TOPSKY TS500032 Triple-Motor Electric Adjustable Standing and Sitting Computer Desk Instruction Manual

TOPSKY TS500032 Triple-Motor Electric Adjustable Standing and Sitting

Computer Desk

How to contact with us
Email: service@topskyfurniture.com
Customer Service Phone: +1 725-333-1988
http://www.topskyfurniture.com

Caution

• Keep children and pets away from the electric height-adjustable desk during the operation. Unplug the power cord during a thunderstorm or if you do not intend to use the desk for a long time.
• Make sure desktop not touching the wall.
• Ensure no obstacles in the desk’s path and no object above and 20” under the desk.
• Working environment temperature 0-40℃, keep products away from corrosive gas, liquid and dusty objects.
• It is strictly forbidden to disassemble the products privately to avoid that the failure of the products or the damage to the human body caused by electronic products, etc.
• Although the product with anti-collision function, in order to avoid any pinching, please ensures that hands or other parts of your body are in a safe position during the operation. Anti-collision is not enabled during all resets.
• Please read the following instructions carefully before start using the highadjustable desk. The company does not bear any warranty or liability for damage and human injury caused by any abnormal operation.
• It is necessary to reset manually after the initial installation or power off.

Parts List

Tools Needed (Not Included)

Assembly

Instruction

Manual Reset
It is necessary to be reset manually after the initial installation and power off.

1.  rES Keep pressing down key till the desktop till display shows“E-1”and“rES” alternately and release the key.
2. 27.6 Keep pressing down key again, the desktop will move slowly down and return back till the display shows“27.6”.
3. Release the key, the height-adjustable desk resetting finished.

Note: The anti-Collision function is not enabled during all resets. Please note that there is a potential risk of pinching in this case, and be sure no obstacles in the desk’s path.

Up and Down

1. Keep pressing“up”key till the required height is reached.
2. Keep pressing“down”key till the required height is reached.

Saving position

1. ▲ Adjust the desktop to the height you want to save.
2. M Keep pressing“M”key till the display will show“S–”.
3. 1 Press“1”key, the display will show“S-1”and the current height alternately.
4. M Press“M”key，the first memory position is set successfully. Similar procedure for“2”key and “3”key memory positions.

High and Low Limitation Positions
Do not enable this function unless you are really need in some situation.

1. M Keep pressing the key“M”till the display shows“S–”.
2. ▲ HLP Press“up”key till the display flash as“HLP”.
3. 1 H-P Press“1”key, the display show alternately as“H-P”and current height.
4. ▲ Keep pressing“up”or“down”key till the required high limit position is reached.
5. M Press“M”key, the desktop height will be showed and the high limit position has been set.
6. 2 L-P Repeat step 1 and step 2 , then press“2”key, the display will show“L-P” and current height alternately, keep pressing“down”key till the low limit position is reached, press“M”key, the low limit position has been set.

Note: By this function would be used to limit the movement area of desktop, when the container is underneath or any shelf above the desktop. Once it is set, the new high or low limitation
position will be stored.

Change the displayed Unit（cm/inch）

1. M Keep pressing key“M”till the display shows“S–”.
2. ▲ Unt Press“up” key, the display will show“Unt”.
3. 1 Press“1”key, the display will show“Unt”and the current height alternately, and the unit of height is“cm”.
4. M Press“M” key to save the unit as“cm”.
5. 2 M Repeat step 1 and step 2 , then press“2”key, the display shows“Unt” and the current height alternately, and the unit of height is“inch”, press “M”key to save the unit as“inch”.

Amend the desktop height displayed
Before operating this function, execute the Manual Reset procedure.

1. M Keep pressing key“M”till the display shows“ Ur”and “Off”alternately.
2. ▲ Press“up”key till the display shows“End”and current height alternately. ( for metric, please note that the unit is“mm”during this procedure)
3. 1 2 3 Changing the height by pressing“1”key to adjust the first number,“2” key to adjust the second number, and“3”key to adjust the third number.
4. M Press“M”the height has been changed to defined digit.

Note: The function enables you to change the height shows on the display based on the actual measurement.

Anti-Collision function

• Once the desktop encounters any obstacle in its path, the screen displays“E-2”。
• The desktop will move a defined distance in opposite direction, and it would be used normally after removing the obstacle.

Plug detection
The function can detect whether the motors are collected normally

1. E-3 rES Once the display shows“E-3”and“rES”，it reminds you check whether any motors fail connected with control unit. Please connect the main cable again,wait at least 5 seconds.
2. Connect all the plugs.
3. rES Follow “Manual Reset ”procedure.

Restore factory setting
With this functin,you can make the control unit to factory setting.

1. M Keep pressing“M”till the display shows“FAC”.
2. M Press“M”,and the control unit restore to factory setting (including memory position, high and low limitation positions, etc).

Code meaning and Troubleshooting

/ 122KG for further operation
E-2| Anti-Collision function| It can be used normally after removing the obstacle
dut| Operated continuously without suitable rest| Make the desk rest around 18minutes for further operation

Troubleshooting

to Manual reset
E-3| Check the cables and ensure they are well connected, and the height- adjustable desk can be used normally after manual reset

Technical Data

References

• TOPSKYFURNITURE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>