AVSL 156.788UK 24V IP20 High Output LED Tape 5m User Manual
- June 15, 2024
- AVSL
Table of Contents
AVSL 156.788UK 24V IP20 High Output LED Tape 5m
Product Information
- Specifications
- Color temperature: 3000K Warm White or 6000K Cool White
- Voltage: 24Vdc
- Beam angle: Not specified
- LED Type: Not specified
- Reel Length: 5m
- IP Rating: IP20 (for indoor use only)
- Power consumption per meter: Not specified
- Current per meter: Not specified
- LED quantity per meter: 120
- LED spacing: Not specified
- Cut points: Every 5cm
- Cross-section: Not specified
- Weight: Not specified
- Introduction
- Lyyt IP20 High Output LED Tape is a versatile lighting solution supplied on 5m reels.
- It operates from a 24V DC power supply and features 120 LEDs per meter.
- The tape is available in two color temperature options, 3000K Warm White or 6000K Cool White. The tape can be easily cut to the desired length at the designated cutting points every 5cm.
- The 24V High Output LED Tape is suitable for various applications such as hospitality, retail, offices, displays, exhibitions, and more. Please note that the IP20 version is for indoor use only.
Product Usage Instructions
- Installation
- Ensure proper installation by following relevant electrical safety procedures.
- Prepare a clean, non-porous surface for mounting the LED tape.
- Peel off the self-adhesive backing of the LED tape and firmly attach it to the chosen surface.
- If less than 5m of tape is needed, locate the solder points at intervals and cut the tape to the desired length.
- Connecting Cut Tape Lengths
- If you need to reconnect a cut tape to another length, follow the steps:
- Solder a wire from the positive (+) terminal of one cut tape length to the positive (+) terminal of the other cut tape length.
- Solder a wire from the negative (-) terminal of one cut tape length to the negative (-) terminal of the other cut tape length.
- Some accessories are supplied with the tape reel for this purpose.
- Power Supply Connection
- Each 5m reel of tape is fitted with a 2.1mm DC jack for easy power input connection to a compatible power supply. Follow these steps:
- Connect the 2.1mm DC jack of the LED tape to the corresponding jack on the power supply.
- If your power supply does not have a 2.1mm DC jack, you can remove and strip the connector to expose bare wires for connection.
- Connecting Multiple Reels
- If your power supply has enough capacity, you can connect another reel to the end of the first reel. Follow these guidelines:
- For 24V tape, up to 25m can be linked in this manner.
- To avoid dimming at the far end due to voltage drop, it is recommended to use a separate wire to loop the positive (+) and negative (-) terminals back to the power supply.
- If you need to connect beyond 25m, a parallel wire must be run from the power supply to the further reels of tape.
- FAQ (Frequently Asked Questions)
- Q: What is the recommended power supply for Lyyt LED Tapes?
- A: Please visit www.avsl.com. to select from our range of 24Vdc power supplies that are suitable for powering Lyyt LED Tapes.
- Q: How should I dispose of this product at the end of its useful life?
- A: This product is classified as Electrical or Electronic equipment and should not be disposed of with other household or commercial waste. Please follow your local council guidelines for proper disposal.
- Q: Can I use controllers and amplifiers/repeaters with this LED tape?
- A: Yes, you can use controllers and amplifiers/repeaters with the LED tape. However, make sure they have adequate capacity for the tape being controlled.
Introduction
- Lyyt IP20 High Output LED Tape is supplied on 5m reels and operates from a 24V DC power supply.
- The tape consists of 120 LEDs per meter and is available in either 3000K Warm White or 6000K Cool White varieties.
- The tape can be cut to the desired length on the designated cutting points every 5cm.
- The 24V High Output LED Tape has a wide variety of applications such as in hospitality, retail, offices, displays, exhibitions and more.
- IP20 versions are for indoor use only.
Specification
| Colour temperature | 156.786UK: 3000K, 156.788UK: 6000K |
|---|---|
| Voltage | 24Vdc |
| Beam angle | 120° |
| LED Type | 2835 Sanan |
| Reel Length | 5m |
| IP Rating | IP20 |
| Power consumption p/m | 12.8W |
| Current p/m | 533mA |
| LED quantity p/m | 120 |
| LED spacing | 8.3mm |
| Cut points | 5cm |
| Cross-section | 10 x 1.2mm |
| Weight | 230g |
- This product is intended to be professionally installed, observing relevant electrical safety procedures.
- Lyyt LED Tape has a self-adhesive backing to allow it to be easily attached to a clean, non-porous surface.
- Where less than 5m of tape is needed, there are solder points as shown below, where the tape may be cut to size.
- These cut points are at 5cm intervals.
- To re-connect to another length of tape after cutting, solder a wire from “+” to “+” and a wire from “-” to “-” as shown below.
- Some accessories are supplied with the tape reel for this purpose.
- For best protection of this tape, we recommend inserting the tape into one of our Aluminium Profiles.
- Each 5m reel of tape is fitted with a 2.1mm DC jack for power input for easy connection to a power supply.
- This connector may be removed and stripped for bare wire connection if a 2.1mm jack is not fitted to the power supply.
- If the power supply has enough capacity to power more than one reel, another reel can be connected to the end of the first reel.
- For 24V tape, up to 25m can be linked in this manner. Using a separate wire to loop “+” and “-” back to the power supply will help to avoid dimming at the far end through voltage drop.
- To connect beyond these lengths, a parallel wire must be run from the power supply to the further reels of tape.
- The power supply must have higher than the rated capacity in Amps (A) for the current required to power the length(s) of LED Tape installed.
- Likewise, if controllers and amplifiers/repeaters are used, these must have adequate capacity for the tape being controlled.
- Please see the table below for reference.
| Tape Length | 5m | 10m | 15m | 20m | 25m |
|---|---|---|---|---|---|
| Current for 24V tape 120 LED/m | 2.5A | 5A | 7.5A | 10A | 12.5A |
- Please visit www.avsl.com. to select from our range of 24Vdc power supplies that are suitable for powering Lyyt LED Tapes.
- This product is classed as Electrical or Electronic equipment and should not be disposed of with other household or commercial waste at the end of its useful life.
- The goods must be disposed of according to your local council guidelines.
CONTACT
- Errors and omissions excepted.
- Copyright© 2023 AVSL Group Ltd, Unit 2 Bridgewater Park, AVSL (Europe) Ltd, Unit 3D North Point House,
- Taylor Road, Trafford Park, Manchester.
- M41 7JQ. North Point Bus. Park, New Mallow Road, Cork, Ireland.
- lyyt Hi-Output LED Tape Manual
- www.avsl.com.
- 24V IP20 High Output LED Tape 5m
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>