Maisto 82767A 2.4CHz Cyklone Motobike Instruction Manual
- June 15, 2024
- Maisto
Table of Contents
Maisto 82767A 2.4CHz Cyklone Motobike
Product Information
Maisto Radio Control Vehicles
Warning! Not suitable for children under 36 months.Small parts.Choking hazard. Please keep this owner’s instruction manual for future reference. tt contains important information We reserve the right to improve/revise the product specifications without notice.
Class 1 LED Product
Contents
- Vehicle x 1
- Transmitter x 1
- Bracket Pad x 2
- Owner’s Instruction Manual x 1
Battery Requirement
- Vehicle : 4 x 1 .5V “AAA” LR03/R03 batteries.
- Transmitter : 2 x 1.5V “AAN’ LR03/R03 batteries
Battery installation for the Transmitter
(Refer to Diagram 1)
- Use a screwdriver to loosen the screw on the battery cover and to open the battery cover. (Screwdriver is not included)
- Install 2 new 1.5V “AAA” LROS/R03 batteries with correct polarity (+/-) as shown inside the battery compartment.
- Install the battery cover and then tighten the screw on the battery cover.
Battery installation for the Vehicle
(Refer to Diagram 2)
- Witch the power OFF.
- Use a screwdriver to loosen the screw on the battery cover and to open the battery cover. (Screwdriver is not included)
- Install 4 new 1.5V “AAA’ LR03/R03 batteries with correct polarity (+/-) as shown inside the battery compartment.
- Install the battery cover and then tighten the screw on the battery cover.
How to play
(Refer to Diagram 3, 4, 5 & 6)
- Set the ‘Power Switch” on the controller and vehicle to ON position, the “Power LED” on the vehicle will flash less than S seconds and then stay on, meaning the automatic frequency matching between the controller and the vehicle is completed.
- If the “Power LED” of the vehicle flashes more than 3 seconds, switch off both the vehicle and controller, then turn them on again.
- Pull the trigger in the transmitter to drive the vehicle forward. Push the trigger in the transmitter to drive the vehicle backward
- Turn the steering knob on the transmitter to steer the vehicle to right or left.
- Try different combinations of the trigger and steering wheel to perform different actions.
- Refer to diagram 6 to replace the new bracket pads.
- Periodically clean the dust on the caterpillar track for better performance.
- Turn the switch of the controller and vehicle to the OFF position when not in play.
Performance Tips
- Do not drive the vehicle on grass, sand, or go through water.
- Do not drive the vehicle in windy or rainy weather.
- Do not drive the vehicle into any hard object
- Keep fingers, hair, and loose clothing away from the vehicle.
- The operating range can be affected by a variety of factors:
- Weak transmitter or vehicle batteries.
- Interference from other items that emit radio frequency signals such as another RIC item on the same frequency, CB radios, cordless phones, high voltage transformers, etc.
- Outdoor usage is recommended to get oan optimal control range
Battery use
- Alkaline batteries are recommended.
- Only batteries of the same or equivalent type as recommended are to be used
- Do not mix alkaline, standard, or rechargeable batteries.
- Do not mix old and new batteries or different types of batteries.
- Non-rechargeable batteries are not to be charged.
- Rechargeable batteries are only to be charged under adult supervision.
- Rechargeable batteries are to be removed from the product before they are charged
- Be sure to insert batteries with correct polarities and always follow the battery manufacturer’s instructions.
- Remove all batteries from the product when not in use for long periods.
- Exhausted batteries are to be removed from the product.
- The supply terminals are not to be short-circuited.
- Dispose of batteries properly. Do not dispose of batteries in a fire — it may cause them to explode or leak causing injury or damage.
- Battery change must only be made by an adult.
Cautions
- Do not attempt to disassemble the products.
- Do not operate the vehicle with the same frequency as other players in the same location. This will interfere and cause the vehicle to lose control.
- Make Sure the batteries are installed with the correct polarity (+/-) as shown inside the battery compartment
- Remove the package, take out all accessories, and assemble the product before giving it to children to play with.
FCC Label Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions :
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
Warning : Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
RSS-210 Compliance Statement :
This device contains license-exempt that comply with Innovation, Science and
Economic Development Canada’s license-exempt RSS(s) Operation is subject to
the following two conditions:
- This device may not cause interference;
- This device must accept any interference, including interference that may cause undesired operation of the device
Troubleshooting
Environmental notes:
The whole product also does not belong to household waste at the end of the
product life. You can return it at collection points for the recycling of
electronic and electronic instruments The symbol on the item, instruction
manual, hangtag or packing shows this clearly. Materials should be recycled
according to their respective markings. Recycling of old devices or other re-
use of materials contained therein represents an important contribution to
environmental protection. Please ask your local community for the correct
collection point. Please retain this sheet and address for future use, as they
contain important information.
Disposal of batteries
Batteries should not be disposed of in the household waste. As the consumer
you are legally obliged to return batteries containing harmful substances and
all other used batteries. You can hand in your old batteries at public
collection points in your area or wherever batteries are sold. You will find
these chemical abbreviations along with a crossed-out refuse bin On batteries
containing harmful substances:
- Pb = Battery contains lead
- Cd = Battery contains cadmium
- Hg = Battery contains mercury
CE Declaration
Hereby, MAY CHEONG GROUP FRANCE S.A.S., declares that this equipment is in
compliance With the essential requirements and other relevant provisions of
directive 2014/53/EU.
- Frequency : 2.4GHz
- Transmitting frequency band: 2.4-2.4835GHz
- Max allowed transmitting power: <10mW
The declaration of conformity may be consulted at:
MAY CHEONG GROUP FRANCE S.A.S.; parc Ariane – Le Vénus, 2 rue Héléne Boucher,
78280 Guyancourt, France
The full text of the declaration of conformity is available at the following internet address: www.maycheonggroup.com.hk/declaration-of- conformity
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>