Ehaho 2FT Whip Lights with Spring Base Installation Guide

Ehaho 2FT Whip Lights with Spring Base Installation Guide

LED WHIP INSTALL AND GUIDE

Includes

Thank you for purchasing our universal LED RGB Whip. After receiving your package, please open it and check if the product has been damaged during shipping. Use the accessory list in the instruction manual to ensure that you have received all the necessary parts. If there are any issues or concerns, please do not hesitate to contact us at our customer support email: support@ehaho.com.

Part List:

Box comes with (single pc)

• LED Whip Light x1
  

• American Flag x1
  Gadsden Flag x1
  Leopard Flag x1

• Flag Mounting Kits
  x1

• Controller+
  Extension Whire
  x1

• RF Remote x1

Box comes with (combo set)

• LED Whip Light x2
  

• American Flag x2
  Gadsden Flag x2
  Leopard Flag x2

• Flag Mounting Kits
  x2

• Controller+
  Extension Whire
  x1

• RF Remote
  x1

Warning

1. It is recommended that this installation be performed by a licensed professional. The improper installation of this kit will void all warranties.
2. Please read the following instructions thoroughly before installing and operating this led whip.

Step1 Mount Up

1. Remove the bottom nut and the spring washer on the bottom of your quick-release mount.
2. Mount the LED WHIP into any openy%%” bolt mount on your vehicle. Make sure the flat washer is inbetween the whip and the mount.
3. Place the spring washer underneath the mount and then rescrew the bottom nut.
4. Have a pair? Go for round 2 and mount the 2nd whip the same way.

Step2 Get wired!

1. Grab your battery cord and connect it to the bottom hanging cord on your LED WHIP.
2. Have a pair? Connect the 3-prong plug coming out the side of the master LED WHIP to the plug coming from the slave LED WHIP.
3. Note: The slave LED WHIP cannot function without being connected to the master LED WHIP.
4. Connect the terminal wire to the Positive (+) and Negative(-) terminals of your vehicle battery.
5. Hide any extra wiring with zip ties.

Step3

Using the flag mounts to secure flag to the whip.

Step4

Tips: For better battery protection, please power the cord to the rocker switches first before going to the battery. With any issues, please feel free to contact Ehaho  Customer Service and we will address your issue in a timely manner.

Wiring method: A
Accessory switching power supply (When the key is turned on, the indicator light below will light up)

Wiring method B
Constant power supply/battery (The lower indicator light will only come on when the switch is turned to the ON position)

Step5

REMOTE CONTROLLER

• One-to-one Remote Control Setting
  Long press the ON button about 2-3 seconds, the whip lights flashes twice, which means the whips lights locked and only control by your controller and not affected by others remote controller.

  1. In order to prevent the whip lights from being interfered by other people’s remote controls, it is recommended to set your whip lights to one-to-one remote control mode during the initial installation.
  2. To avoid pairing your light with a whip light of the same style, do not enable the one-to-one remote control mode when there are other whip lights of the same style nearby. it is possible to choose a different location for setting or make sure other whip lights are turned off before setting.

• The music activation mode can be used only after adjusting the sensitivity of the external microphone in the “Magic Lantern” APP.

LED WHIP LIGHT APP GUIDE

1. Open the app and click “OK”. If you accidentally click “Don’t allow”, Please go into your phone’s settings and find “Magic-Lantern”. Then, allow Bluetooth through your phone’s settings. This is essential to connect your phone to your lights.

2. Turn on your phone’s Bluetooth. Then, plug in and turn on your LED Atmo- sphere Lights. After, click the icon in the top left corner of the app. You should see your lights appear under “My devices” (this may take up to 3 minutes). Click on your lights to finish pairing them with your app.
   

Music Mode

Currently music mode is only available for songs that have been downloaded onto your phone. Apple Music, Spotify, and other streaming services generally do not down- load songs to your phone. As a solution, you can use the “Mic” mode so that your lights automatically adjust to the sound of music.
To use mic mode, click “mic” in the bottom right of the screen. Then, click “OK” to allow the app to access your phone’s mic.

Music dancing lights pattern can be triggered by your phone’s mic or an external mic of the products. Set the sensitivity to adjust the External MIC to sense the external sound of frequency and intensity lights will sync with the sound’s frequency and intensity.

LED WHIP LIGHT LIGHTS

CONTROLLED BY LOTUSLANTERN APP

• Works with APP
• Long-range control convenient and quick
• Brightness control from 1% to 100%
• Seven romantic scene modes are optional
• More Than 16million of Colors
• Multi modes can be controled by one APP
• DIY selection by APP controller to createyour great led mood lighting
  

(Download “Magic-Lantern “from the App Store or Google Play Store.)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>