INTIMSPOT360X 60 ILS Intimidator Free Spot
Specifications
- Product Dimensions: 5 inches (width) x 7 inches (height) x 3
inches (depth)
Usage Instructions
1. Before You Begin
What Is Included:
The following items are included in the package:
- Main unit
- AC power cable
- Mounting brackets
- User Manual
Unpacking Instructions:
When unpacking the product, please ensure that all the items
mentioned in the “What Is Included” section are present and
undamaged.
Claims:
If any items are missing or damaged, please contact our customer
support within 24 hours of receiving the product.
2. Introduction
Product Overview:
The product is a lighting fixture designed for professional use.
It provides various lighting effects and can be controlled via DMX
or operated in standalone mode.
3. Setup
AC Power:
To power the unit using AC power, follow these steps:
- Connect the AC power cable to the power input on the unit.
- Plug the other end of the AC power cable into a suitable power
outlet.
Fuse Replacement:
If the unit’s fuse needs to be replaced, follow these steps:
-
Unplug the unit from the power outlet.
-
Locate the fuse compartment on the unit.
-
Remove the old fuse and replace it with a new one of the same
rating.
-
Close the fuse compartment.
Battery Power:
If you want to power the unit using batteries, follow these
steps:
-
Open the battery compartment located on the back of the
unit.
-
Insert the required number of batteries according to the
specified type and polarity.
-
Close the battery compartment securely.
Charging the Battery:
If your unit has a rechargeable battery, follow these steps to
charge it:
-
Connect the AC power cable to the power input on the unit.
-
Plug the other end of the AC power cable into a suitable power
outlet.
-
The battery will automatically start charging. The battery life
indicator will show the progress of charging.
-
Once fully charged, disconnect the AC power cable from the
unit.
Battery Life Indicator:
The battery life indicator on the unit displays the remaining
battery life. It is recommended to charge the battery when the
indicator shows low battery level.
Battery Run Time:
The run time of the unit on battery power depends on various
factors such as brightness level, operating mode, and battery
capacity. On average, it can operate for up to 4 hours on a fully
charged battery.
Mounting:
The unit can be mounted using the provided mounting brackets.
Follow these steps to mount the unit:
-
Select a suitable location for mounting.
-
Attach the mounting brackets to the unit using the provided
screws.
-
Securely mount the unit to the desired surface using
appropriate hardware.
Orientation:
The unit can be used in any orientation, including vertical or
horizontal placement. Ensure that it is securely mounted to prevent
any accidental movement during operation.
Rigging:
If you need to rig the unit, it is recommended to consult a
professional rigger for proper installation and safety
measures.
4. Operation
Control Panel Operation:
The control panel on the unit allows you to access various
settings and features. Refer to the Menu Map section for detailed
information on navigating the control panel menu.
Menu Map:
The menu map provides a visual representation of the control
panel menu structure. Use it as a reference to navigate through
different settings and options.
DMX Configuration:
To configure the unit for DMX control, follow these steps:
- Access the DMX configuration menu on the control panel.
- Set the DMX personality and starting address according to your
setup requirements.
Gobos:
The unit supports different gobo patterns for creating unique
lighting effects. Refer to the user manual for a list of available
gobos and instructions on changing them.
DMX Values:
The DMX values control various parameters of the unit, such as
intensity, color, and movement. Refer to the user manual for a
detailed explanation of DMX values and their corresponding
effects.
Standalone Configuration:
If you prefer to operate the unit in standalone mode, follow
these steps:
-
Access the standalone configuration menu on the control
panel.
-
Select the desired run mode (e.g., manual mode).
Run Mode:
In the run mode, the unit will automatically cycle through
pre-programmed lighting patterns or follow DMX control signals.
Manual Mode:
In manual mode, you can manually control the unit’s settings
using the control panel buttons. Refer to the user manual for
detailed instructions on using the manual mode.
FAQ
Q: How long does the battery take to charge?
A: The charging time depends on the battery capacity and current
charge level. On average, it takes approximately 4-6 hours to fully
charge the battery.
Q: Can I use rechargeable batteries with the unit?
A: Yes, you can use rechargeable batteries. Ensure that the
batteries are compatible with the unit’s specifications.
Q: How do I change the gobo pattern?
A: To change the gobo pattern, follow these steps:
-
Access the gobo selection menu on the control panel.
-
Use the navigation buttons to scroll through available
gobos.
-
Select the desired gobo pattern and confirm your
selection.
Q: Can I connect multiple units together for synchronized
operation?
A: Yes, you can connect multiple units together using DMX cables
to achieve synchronized operation. Refer to the user manual for
detailed instructions on setting up a DMX network.
User Manual
TABLE OF CONTENTS
Table of Contents
1. Before You Begin …………………………………………………………….. 1
What Is Included ………………………………………………………………………………. 1 Unpacking
Instructions………………………………………………………………………. 1
Claims ……………………………………………………………………………………………………………. 1
Text Conventions ……………………………………………………………………………… 1 Symbols
………………………………………………………………………………………….. 1 Safety
Notes…………………………………………………………………………………….. 2 Battery Charge
Notes………………………………………………………………………… 2 FCC Statement of Compliance
…………………………………………………………… 3 RF Exposure Warning for North America and
Australia………………………….. 3 Disclaimer ……………………………………………………………………………………….. 3
2. Introduction …………………………………………………………………….. 4
Product Overview……………………………………………………………………………… 4 Product Dimensions
………………………………………………………………………….. 5
3. Setup ………………………………………………………………………………. 6
AC Power ………………………………………………………………………………………… 6
Fuse Replacement …………………………………………………………………………………………… 6
Battery Power…………………………………………………………………………………… 6
Charging the Battery ………………………………………………………………………………………… 6 Battery Life
Indicator ………………………………………………………………………………………… 6 Battery Run Time
…………………………………………………………………………………………….. 6
Mounting …………………………………………………………………………………………. 7
Orientation………………………………………………………………………………………………………. 7 Rigging
…………………………………………………………………………………………………………… 7
4. Operation ………………………………………………………………………… 8
Control Panel Operation…………………………………………………………………….. 8 Menu Map
……………………………………………………………………………………….. 8 DMX
Configuration……………………………………………………………………………. 9
DMX Personality and Starting Address……………………………………………………………….. 9
Gobos……………………………………………………………………………………………… 10 DMX Values
…………………………………………………………………………………….. 10 Standalone
Configuration…………………………………………………………………… 12
Run Mode……………………………………………………………………………………………………….. 12 Manual Mode
………………………………………………………………………………………………….. 12
Settings Configuration……………………………………………………………………….. 13
D-Fi Settings …………………………………………………………………………………………………… 13 Pan Reverse
…………………………………………………………………………………………………… 13 Tilt Reverse
…………………………………………………………………………………………………….. 13 Screen Reverse
………………………………………………………………………………………………. 13 Pan Range
……………………………………………………………………………………………………… 13 Tilt
Range……………………………………………………………………………………………………….. 13 Totem Mode
……………………………………………………………………………………………………. 14 Sound
Sensitivity……………………………………………………………………………………………… 14 DMX
Loss……………………………………………………………………………………………………….. 14 Indicator
…………………………………………………………………………………………………………. 14 Flash if
DMX……………………………………………………………………………………………………. 14 Run
Time………………………………………………………………………………………………………… 14 RF Setting
………………………………………………………………………………………………………. 15 Follow Spot
…………………………………………………………………………………………………….. 15 Product Reset
…………………………………………………………………………………………………. 15 Factory
Reset………………………………………………………………………………………………….. 15 Product
Information………………………………………………………………………………………….. 15
Intimidator Free Spot 60 ILS User Manual Rev. 2
PRODUCT NAME
Calibration Menu ………………………………………………………………………………. 16 ILS
Mode…………………………………………………………………………………………. 16 Master/Slave Mode
…………………………………………………………………………… 16 RFC Remote
Control…………………………………………………………………………. 17
RFC-XL Remote Control Operation ……………………………………………………………………. 17
5. Maintenance…………………………………………………………………….. 18
Product Maintenance ………………………………………………………………………… 18
6. Technical Specifications ………………………………………………….. 19 Contact Us
………………………………………………………………………….. 20
Warranty & Returns…………………………………………………………………………… 20
Intimidator Free Spot 60 ILS User
Before You Begin
1. Before You Begin
What Is Included
· Intimidator Free Spot 60 ILS · Power cable
· Omega bracket · Quick Reference Guide
Unpacking Instructions
Carefully unpack the product immediately and check the container to make sure
all the parts are in the package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear
damaged from shipping, or show signs of mishandling, notify the carrier
immediately, not Chauvet. Failure to report damage to the carrier immediately
may invalidate a claim. Keep the box and contents for inspection. For other
issues, such as missing components or parts, damage not related to shipping,
or concealed damage, file a claim with Chauvet within 7 days of delivery.
Text Conventions
Convention
1512 50/60 Settings
ON
Meaning
A range of values A set of values of which only one can be chosen A menu
option not to be modified A key to be pressed on the product’s control panel A
value to be entered or selected
Symbols
Symbol
Meaning
Electrical warning. Not following these instructions may cause electrical
damage to the product, accessories, or the user.
Critical installation, configuration, or operation information. Not following
these
!
instructions may make the product not work, cause damage to the product, or
cause
harm to the operator.
Important installation or configuration information. The product may not
function correctly if this information is not used.
Useful information.
1
Intimidator Free Spot 60 ILS User Manual Rev. 2
Before You Begin
Safety Notes
ALWAYS: · Connect to a grounded circuit. · Connect to operating voltages as
specified on the product’s spec sticker. · Disconnect from power before
replacing the fuse. · Disconnect from its power source during periods of
inactivity. · Use a safety cable when suspending overhead. · Heed all
restrictions and warnings on the spec sticker. · Mount in a location with at
least 20 in (50 cm) of ventilation. · Replace the fuse with the same type and
rating.
In the event of a serious operating problem, stop using immediately. DO NOT:
· Open this product or attempt any repairs. It contains no user-serviceable
parts. · Look at the light source when the product is on. · Use if the power
cord is crimped or damaged. · Disconnect by pulling on the power cord. · Allow
flammable materials close to the product when it is operating. · Touch the
housing when it is on. · Block any ventilation holes/slots in the housing. ·
Connect to a dimmer or rheostat. · Carry the product by its power cord. ·
Operate in temperatures higher than 104°F (40°C). · Expose to environments
that exceed the Ingress Protection (IP) rating. · Expose to rain or moisture.
· Use outdoors. · Submerge. · Expose to corrosive environmental conditions
such as temperature, humidity, salinity,
pressure, radiation, or shock. · Set this product on a flammable surface.
Battery Charge Notes
Rechargeable lithium-ion batteries are potentially hazardous and can present a
serious FIRE HAZARD, SERIOUS INJURY and/or PROPERTY DAMAGE if damaged,
defective, or improperly used.
ALWAYS: Charge using a manufacturer-provided charger while the product is
powered off. Charge the battery in temperatures between 32°95°F (0°35°C).
Allow a depleted battery to charge for a few minutes before turning on the
product. If the battery is completely discharged, the device cannot be turned
on immediately when the charger is connected. Keep at least 3 ft (1 m)
distance to any heat source and away from flammable materials. Keep the lid of
any charging case open while charging. Keep batteries away from children.
Store batteries between 4060% charge. Follow local regulations when disposing
of batteries. Replace with an authentic Chauvet battery.
DO NOT: Continue charging if the battery becomes hot, smokes, swells, or gives
off an odor during charging. Leave the product unattended while charging.
Deplete the battery below 10%. Charge the battery in a closed container.
Charge for more than 24 hours.
Intimidator Free Spot 60 ILS User Manual Rev. 2
2
Before You Begin
FCC Statement of Compliance
This device complies with Part 15 Part B of the FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
· Reorient or relocate the receiving antenna. · Increase the separation
between the equipment and receiver. · Connect the equipment into an outlet on
a circuit different from that to which the receiver is
connected. · Consult the dealer or an experienced radio/TV technician for
help. Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
RF Exposure Warning for North America and Australia
Warning! This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20 cm between the radiator and the user.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Disclaimer
Chauvet believes that the information contained in this manual is accurate in
all respects. However, Chauvet assumes no responsibility and specifically
disclaims any and all liability to any party for any loss, damage or
disruption caused by any errors or omissions in this document, whether such
errors or omissions result from negligence, accident or any other cause.
Chauvet reserves the right to revise the content of this document without any
obligation to notify any person or company of such revision, however, Chauvet
has no obligation to make, and does not commit to make, any such revisions.
Download the latest version from www.chauvetdj.com. The works of authorship
contained in this manual, including, but not limited to, all designs, text,
and images are owned by Chauvet. © Copyright 2023 Chauvet & Sons, LLC. All
rights reserved. Electronically published by Chauvet in the United States of
America. Chauvet, the Chauvet logo, and Intimidator Free Spot 60 ILS are
registered trademarks or trademarks of Chauvet & Sons LLC. (d/b/a Chauvet and
Chauvet Lighting) in the United States and other countries. Other company and
product names and logos referred to herein may be trademarks of their
respective companies.
Keep this User Manual for future use.
3
Intimidator Free Spot 60 ILS User Manual Rev. 2
Introduction
2. Introduction
Product Overview
USB slot
Fuse holder
Carry handle Display screen
Menu buttons
DMX in/out
Safety loop
Power in
Intimidator Free Spot 60 ILS User Manual Rev. 2
4
Product Dimensions
15.4 in 391 mm
Introduction
11.4 in 290 mm
11.9 in 301 mm
10.2 in 258 mm
5
Intimidator Free Spot 60 ILS User Manual Rev. 2
Setup
3. Setup
AC Power
The Intimidator Free Spot 60 ILS has an auto-ranging power supply, and it can
work with an input voltage range of 100 to 240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet,
and wiring), use the current value listed on the label affixed to the
product’s back panel or refer to the product’s specifications chart. The
listed current rating indicates the product’s average current draw under
normal conditions.
· Always connect the product to a protected circuit (a circuit breaker or
fuse). Make
sure the product has an appropriate electrical ground to avoid the risk of
!
electrocution or fire.
· To eliminate unnecessary wear and improve its lifespan, completely
disconnect the
product from power via breaker or by unplugging it during periods of non-use.
Never connect the product to a rheostat (variable resistor) or dimmer circuit,
even if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse Replacement
1. Disconnect the product from power. 2. Wedge the tip of a flat-head
screwdriver into the slot of the fuse holder. 3. Pry the fuse holder out of
the housing. 4. Remove the blown fuse from the holder and replace with a fuse
of the exact same type and rating. 5. Insert the fuse holder back in place and
reconnect power.
Installed fuse
(held by plastic clip)
Spare fuse holder
(inside safety cap)
Safety cap
!
· Disconnect the product from the power outlet before replacing the fuse. ·
Always replace a blown fuse with one of the same type and rating.
Battery Power
The Intimidator Free Spot 60 ILS comes with a rechargeable lithium battery for
cable-free operation.
Charging the Battery
The battery charges whenever the Intimidator Free Spot 60 ILS is plugged into
a power source using the included power cable. If the product is plugged in
and not in operation, make sure the product is turned off.
· Before charging the product, read and follow the safety recommendations in
the Safety Notes.
· The LED indicator light will flash if units are overcharged. · DO NOT use
the Intimidator Free Spot 60 ILS on full power mode while being
charged/plugged into a power source, as the unit will get extremely hot.
Battery Life Indicator
The numbers displayed on the battery indicator show how much battery life
remains available. The battery indicator will display up to four (+) signs
while charging.
100
Battery Run Time
In use
Maximum Run Time Up to 8 hours
Charging
Recharge Time 6.75 hours
Intimidator Free Spot 60 ILS User Manual Rev. 2
6
Setup
Mounting
Before mounting the product, read and follow the safety recommendations
indicated in the Safety Notes.
Orientation
The Intimidator Free Spot 60 ILS may be mounted in any position; however, make
sure adequate ventilation is provided around the product.
Rigging
· Before deciding on a location for the product, always make sure there is
easy access to the product for maintenance and programming purposes.
· Make sure adequate ventilation is provided around the product. · Mount the
product on a structure or surface that can support the product’s weight (see
the Technical
Specifications for weight information). · Always use a safety cable when
mounting the product overhead. Mount the product securely to a
rigging point (e.g., an elevated platform or a truss). · Use a mounting clamp
of appropriate weight capacity when rigging the product onto a truss.
Mounting Diagram
Mounting clamp
(such as CLP-15 or CLP-15N from Chauvet)
Omega bracket
Safety cable
(such as CH-05 from Chauvet)
7
Intimidator Free Spot 60 ILS User Manual Rev. 2
Operation
4. Operation
Control Panel Operation
To access the control panel functions, use the four buttons located next to
the display. Please refer to the Introduction to see the button locations on
the control panel.
Button Function
