Ehaho L2800 RGB Double Projection Laser Lamp User Manual

L2800 RGB Double Projection Laser Lamp

RGB Double Projection Laser Lamp
L2800
User’s Manual

Questions or Concerns?
Our team will solve your any problems in 24hours
Support@ehaho.com
This manual contains important laser system safety and operation information. Read and understand all instructions prior to powering on laser unit the first time, to avoid laser eye injury and to avoid breaking the law. Keep this manual in a safe place for future reference.

General Instructions

Unpacking:
Thank you for purchasing this product. Please read user guide for safety and operations information before using the product. Keep this manual for future reference. This product can create perfect light programs and effects since it has passed a series of strictly tests before delivery. Please check the attachments listed on the page after opening the carton. Immediately upon receiving a fixture, carefully unpack the box. Check the box contents to ensure that all parts are present and that they are in good condition. If any part appears damaged from shipping, or if the box shows signs of mishandling, notify the shipper immediately.
What is included: 1 Light, 1Power Cable, 1User Guide ,1remote control Safety Notice: Please read the following notes carefully because they include important safety information about the installation, usage and maintenance of this product. It is important to read all these notes before starting to work with this product.
Lasers can be hazardous and have unique safety considerations. Permanent eye injury and blindness is possible if lasers are used incorrectly. Pay close attention to each safety REMARK and WARNING statement in the user manual. Read all instructions careful.
Laser Safety Warnings
Potential laser injury hazard exists with this product! Read these Instructions carefully, which include important information about installation, safe use and service!
Caution:

• *Avoid direct eye contact with laser light. Never intentionally expose your eyes or others to direct laser radiation.
• *This laser product can potentially cause instant eye injury or blindness if laser light directly strikes the eyes.
• *It is illegal and dangerous to shine this laser into audience areas, where the audience or other personnel could get direct laser beams or bright reflections into their eyes.
• *It is a US Federal offense to shine any laser at aircraft.

NON-INTERLOCKED HOUSING WARNING
*This unit contains high power laser devices internally. Do not open the laser housing, due to potential exposure to unsafe levels of laser radiation. The laser power levels accessible if the unit is opened can cause instant blindness, skin burns and fires.

Installation

Laser effects projected 3 meters (9.8 ft) above the audience are eye safe. A survey should be taken to assess the likelihood of any reflective surfaces (such as high windows, chrome bars etc) bouncing stray beams back down into the audience.
Using a fastening clamps on the light and tight to the ceiling in a strong hook..
*Make sure its correct power output and plug the power cable to the wall socket.

• Power must be in earth! Power on the light.
• Do not shoot the beams to the audience!
  Do not look direct into the laser aperture once the laser light is ON. Please pay attention to the Laser Danger Warning Label!
  Caution
  After setting up, and before public use, test laser to ensure proper function. Do not use if any defect is detected. Do not use if laser emits only one or two laser beams rather than dozens/ hundreds, as this could indicate damage to the diffraction grating optic, and could allow emission of higher laser levels above Class 3B.
  Do not point lasers at people or animals. Never look into the laser aperture or laser beams.
  Do not point lasers in areas in which people can potentially get exposed, such as uncontrolled balconies, etc.
  Do not point lasers at highly reflective surfaces, such as windows, mirrors and shiny metal. Even laser reflections can be hazardous.
  Never point a laser at aircraft, this is a federal offense.
  Never point un-terminated laser beams into the sky.
  Do not expose the output optic (aperture) to cleaning chemicals.
  Do not use laser if the laser appears to be emitting only one or two beams.
  Do not use the laser if the housing is damaged, the housing is open, or if the optics appear damaged in any way.
  Never open the laser housing. The high laser power levels inside of the protective housing can start fires, burn skin and will cause instant eye injury.
  Never leave this device running unattended.
  During Assembly, operation, maintenance, please pay special attention to avoid possible exposure to laser and collateral radiation in excess of the accessible emission limits.
  Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
  *Protective eye wear is typically required where direct viewing of a Class 3B laser beam may occur.
  The projector must be installed in a location with adequate distance.

Laser Expected Lifespan
Laser gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration of this decline. Packaged in clusters, Laser exhibit higher operating temperatures than in ideal or singular optimum conditions. For this reason when all color Laser are used at their fullest intensity, life of the Laser is significantly reduced. It is estimated that a viable lifespan of 5,000 to 10,000 hours will be achieved under normal operational conditions.If improving on this lifespan expectancy is of a higher priority, place care in providing for lower operational temperatures. This may include climatic-environmental and the reduction of overall projection intensity.

WHAT’S IN THE BOX

Double projection laser lamp x1
Power Cable x1
Remote Control x1
User Manual x1

INTRODUCTION

• Feature:Double-projection laser lamp combine RGBUV LED effect, Red and blue thebeam Light; Red and green pattern laser lamp; LED Strobe; so that a single device can display 4 effects, either work together or separate.
• Scanner High-speed optical scanner,big angle scanning
• Play Mode Sound Active, AUTO-Beam, DMX, Master/ Slave, Remote Control
• DMX channel: 18CH
• Power Supply Bi-Voltage: AC100V ~ 240V /2A, 50/60HZ
• Applicable place: company advertising, superstar fashion show, DJs, Bands, Bars, Pubs, Clubs, Roller skating rinks, KTV, Family Party, etc.

Fixture Rear Plate:

Digital display function: “Menu” is Menu, “Enter ” is confirm, “Previous” is UP, “Next ” is down.
Menu: Function mode selection, such as auto strobe, sound active strobe, DMX512 and Dimming mode（This dimming mode can only be set by staff. Please do not set this mode. ）
Up/Down: Previous/Next selection or Increase/Decrease selection.
Enter: Confirm and save the selection.
DISPLAY MENU:

LIG2 ( 1G00- 1G99)
LIG3 ( 2r00- 2r99 )
LIG4 ( 2b00-2b99 )
MOTO ( 1M00-1M99 )
RED(R000-R099)
GREE(G000-G099)
BLUE(B000-B099)
WHITE(W000-W099)
STRB(ST01-ST99)
Self-walking| AUT1 -AUT5
Sound-controlled| SOU1-SOU3
DMX address (18 CH)| A001-A512
Dimming mode| OFFS

DMX channel:

Mode 1 (18)| Passage|
---|---|---
1| Special channel| 000-005 without
006-050 Auto 1
051-090 Auto 2
091-140 sound-controlled 1
141-190 sound-controlled 2
191-240 sound-controlled 3
241-255 without
2| Pattern red laser| 000-255
3| Pattern green laser| 000-255
4| Jitter red laser| 000-255
5| Jitter blue laser| 000-255
6| DC Motor| 000-255
7| LED（red ）| 000-255
8| LED（green ）| 000-255
9| LED（blue ）| 000-255
10| LED（white）| 000-255
11| stroboscopic| 000-000 without
001-004 light
005-255 （Flash speed from slow to fast. ）
12| pattern| 000-004 Null
005-009 Pattern 1
010-014 pattern 2
015-019 pattern 3
020-024 pattern 4
025-029 pattern 5
030-034 pattern 6
035-039 pattern 7
040-044 pattern 8
045-049 pattern 9
050-054 pattern 10
055-059 pattern 11
060-064 pattern 12
065-069 pattern 13
070-074 pattern 14
075-079 pattern 15
080-084 pattern 16
085-089 pattern 17
090-094 pattern 18
095-099 pattern 19
100-104 pattern 20
105-109 pattern 21
110-114 pattern 22
115-119 pattern 23
120-124 pattern 24
125-129 pattern 25
130-134 pattern 26
135-139 pattern 27
140-144 pattern 28
145-149 pattern 29
150-154 pattern 30
155-159 pattern 31
160-164 pattern 32
165-169 pattern 33
170-174 pattern 34
175-179 pattern 35
180-184 pattern 36
185-189 pattern 37
190-194 pattern 38
195-199 pattern 39
200-204 pattern 40
205-209 pattern 41
210-214 pattern 42
215-219 pattern 43
220-224 pattern 44
225-229 pattern 45
230-255 point
13| Starting point of Pan axis| 000-199 Move left and right
200-255 Automatic left-right movement
14| Tilt axis starting position| 000-199 Move up and down
200-255 Move up and down automatically
15| Pattern fixed point rotation| 000-063 in situ
064-127 Rotate 90 degrees
128-191 Rotate 180 degrees
192-255 Rotate 270 degrees
16| flip| 000-009 NULL
010-120 Turn fast to slow
121-134 NULL
135-245 Reverse slowly to quickly
246-255 NULL
17| stretch| 000-009 NULL
101-120 Turn left and right fast and slow.
121-134 NULL
135-245 Flip up and down slowly to fast
246-255 NULL
18| Integral rotation| 000-127 Big to small
128-255 Scaling changes from slow to fast

REMOTE CONTROL FUNCTION:

+Led
AUTO2| Light effect:Red and Blue Thebeam Light + Led
AUTO3| Light effect:Red and Green Pattern Light + Led
SOUND1| Sound active mode 1,The sound active sensor works in high level of sensitivity, light works immediately with some SOUNDS, and turn off immediately without SOUNDS.
SOUND2| Sound active mode 2,When the music sound is loud enough and the rhythm is strong, you can accelerate the color change with the music rhythm. When there is no music, turn off the light.
SOUND3| Sound active mode 3,When the music is loud enough and the rhythm is strong, the color change will be accelerated. When there is no music, it will flash automatically.
SHOW| Under Auto 1, Auto 2, SOUND 1, SOUND 2, SOUND 3, press this button to switch to manual beam effect, press one cut to replace the next effect cycle
MOTOR STOP START| Dc motor switch, this button controls the red and green pattern laser motor  stop/start, but does not control the beam lamp motor stop/start
STROBE| Led Strobe mode
LED R/G/B| The red, green and blue LEDs are always on, and this button can be turned on/off. If you want to select monochrome after pressing this button, you can press this button to turn it off, and then select other LED color buttons.
LED Red| The red, green and blue LEDs are always on, and this button can be turned on/off. If you want to select monochrome after pressing this button, you can press this button to turn it off, and then select other LED color buttons.
LED Green| The green LED is always on, this button can be turned on/off, and you can choose the LED red and blue as well as UV to match. If you don’t want to mix the colors, you need to turn off LED red and blue and UV again,
LED Blue| The blue LED is always on, this button can be turned on/off, and you can choose LED red and green as well as UV to match. If you don’t want to mix colors, you need to turn off LED red and green and UV again
FLASH| Red and Blue Thebeam Light + Red and Green Pattern Light + Led Flash mode
SLOW| Press LED RGB, LED red, LED green and LED blue modes first, and then press this key to perform LED stroboscopic and reduce the speed.
FAST| Press this button again in LED RGB, LED Red, LED green and LED blue mode to perform LED stroboscopic and speed up.
SOUND
SENSITIVITY| This button adjusts the voice-control sensitivity, and the voice- control sensitivity can be switched cyclically. (Use this function in SOUND 1, SOUND 2 and SOUND 3 modes.)
Thebeam Light1| Red beam light mode, button to turn on or off the effect, you can choose beam light 2, mode light 3 and mode light 4 to use together.
Thebeam Light 2| Blue beam light mode, button can turn on or off the effect, you can choose beam light1, pattern light 3 and pattern light 4 to use together.
Pattern Light 3| The red pattern laser effect can be turned on or off. You can choose a combination of beam light 1, beam light 2 and pattern light 4
pattern Light 4| The green pattern laser effect can be turned on or off.. You can choose beam light 1, beam light 2 and pattern light 3 together.

Warranty Warnings:

1. Damages caused by the disregard of this user manual are not subject to Warranty.
   The dealer will not accept liability for any resulting defects or problems.

2. Please consider that unauthorized modifications on the device are forbidden due to safety reasons.
   Please note that damages caused by manual modifications on the device or unauthorized operation by unqualified persons are not subject to warranty.

3. If this device will be operated in any way different to the one described in this manual, it may suffer damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-circuit, burns electric shock, etc.
   For any questions about this light, please contact your dealer or our company for service.

RGB Double Projection Laser Lamp

Made In China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>