amazon basics B07WV5WN7B Wireless Keyboard User Manual

Wireless Keyboard – Quiet and Compact
BO7WV5WN7B

IMPORTANT SAFEGUARDS

Read these instructions carefully and retain them for future use. If this product is passed to a third party, then these instructions must be included.
When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons including the following:

• Never use this product if damaged.
• Do not insert any foreign objects into the inside of the casing.
• Protect the product from extreme temperatures, hot surfaces, open flames, direct sunlight, water, high humidity, moisture, strong jolts, flammable gases, vapours and solvents.
• Keep this product and its packaging out of the reach of children and pets.

Battery Safety Advice

• Keep batteries out of the reach of children. In particular, keep batteries which are considered swallowable out of the reach of children. In case of ingestion of a cell of battery seek medical assistance promptly. Swallowing batteries can cause chemical bums, perforation of soft tissue, and in severe cases can cause death. They need to be removed immediately if swallowed.

• Do not allow children to replace batteries without adult supervision.

• Always insert batteries correctly with regard to polarity (+ and ) marked on the battery and the equipment. When batteries are inserted in reverse they might be short-circuited or charged. This can cause overheating, leakage, venting, rupture, explosion, fire and personal injury.

• Do not short-circuit batteries. When the positive (+) and negative (-) terminals of a battery are in electrical contact with each other, the battery becomes short-circuited. For example loose batteries in a pocket with keys or coins, can be short-circuited. This can result in venting. leakage, explosion, fire and personal injury.

• Do not charge batteries. Attempting to charge a non-rechargeable (primary) battery can cause internal gas and/or heat generation resulting in leakage, venting, explosion, fire and personal injury.

• Do not force discharge batteries. When batteries are force discharged by means of an external power source the voltage of the battery will be forced below its design capability and gases will be generated inside the battery. This can result in leakage, venting,
  explosion, fire and personal injury.

• Do not mix new and used batteries or batteries of different types or brands. When replacing batteries, replace all of them at the same time with new batteries of the same brand and type. When batteries of different brand or type are used together or new and used batteries are used together, some batteries might be over- discharged / force discharged due to a difference of voltage or capacity. This can result in leakage, venting, explosion, fire and personal injury.

• Exhausted batteries should be immediately removed from equipment and properly disposed of. When discharged batteries are kept in the equipment for a long time electrolyte leakage can occur causing damage to the equipment and/or personal injury.

• Do not heat batteries. When a battery is exposed to heat, leakage, venting, explosion or fire can occur and cause personal injury.

• Do not weld or solder directly to batteries. The heat from welding or soldering directly to a battery can cause leakage, venting, explosion or fire, and can cause personal injury.

• Do not dismantle batteries. When a battery is dismantled or taken apart, contact with the components can be harmful and can cause personal injury or fire.

• Do not deform batteries. Batteries should not be crushed, punctured, or otherwise mutilated. Such abuse can cause leakage, venting, explosion or fire and can cause personal injury.

• Do not dispose of batteries in fire. When batteries are disposed of in fire, the heat build-up can cause explosion and/or fire and personal injury. Do not incinerate batteries except for approved disposal in a controlled incinerator.

• Always select the correct size and grade of battery most suitable for the intended use. Information provided with the equipment to assist correct battery selection should be retained for reference.

• Clean the battery contacts and those of the equipment prior to battery installation.

• Remove batteries from equipment which is not to be used for an extended period of time.

Intended Use

• This product is a wireless computer peripheral intended for interacting with your desktop/laptop.

Product Description

1. To turn on the Media player program
2. To decrease volume
3. To increase volume
4. To mute the sound
5. Previous track
6. Next track
7. To play/pause media playback
8. To stop media playback
9. To start the default Web browser and load the home page
10. To start the default e-mail client
11. To open up the folder ‘My Computer’
12. To open ‘My favorite’ when inside the browser
13. LED indicator Caps Lock on
14. 1 LED indicator Number Lock on
15. LED indicator Low battery and pairing indicator
16. Fn To enable the second function of the Function keys
17. CONNECT button o estabiish pairing with the nano receiver
18. Battery cover
19. Nanoreceiver

NOTICE: Press Fn + any function key (1 through 12) to trigger the secondary function of each key.

Installation

Installing the Batteries
NOTICE

• Always purchase the correct size and grade of battery most suitable for the intended use.
• Clean the battery contacts and also those of the device prior to battery installation.
• Ensure the batteries are installed correctly with regard to polarity (+ and -).
• Remove batteries from equipment that is not to be used for an extended period of time. Remove used batteries promptly.

1. Remove the battery cover.
2. Insert the batteries correctly with regard to polarity (+ and -) marked on the battery and the product.
3. Place the cover back over the battery compartment.

Pairing

• Plug the nano receiver into a USB port of your computer. The connection between keyboard and nano receiver should occur automatically.

If the connection between keyboard and the receiver fails or is interrupted, proceed as follows:

1. Remove the nano receiver from the USB port and plug it back in.
2. Press the CONNECT button of the keyboard.
   NOTICE: The LED indicator on the keyboard blinks when it is in pairing mode and stops blinking when it is successfully paired with the receiver.

LED Indicator
LED is on for 10 sec.
Power ON
LED blinking
During pairing (The LED goes off when pairing is successful or if it keeps failing for longer than 10 seconds.)
LED blinks for 10 sec.
Low battery warning

Cleaning and Maintenance

NOTICE: Switch the product off before cleaning.
NOTICE: During cleaning do not immerse the electrical parts of the product in water or other liquids. Never hold the product under running water.
Cleaning

• To clean the product, wipe with a soft, slightly moist cloth.
• Dry the product after cleaning.
• Never use corrosive detergents, wire brushes, abrasive scourers, metal or sharp utensils to clean the product.

Storage

• Store the product in its original packaging in a dry area. Keep away from children and pets.

FCC Compliance Statement

1. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
   (1) this device may not cause harmful interference, and
   (2) this device must accept any interference received, including interference that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Interference Statement
This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant tc part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Canada IC Notice

• This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’’s licence-exempt RSS(s). Operation is subject to the following two conditions:
  (1) this device may not cause interference, and
  (2) this device must accept any interference, including interference that may cause undesired operation of the device.

• This equipment complies with Industry Canada radiation exposure limits set forth for an uncontrolled environment.

• This Class B digital apparatus complies with Canadian CAN ICES- 003(B) / NMB-003(B) standard.

Slmplified EU Declaration of Conformity

• Hereby, Amazon EU Sarl declares that the radio equipment type BO7WVSEWN7B, B0787HH4L4, B0787KRLDQ, B0787HV36B, BO787KNB8YX, BO787KRFSW is in compliance with Directive 2014/53/EU.
• The full text of the EU declaration of conformity is available at the following internet address: https://www.amazon.co.uk/amazon_private_brand_EU_compliance

Simplified UK Declaration of Conformity
Hereby, Amazon EU SARL, UK Branch declares that the radio equipment type BO7WVSWN7B, B0787HH4L4, BO787KRLDQ, B0787HV36B, BO787KN8YX, BO787KRFOW is in compliance with The Radio Equipment Regulations 2017. The full text of the UK declaration of conformity is available at the following internet address: https://www.amazon.co.uk/amazon_private_brand_EU_compliance
Disposal
The Waste Electrical and Electronic Equipment (WEEE) Directive aims to minimise the impact of electrical and wmm clectronic goods on the environment, by increasing re-use and recycling and by reducing the amount of WEEE going to landfill. The symbol on this product or its packaging signifies that this product must be disposed separately from ordinary household wastes at its end of life. Be aware that this is your responsibility to dispose of electronic equipment at recycling centers in order to conserve natural resources. Each country should have its collection centers for electrical and electronic equipment recycling. For information about your recycling drop off area, please contact your related electrical and electronic equipment waste management authority, your local city office, or your household waste disposal service.

Battery Disposal

**** Do not dispose of used batteries with your household waste.
Take them to an appropriate disposal/collection site.

Specifications

Power Supply: 3V (2 x 1.5V AAA battery)
Current consumption: 50 mA
Weight – Keyboard: 1.05 Ibs (0.47 kg)
Dimensions- Keyboard: 17.83x 5.60x 1.13in (45.3cm x 14.23 x 2.86 cm)
Encryption: AES128
OS compatibility: Windows® 7/8/10
Transmission power: 1 mW
Frequency band: 2.4 GHz (2.402 GHz – 2.480 GHz)

Feedback and Help

Love it? Hate it? Let us know with a customer review.
AmazonBasics is committed to delivering customer-driven products that live up to your high standards. We encourage you to write a review sharing your experiences with the product.
US: amazon.com/review/review-your-purchases#
UK: amazon.co.uk/review/review-your-purchases#
US: amazon.com/gp/help/customer/contact- us
UK: amazon.co.uk/gp/help/customer/contact- us

amazon.com/AmazonBasics
MADE IN CHINA Vo2-11/22

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>