Infinix X695 Note 10 Pro 128GB 8GB Dual Sim Smart Phone User Manual

June 6, 2024
Infinix

Infinix-X695-Note-10 Pro-128GB-8GB-Dual-Sim-Smart-Phone-FI
LOGO

Infinix X695 Note 10 Pro 128GB 8GB Dual Sim Smart Phone

EXPLOSION DIAGRAM SPECIFICATION

1 FL(CTP+LCM 2 fornt housing Assembly
3 PCBA Main 4 Front Camera
5 Back Camera 6 Back Camera
7 REC Deco part 8 F CAM Cop foil
9 LT sensor diffuse film 10 M1.4xL3.5 SCREW
11 REC con fb 12 LT sensor Seal rubber
13 Fornt CAM rubber 14 M1.4xL2.5 SCREW
15 SPK 16 UP frame asm
17 Bat cover asm 18 MAIN seal mylar
19 Rear CAM Lens 20 Fingerchip spacer
21 Shield Imp foam 22 Bat con rubber
23 LCM FPC con rubber 24 FP con imp steel asm
25 trope fill foam 26 R trope foam B
27 FPC Side key 28 PCBA SUB
29 Moto 30 Battery
31 USB Seal rubber 32 Audio Jack Seal rubber
33 SUB PCB BTB Rubber 34 coaxial cable
35 SPK frame asm 36 3in1 card holder
37 R CAM Con foams 38 Audio cavity seal mylar
39 Shield Seal Cop foil 40 FP Con Foams
41 FP support foam 42

Know your phone

  1.  Front camera
  2.  Volume + key
  3.  Volume – key
  4.  Power key & side fingerprint sensor

SIM/SD card installation

  1.  Power off the mobile.
  2.  Refer to the following picture for SIM / SD card installation.

Charging the phone

You can charge your device using a charger or by connecting it to the computer using a USB cable (comes with the phone).

  1.  Please remind the front and back of the plug.
  2.  Use only an INFINIX charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty.

FCC Caution

Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Information to the user.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  •  Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  •  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  •  Consult the dealer or an experienced radio/TV technician for help.

Specific Absorption Rate (SAR) information:
This mobile phone meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluations of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement The SAR limit of the USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: X695 (FCC ID: 2AIZN-X695) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.14W/kg and when properly worn on the body is 1.19W/kg. This device was tested for typical body-worn operations with the back of the handset kept 10mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10mm separation distance between the user’s body and the back of the handset. The use of belt clips, holsters, and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements and should be avoided.

Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS, and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved. Operating System: AndroidTM Android is a trademark of Google LLC.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals