südweg 1 | 36396 Steinau-Ulmbach | Germany www.eurotronic.org

References

• Home | EUROTRONIC Technology GmbH
• Ingenieurbüro FORMAT | Experten für technische Dokumentationen
• Metalladapter | EUROTRONIC Technology GmbH
• FAQ | EUROTRONIC Technology GmbH

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>