eRapta A1TYZX7 Solar Wireless Backup Camera Installation Guide
- June 15, 2024
- eRapta
Table of Contents
A1TYZX7 Solar Wireless Backup Camera
Specifications
-
Product Name: eRapta Solar Wireless 7 Camera System
(ATYZX7) -
Power Requirement: 12-24 Volt Direct Current
-
Camera Charging Time: 4-6 hours
Product Usage Instructions
1. Package Listing
Thank you for choosing eRapta solar wireless backup camera
system ATYZX7! Please check the external packaging for any signs of
rough handling. Open the package and inspect the items for any
damages caused by transportation. If any items are missing or
damaged, please contact us at: [email protected]
2. Introduction and Specification
2.1 Specification
The eRapta solar wireless backup camera system is designed to
observe surroundings and assist parking. It includes a monitor, a
camera, and other accessories needed for installation. The system
requires 12-24 Volt Direct Current power to operate. To ensure
proper installation and avoid damage caused by electricity shock,
we recommend hiring a qualified and experienced engineer.
2.2 Introduction to Camera
The camera features a pair button and a power screen. To pair
the camera, open the rubber cover and long press the pair button
with a thin stick. The camera has a Type-C charging port for
charging its battery using 12-volt direct current power. The
battery usually takes 4-6 hours to fully charge. An indicator light
on the camera shows the power status. When the battery is low, the
indicator light flashes in red. During charging, the light remains
red. When the battery is sufficient, the light turns off.
2.3 Introduction to Monitor
2.3.1 Icons on the Screen
-
Signal Icon: Indicates the camera signal
strength -
Battery Icon: Displays the camera’s battery
status -
Solar Charging Icon: Indicates solar charging
is in progress
2.3.2 Buttons on the Monitor
The monitor has six buttons on the top. From left to right, they
are POWER, +, -, CH, M, S. Please refer to the operation
instructions to learn their functions.
-
Power On/Off: Press this button to light up
the screen and automatically connect the camera to show the reverse
scene when reversing or needing to use the reverse system. When all
settings are exited, including the reversing line setting, press
this button again when the screen is lit to turn off the screen and
automatically disconnect it from the camera. -
Right/Increase: When entering the menu, use
this button to select different options.
FAQ
-
I received a broken or missing item in the package.
What should I do?If you find any items broken or missing from the package, please
contact our sales team at [email protected]. We will assist
you with a solution. -
How long does it take to charge the camera’s
battery?The camera’s battery can be fully charged in 4-6 hours using a
12-volt direct current power source. -
Do I need to hire a professional for the system
installation?To ensure proper installation and avoid damage caused by
electricity shock, we recommend hiring a qualified and experienced
engineer for the system installation. -
How do I turn on/off the monitor? To turn on the monitor, press the POWER button. When you are
done using the monitor, press the POWER button again to turn it
off.
eRapta Solar Wireless 7 Camera System (ATYZX7)
Installation and Operation Guide
Foreword
Thank you for purchasing our product! eRapta has always been commied to
providing high-quality products, and bringing a good experience to our
customers. It’s our great honor to have your trust! This manual includes
product installaon guide and system operaon instrucons. To obtain the best
performance, please read the manual carefully before installing, and keep the
manual properly.
If you’re experiencing the following situaons: 1. Open the package, finding
something is broken or missing. 2. Open the package, and don’t like the
product. 3. Order a wrong product. 4. Need technical support. 5. Encounter
problems with the camera or monitor in use. 6. Have any other problems or
needs.
Please feel free to e-mail our aer-sales team at any me: [email protected]
Each of your messages will be answered within 24 hours. We will help you solve
your problems, and provide you with the best aer-sales service and technical
support!
Contents
1. Package List……………………………………………………….. 1 2. Introducon and
Specificaon………………………………. 3 2.1 Specificaon……………………………………………………… 3 2.2
Introducon to Camera………………………………………. 3 2.3 Introducon to
Monitor……………………………………… 5 2.4 Introducon to Accessories…………………………………. 8 3.
Installaon Guide……………………………………………….. 11 3.1 Make an Installaon
Plan…………………………………… 11 3.2 Monitor Installaon………………………………………….. 12 3.3 Camera
Installaon…………………………………………… 14 4. System Operaon……………………………………………….. 16 4.1
Primary Menu…………………………………………………… 16 4.2 Secondary Menu……………………………………………….. 17
4.2.1 Pairing Seng………………………………………………… 17 4.2.2 Image
Parameters…………………………………………… 19 4.2.3 Image Rotaon……………………………………………….. 20 4.2.4
Screen Timeout………………………………………………. 21 4.2.5 Parking Guideline:
ON/OFF………………………………. 22 4.2.6 Parking Guideline Adjustment………………………….. 23 5.
FAQ…………………………………………………………………… 24 6. Warranty……………………………………………………………. 25
1. Package Listing
Thanks for choosing eRapta solar wireless backup camera system ATYZX7! We are
commied to providing you with the best quality products, so our product will
serve you for years. Please check the external packaging to see whether there
are any signs of rough handling. Also open the package, and check the items to
see whether there are damages caused by transportaon.
1
The image above provides an overview of all the items in the package. If any
items are missing or damaged, please contact us at : [email protected]
2
2. Introduction and Specification
2.1 Specificaon
The system is designed to observe surroundings and assist parking, including a
monitor, a camera, and other accessories needed to install. It requires 12-24
Volt Direct Current power to work. To avoid damage caused by electricity shock
or improper installaon, we recommend a qualified and experienced engineer to
install the system for you.
2.2 Introducon to Camera
Pair buon. Power screen, open the rubber cover, and long press it with a thin
sck can achieve pairing. Type-C Charging port. You can charge the camera’s
baery using 12 volt direct current power through this port. Usually, the baery
can be fully charged in 4-6 hours. Indicator Light of Power. When the baery is
low, the indicator light will be flashing in red. When charging, the light
will stay red. When the baery is sufficient, the
3
indicator light is off. Indicator Light of Pairing. Usually the camera will
pair automacally, otherwise select the pair opon and pair them manually. When
Pairing is in progress, the light will be flashing in green. When the pairing
is successful, the light will stay in green. When the screen is off, the light
is off. Camera. This camera is adjustable. You can adjust the lens 60 degrees
up and down to obtain the view you want. The camera has a bracket that can be
fixed to the license plate, and the camera can be easily installed or removed
by pushing. See Part 3 – Installaon Guide. Solar panel. Automac charging is
possible when there is no shade and is illuminated by light.
4
2.3 Introducon to Monitor
2.3.1 Icons on the screen
: This camera has signal : Camera baery status : Solar charging is in progress
2.3.2 Buons on the monitor
There are 6 buons on the top of the monitor. From le to right, they are POWER,
+, -, CH, M, S. Please read the operaon Instrucons carefully to learn their
funcons.
5
(1)
Power on/ off
When you are reversing or need to use the reverse system,
press
to light up the screen and it will automacally
connect the camera to show the reverse scene. When all
sengs are exited, including the reversing line seng, press
when the screen is lit, the screen will turn off and
it will automacally disconnect the screen from the camera.
(2)
Right/Increase
When entering the menu, you can select different opons by
pressing
to move to the right, or pressing – to move
to the le, and you can choose the opons by pressing S.
When entering the image sengs, you can increase the
parameters by pressing
and decrease it by pressing -.
(3)
Le/Decrease
When entering the menu, you can select different opons by
pressing + to move to the right, or pressing
to move
to the le, and you can choose the opons by pressing S.
When entering the image sengs, you can increase the
parameters by pressing + and decrease them by pressing
.
(4)
Parking line switch/adjustment
6
is used for DIY reversing line. There are four opons to
adjust the reverse line by pressing
, they are height H,
width W, posion M, and cancel the reverse line. In the H
state, the height of the reversing line can be adjusted by
pressing +, -. In the W state, the width of the reversing line
can be adjusted by pressing +, -. In the M state, the le and
right posion of the reversing line can be adjusted by pressing
+, -.
also has the funcon of displaying and canceling
the reversing line.
(5)
Menu page/Return
When you need to set up the system, you can enter the
menu by pressing
, select by +, – and confirm the
opon by S. Only when entering the image sengs, the
has a selecon role, with +, – to make image
adjustments. When finished seng, press
to exit
opons and menus.
(6)
Selecon
Aer pressing M to enter the primary menu, press the
to select the seng items and enter. Aer pressing S to
enter the secondary menu, press the
to confirm the
opon and exit the secondary menu.
7
2.4 Introducon to Accessories
2.4.1 Monitor acvate buon
1. It’s used to light up the screen when you need to see through camera. 2.
It needs to be paired with the monitor before use. Normally, the Pairing is
done Before leaving our factory. But you need to repair the buon if it lost
paired. See 4.2 for details on how to pair.
2.4.2 Cigaree lighter
1. It’s used to provide power to the screen. 2. The red buon above the
cigaree lighter turns on/ off the power.
8
2.4.3 Monitor Mount
1. It’s used to hold the monitor in the desired posion. 2. Two types of
mounts are available depending on the need.
2.4.4 Camera bracket
1. It’s used to fix the camera to the license plate.
2.4.5 Antenna
1. It’s used to strengthen the signal connecon between the camera and the
monitor.
2. It needs to be installed behind the monitor before pairing.
9
2.4.6 Plasc nut
1. It’s used to fix the monitor and the monitor mount. 2.4.7 USB charging
cable
1. It’s used to connect the charger and the camera.
2.4.8 2 Screws
1. It’s used to fix the camera bracket to the license plate.
10
3. Installation Guide
3.1 Make an Installaon Plan
Before installaon, we recommend you spend a lile me tesng the system. This can
help you confirm whether the system works normally before you install it on
your vehicle.
You can use a 12-24V power supply to power up the monitor and camera. Our
camera has been paired with the monitor before they leave our factory. If you
want to pair the camera with another channel, please see 4.2 pairing for
detailed pairing notes and methods.
Based on our experience, we recommend you follow the sequence below to finish
installaon: (1) Install monitor (2) Install camera (3) Connect monitor and
camera to power supply (4) Adjust the lens of camera according to your needs
11
3.2 Monitor Installaon
There are two bracket opons for screen mounng. And it can be mounted to the
dashboard or to the windshield. 1. Mount the antenna to the back of the
monitor. 2. Select a bracket. Place the plasc nut behind the bracket gimbal as
shown in the picture.
3. Insert the bracket gimbal into the gimbal mount at the back of the
monitor, as shown in the picture.
4. Place the base in the right posion and choose the right angle of the
monitor. Then ghten the plasc nut with the gimbal mount at the back of the
monitor. Now, the monitor
12
has been fixed with the monitor mount. 5. When you use the sucon cup holder,
first open the sucon cup locking buckle as shown in the posion. Wet the sucon
cup with water, fixed in the ideal posion, then press the sucon cup locking
buckle. Complete the installaon.
6. When you use the glued simple holder, first sck the 3M double-sided tape
to the boom of the holder. Choose the ideal posion and press the base of the
holder down hard to complete the fixaon. 7. Insert the Type-C of the cigaree
lighter connecon cable into the Type-C socket at the back of the monitor,
Insert the cigaree lighter into the car cigaree lighter base and press the red
buon above the cigaree lighter to light up it. 8. Screen installaon and
connecon is complete. Press the screen on/off key to use.
13
3.3 Camera Installaon
1. Remove the license plate screws. Place the camera bracket in front of the
license plate. The bracket direcon as shown In the picture. The screw holes on
both sides correspond to the license plate screw holes. Use the screws to fix
the bracket to the license plate.
2. Hold the camera close to the bracket, the camera direcon as shown in the
picture (logo on top). Push the camera hard from the right side to the le
side. When you hear a click, you can confirm that it is installed.
14
3. Check whether the camera has been firmly fixed. Adjust the camera lt angle
to find the most suitable viewing angle. 4. When you want to remove it, press
the camera against the bracket and push it out from the le side to the right
side with force. To prevent it from falling off easily, we ghtened the fixing
clips. So when you take it off, you need to use more force.
If you encounter any problems in the installaon, please feel free to contact
us: [email protected] We will provide professional technical support within
24h.
15
4. System Operation
This part describes the funcons of 5 panels in menu page. You can press M to
enter the menu page and adjust sengs by buons on the monitor. When you move
the cursor to a panel or a sub-panel, its icon will become gray. You can know
where your cursor by icons’ colors.
4.1 Primary Menu
Pairing seng: Pair the Acvate Buon/Camera to the monitor Image Parameters:
Brightness/ Contrast/ Saturaon Image Rotaon: Horizontal/ Vercal Flip Screen
Timeout: Setup to turn off the monitor aer 45s/60s/ 90s or turn off this
funcon Parking Guidelines: ON/ OFF
16
4.2 Secondary Menu
4.2.1 Pairing Seng
Before leaving our factory, the camera has already been paired with the
monitor. Generally, the product is automacally paired when the screen is on.
But you need to re-pair the camera if it lost paired. We recommend you finish
pairing before installing the system on your vehicle, because the monitor and
camera needs to be within 3 feet in pairing. Camera system pairing If you need
to do it manually, here are the steps: 1.Power up the monitor. 2.Open the
rubber cover on the pairing buon of the camera, and long press it with a thin
sck unl the system is paired
17
and the flash green light stays on. 3. If it’s sll not paired, then follow these steps. Press
to enter menu page. Press
to select the
(Pairing seng). Press
to confirm the
. Then
long press it with a thin sck unl the system is paired
successfully and the flash green light stays on.
Pairing ps:
Make sure the monitor has installed the antenna.
Keep the camera and monitor within 3 feet.
Monitor acvate buon pairing
Press
to enter menu page. Press
to select
(Pairing seng). Press
to confirm the
. Then
press the Monitor acvate buon. It will appear OK under
the
when it is paired successfully.
If the system is sll not paired, Please feel free e-mail to our aer-sales team at any me: [email protected]
18
4.2.2 Image Parameters
1. Press
to enter menu page.
2. Press
to select the
(Image seng).
3. Select brightness/contrast/saturaon by press
.
4. Increase the parameters by pressing
and decrease it
by pressing
.
5. Press
to confirm and exit the Secondary menu.
6. Press
to exit the menu page.
19
4.2.3 Image Rotaon
1. Press
to enter the menu page.
2. Press
to select the
(Image mirror/Flip seng).
3. Select flip or mirror image by press pressing
and
.
4. Press
to confirm and exit the Secondary menu.
5. Press
to exit the menu page.
20
4.2.4 Screen Timeout
1. Press
to enter menu page.
2. Press
to select the
(Display me seng).
3. Select different display me by press pressing
and
.
4. Press
to confirm and exit the Secondary menu.
5. Press
to exit the menu page.
Tips: When you select off to make the monitor stay on, it will
speed up the power consumpon and the life of the camera baery. When you set a certain duraon(45s,60s,90s), you need
to press the monitor acvate buon or
again to light
up it before each use. You can sck the buon to the steering
wheel or a more convenient place for easy access.
21
4.2.5 Parking Guidelines: ON/OFF
1. Press
to enter menu page.
2. Press
to select the
(Parking guide line seng).
3. Select on/off by press pressing
and
.
6. Press
to confirm and exit the Secondary menu.
7. Press
to exit the menu page.
22
4.2.6 Parking Guidelines Adjustment
1. Press
to enter the three different adjustment states of
parking guide line, or turn off the parking guide line.
2. When it appears H, the height of the parking guidelines can
be adjusted by pressing
or
.
3. When it appears W, the width of the parking guidelines can
be adjusted by pressing
or
.
4. When it appears M, the le and right posion of the
parking guidelines can be adjusted by pressing
or
.
23
5. FAQ
1. Q: How to solve the problem of “black screen”? A: Check if the screen and
camera are successfully paired. Check if the camera has power, and check if
the car charger can power the screen. 2. Q: Why does the monitor acvate buon
not match and not work? A: The monitor acvate buon needs to be connected to
the screen. So this acvate buon has a lithium baery inside. Therefore, it may
have run out of the baery when the acvate buon is not working. Replace the
baery and pair it with the monitor again then it will work properly. You can
contact us if it have run out of the baery or sll not working.
24
6. Warranty
Each of your messages will be answered within 24 hours. We will help you solve
your problems, and provide you with the best aer-sales service and technical
support!
Email : [email protected] Warranty: Lifeme Warranty
25