ugee M808 Digital Drawing Tablet User Manual

June 15, 2024
UGEE

M808/M908
Digital Drawing Tablet
User Manual

Introduction

ugee M808 Digital Drawing Tablet -

Thank you for chosing ugee digital drawing tablet. To get the most out of this product and prolong its life, please read this manual carefully before use and follow the instructions for maintenance and protection of the product.
The appearance, color and accessories of the product may vary due to the latest product improvements. Please refer to the actual product. We reserve the right to upgrade the product technology and modify this manual without prior notice.
Note: All images in the manual are for illustrative purposes only. Please refer to the actual product.

Product Overview

ugee M808 Digital Drawing Tablet - Overview

  1. USB-C port

  2. Directional key(M808)/Wheel(M908)

  3.  Shortcut keys

  4.  Status shown by the white indicator:
    Flashing: The stylus is in the active area, but not touching the digital drawing tablet
    Steady on: The stylus is touching the active area
    Off: The stylus is outside the active area

  5. Active area

  6.  Lanyard hole

  7.  Stylus holder

Wired connection of the digital drawing tablet

ugee M808 Digital Drawing Tablet - usb cable

After connecting the digital drawing tablet to your computer via USB cable, check if you can use stylus to control the cursor.

Driver Download

Go to the ugee website (www.ugee.com) and download the driver for the appropriate operating system based on the product model you have purchased.
Notes:
Before installing the driver, turn off all antivirus software and graphics software.
Uninstall drivers (if any) of other brands digital drawing tablets/monitors before the installation.
For optimal experience, restart your computer after the installation is completed.
For the best performance for your device, we recommend you install the latest driver.

Driver Installation

5.1 Windows
Compatible with Windows 7 or later.
Unzip file. Run the “.exe” file as administrator, and follow the prompts to complete the installation.

ugee M808 Digital Drawing Tablet - Windows

5.2 Mac OS
Compatible with Mac OS X 10.12 or later.
After the download is completed, run the”.dmg” file. Follow the steps below to install the driver.

ugee M808 Digital Drawing Tablet - Windows1

5.3 Linux
Deb: Enter command “sudo dpkg -i”. Drag installation file to window and execute command.

ugee M808 Digital Drawing Tablet - Linux

Rpm: Enter command “sudo rpm -i”. Drag installation file to the window and execute command.

ugee M808 Digital Drawing Tablet - Linux1

Tag.gz: Unzip file. Enter command “sudo”. Drag “install.sh” to the window and execute command.

How to Use Driver

6.1 Connect to Device
The driver will run automatically after being installed. If it does not run automatically, go to the driver folder to run it manually.
Windows program path: Start→ugeeTablet
Mac program path: Application→UgeePenTablet→ugeeTablet
If the device is not connected or the connection fails, you will see the following prompt. In this case, restart your computer or the driver to connect it again or contact our service staff for support.

ugee M808 Digital Drawing Tablet - Connect to Device

If you have any questions about the connection, click the How to Plug in, Connection failed, or No signal for FAQs. If you can’t find a solution there, you can click Contact Us for customer service.
If the device is connected successfully, its product model will be displayed on the bottom right corner of the display, for example, M908 as shown in the image.
You can connect up to three devices via the driver at the same time. Click on drop-down menu to select device to activate. Customize the device’s settings after switching to that device. All changes apply only to that device.

ugee M808 Digital Drawing Tablet - switching

6.2 Pen Settings
6.2.1 Pen Shortcut Key
Click Mouse Control to customize key functions. You can select 7 types of shortcut keys, such as keyboard, mouse control, device, run application, system function, multimedia, and disable.

ugee M808 Digital Drawing Tablet - Shortcut Key

Keyboard:
Set keyboard shortcut, for example, set it as Alt+A in 3D MAX, so the alignment tool can be used.
Clear: Clear all combination keys in the input box
Delete: Delete the last combination key
Windows+: Upon clicking, you can continue to input with other key combinations.
For example, if you need to set Windows+Shift+S, you can click Windows+, and then manually press Shift+S to complete the setting.

ugee M808 Digital Drawing Tablet - Keyboard

Mouse Control:
Set mouse and key combination. For example, if you select Shift and Left Click, you can execute the assigned shortcut command if the software supports this combination key.

ugee M808 Digital Drawing Tablet - Keyboard1

Device:
Execute selected function.
Precision mode: It limits the Work Area to a small range. This function allows you to draw more precisely in the area.

ugee M808 Digital Drawing Tablet - Device

Run Application:
Run the selected application. For example, if you choose to run Photoshop, press the key, and the computer will open and run the app.

ugee M808 Digital Drawing Tablet - Run Application

System Functions:
Executes the selected system function. For example, select Shut Down, press the key, and the computer will automatically shut down.

ugee M808 Digital Drawing Tablet - System Functions

Multimedia:
Executes the selected multimedia function. For example, select Previous, press the key, and the computer will play the previous song.

ugee M808 Digital Drawing Tablet - System Functions1

Disable:
Upon the setting of no function, nothing will happen after pressing the key.

ugee M808 Digital Drawing Tablet - Disable

Mouse mode:
When you remove your pen, the cursor will stay where you left, which is like operating a mouse. Select the mode and you can adjust the speed of the cursor on your device. If no mode is selected, the pen mode will be applies by default.


Pen Pressure:
Upon unchecking, no stylus pressure effect will be displayed

Tilt:
Upon unchecking, there will be no tilt effect

Windows Ink (for Windows only):
Windows supports handwriting function. If you need to use this function in Microsoft Office/Whiteboard or other software, please do not turn it off.

6.2.2 Pen Pressure Settings
Pressure sensitivity can be adjusted by modifying the Pen Pressure curve or moving the slider on the progress bar.
Test your current pen pressure with Pressure Test.

ugee M808 Digital Drawing Tablet - Pen Pressure
Settings

6.3 Digital drawing tablet
6.3.1 Work Area Settings
Go to “Work Area” and define the mapping between the working area of the device and the display area of the screen.

6.3.1.1 Screen
If multiple monitors are used in copy mode, the Work Area of the device will be mapped to all monitors. When the pen moves in the Work Area, the cursor on all monitors will move at the same time.
If multiple monitors are used in extended mode, select one of the monitors on the tabs to map the working area of device.
There are two available options to set the monitor mapping area:

  1.  Dragging Four Sides: Move the cursor to the middle or ends of the four sides, then press and hold the left mouse button to drag the four sides;
    ugee M808 Digital Drawing Tablet - mouse button

  2. Screen Area Selection: Click Advanced Settings, then choose Screen Area Selection. Click the upper left corner and lower right corner according to prompts from the bottom of the computer monitor, and select the mapping display area of the screen.
    ugee M808 Digital Drawing Tablet - computer monitor

6.3.1.2 Digital drawing Tablet
You can set the Work Area of current device. The driver enables you to set the Work
Area of the device in the following ways:

  1. Dragging Four Sides: Move the cursor to the middle or ends of the four sides, then press and hold the left mouse button to drag the four sides.
    ugee M808 Digital Drawing Tablet - computer monitor1

  2. Handwriting Area Selection: Click Advanced Settings, then choose Select Handwriting Area. Click the upper left corner and lower right corner of the device using the stylus to select the handwriting area according to the prompts from the bottom of the computer monitor.

ugee M808 Digital Drawing Tablet - Handwriting Area

6.3.1.3 Screen proportion
Based on the screen proportion, you should make the working area of the device have the same proportion as that of the selected monitor’s entire display area. For example, if the screen proportion is 16:9, clicking the Screen proportion will adjust the working area to 16:9.
Note: Select Screen proportion and draw a circle on the device, then a circle will be displayed on the screen. But part of the device’s working area may not be available. If the Screen proportion is not selected, an

ugee M808 Digital Drawing Tablet - Handwriting Area1

ellipse may be displayed on the screen.

6.3.1.4 Advanced Settings
Select Screen:
When the computer is connected to a second screen, you can pull down to select the target screen to be mapped by the device

ugee M808 Digital Drawing Tablet - connected

Show monitor number:
Identify all connected monitors. The monitor number will be displayed in the lower left corner of each monitor.

ugee M808 Digital Drawing Tablet - corner

Set Screen Area:
You can manually select the working area of the screen according to the prompts from the bottom of the computer monitor. For details, see the Screen Area Selection setting in 6.3.1.1.

ugee M808 Digital Drawing Tablet - Set Screen Area

Rotation settings:
You can set the device to 0°, 90°, 180° or 270°. Rotate the device to the corresponding direction after setting rotation.

ugee M808 Digital Drawing Tablet - Set Screen Area1

Select Handwriting Area:
You can manually select the work area for handwriting according to the prompts. For details, see the Handwriting Area Selection setting in 6.3.1.2

ugee M808 Digital Drawing Tablet - handwriting

6.3.2 Shortcut Key Setting
The position and number of keys will differ due to product model. M908 is used here for illustrative purposes.
Upon selecting and pressing the target key, a pop-up window will show up, and you can customize key functions. You can select 7 types of shortcut keys, such as keyboard, mouse control, device, run application, system function, multimedia, and disable

ugee M808 Digital Drawing Tablet - Shortcut Key
Setting

Keyboard:
Set keyboard shortcut, for example, set it as Alt+A in 3D MAX, so the alignment tool can be used.
Clear: Clear all combination keys in the input box
Delete: Delete the last combination key
Windows+: Upon clicking, you can continue to input with other key combinations.
For example, if you need to set Windows+Shift+S, you can click Windows+, and then manually press Shift+S to complete the setting.

ugee M808 Digital Drawing Tablet - Keyboard tool

Mouse Control:
Set mouse and key combination. For example, if you select “Shift” and “Left Click”, you can execute the assigned shortcut command if the software supports this combination key.

ugee M808 Digital Drawing Tablet - Keyboard tool1

Device:
Execute selected function.
Precision mode: It limits the Work Area to a small range. This function allows you to draw more precisely in the area.

ugee M808 Digital Drawing Tablet - Keyboard tool2

Run Application:
Run the selected application. For example, if you choose to run Photoshop, press the key, and the computer will open and run the app.

ugee M808 Digital Drawing Tablet - app

System Functions:
Executes the selected system function. For example, select Shutdown, press the key, and the computer will automatically shut down.

ugee M808 Digital Drawing Tablet - app1

Multimedia:
Executes the selected multimedia function. For example, select Previous, press the key, and the computer will play the previous song.

ugee M808 Digital Drawing Tablet - Multimedia

Disable:
Upon the setting of no function, nothing will happen after pressing the key.

ugee M808 Digital Drawing Tablet - pressing the key

Wheel(Only M908):
Some device models are equipped with a roller function. The roller button will be displayed on the page of Shortcut Keys, which can be clicked to set the button’s value.
You can adjust the following four parameters:

  1. Zoom: zoom canvas
  2. Scroll: scroll canvas vertically
  3. Brush size: adjust brush size
  4. Rotate: rotate canvas

ugee M808 Digital Drawing Tablet - rotate canvas

Additionally, you can have the key value set as no function or customize the key value. Upon setting the clockwise and counterclockwise rotation, the key value can be customized respectively.

ugee M808 Digital Drawing Tablet - clockwise

6.4 Driver Settings

ugee M808 Digital Drawing Tablet - Driver Settings

Prompt Message:
In the off state, the key status will not be displayed at the bottom of the screen as the device and stylus keys are being used.

ugee M808 Digital Drawing Tablet - Driver Settings1

Enable Shortcut Keys:
In the off state, the functions of all keys on the device are disabled.

ugee M808 Digital Drawing Tablet - Enable Shortcut
Keys

Import config:
You can import configured shortcut keys and other functions.

ugee M808 Digital Drawing Tablet - Import config

Export config:
Export saved settings in a configuration file. A pop-up window will appear to notify you when the configuration file is exported successfully.

ugee M808 Digital Drawing Tablet - configuration

Diagnostic tool:
If you encounter any issues while using the driver, please use the diagnostic tool to check hardware/environmental data for troubleshooting. If you approach our customer/technical support, this data will also be helpful for our staff to assist you.

ugee M808 Digital Drawing Tablet - Diagnostic tool

Default:
Upon clicking, the values of shortcut keys, work area, display settings, and other settings will all be restored to the default values

ugee M808 Digital Drawing Tablet - default values

Video Tutorials:
Upon clicking, you will be directed to the Video Tutorials page through the computer’s browser

ugee M808 Digital Drawing Tablet - Video Tutorials

View User Manual:
Upon clicking, you will be directed to the Search Model page of the official website through the computer’s browser

ugee M808 Digital Drawing Tablet - Video Tutorials1

Upon clicking, you will be directed to the FAQ link on the official website through the computer’s browser

ugee M808 Digital Drawing Tablet - FAQ link

6.5 Applications and Others
6.5.1 Add Application
Click the “+” icon on the upper right corner to add application.

ugee M808 Digital Drawing Tablet - FAQ link1

Select the application from the list of installed applications or click “Browse” and select the application path.

ugee M808 Digital Drawing Tablet - Browse

Next, click OK to add selected application.

ugee M808 Digital Drawing Tablet - Browse1

6.5.2 Delete Application
Click on the drop-down menu and select the application. Then click on the “x” on the top right corner to delete the application.

ugee M808 Digital Drawing Tablet - Delete Application

Uninstallation

7.1 Windows
Go to Start -> Settings -> Apps -> Apps & Features, find “ugeeTablet” and then left-click “Uninstall” as per prompts.
7.2 Mac OS
Go to Go to -> Application and locate ugeeTablet. Click on “UgeeTabletUninstall” and follow the prompts to uninstall.
7.3 Linux
Deb: Enter command “sudo dpkg -r ugee-pentablet” and execute the command. Rpm: Enter command “sudo rpm -e ugee-pentablet” and execute the command.Tag.gz: Unzip file. Enter command “sudo”. Drag uninstall.sh to the window and execute command.

FAQs

8.1 Pen pressure seems to be disabled

Check if the drawing software supports pen pressure. Please download the latest driver from ugee website, and check if the pen pressure is normal. Before installing the driver, turn off your antivirus and graphics software. Uninstall drivers for other drawing displays before installation. Restart your computer after the installation is completed; If the pen pressure is normal (Windows: ensure Windows Ink is enabled in the pen settings of the driver), restart the drawing software for testing.

8.2 Delay and stagnation in painting

Check if the computer meets the recommended configuration (CPU&GPU) requirements for the drawing software installed, and optimize related functions via Settings according to the useful FAQs posted on the official website of the drawing software in use.

8.3 My computer doesn't recognize the device

Check if your computer's USB port works normally; if not, use another USB port.

8.4 My stylus is not working

Check if it is the matching stylus for the device. Install driver and check if the pen settings are functioning properly.

If you encounter an issue with your product, please check our FAQs at
https://www.ugee.com/faq to see if then can help。
lf you need any further assistance, please contact us:
E-mail: service@ugee.com
Web: www.ugee.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals