elk HOME 89679-8 Eight Light Chandelier Installation Guide

elk HOME 89679-8 Eight Light Chandelier

Product Information

Specifications:

• Item Number: 89679/8
• Junction Box: A
• Ground Screw: E
• Threaded Pipe: W
• Canopy: D
• Stems: M-12, N-6

Product Usage Instructions

Installation

1. Disconnect power at the main fuse box before installation.
2. This fixture is intended for installation by the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.
3. Before assembly, remove all parts and part packages from the box. If anything is missing, please get in touch with the retailer from which the product was purchased.
4. Carefully pull house wires down out of the junction box so house wires are easily accessed to connect fixture wires.
5. Position mounting bracket (A) so the head of the ground screw and longer end of the threaded pipe (W) is pointing down towards the floor. Place mounting bracket (A) up against the junction box. Align each slot in mounting bracket (A) with each hole in the junction box.
6. Thread one junction box screw (B) into each slot in the mounting bracket (A) and into holes in the junction box. Tighten junction box screws (B) to secure mounting bracket (A) to the junction box.
7. Thread screw collar (E) with swivel (W) onto the end of the threaded pipe attached to mounting bracket (A). CAUTION: Make sure house wires are still easily accessible. DO NOT pinch wires between the mounting bracket and ceiling.
8. Slip ring (P) onto the end of the center stem in between arms. Thread the finial (L) onto the end of the center stem. Tighten finial (L) to secure ring (P) in place.
9. Determine the desired hanging height of the fixture. Select the quantity of stems (M-12, N-6) to achieve that height.
10. Carefully push fixture wires through stems (M/N). Thread the stem to the top of the fixture body (O). DO NOT pinch fixture wires between stems.
11. Slip threaded ring (F) down over the end of the last stem.
12. Position canopy (D) so the outside of the canopy is pointing down towards the fixture. Slip the hole in canopy (D) over the end of the stem.

Wire Connections

10. Strip 3/4 of insulation from the ends of fixture wires.
11. Carefully push fixture wires up through the hole in swivel (W) attached to screw collar (E) and out the end-threaded pipe inside the junction box. Carefully pull fixture wires so they are easily accessible to connect to house wires.
12. Thread the end of the last stem (M) onto swivel (W). DO NOT pinch wires between stem (M) and swivel (W).
13. Slightly loosen the ground screw on the mounting bracket (A). Do not completely remove the ground screw. Wrap house ground wire (copper) around ground screw, leaving enough ground wire to attach to fixture ground wire. Twist the end of the fixture ground wire and the end of the house ground wire (copper) together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference the chart below for correct wire connections.
14. Twist the end of the house lead wire (black) and the end of the fixture lead wire (black) together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Twist the end of the house neutral wire (white) and the end of the fixture neutral wire (white) together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C).

FAQ

• Question: What do I do if any parts are missing?
  Answer: If anything is missing, please get in touch with the retailer from which the product was purchased.

• Question: How should I connect the supply (house) ground wire?
  Answer: Wrap the house ground wire (copper) around the ground screw on the mounting bracket (A), leaving enough ground wire to attach to the fixture ground wire. Twist the end of the fixture ground wire and the end of the house ground wire (copper) together. Twist wire nut (C) onto ends of the wires. Completely tighten wire nut (C). Reference the chart for correct wire connections.

WARNING :
DISCONNECT POWER AT THE MAIN FUSE BOX BEFORE INSTALLATION.

WARNING:
This fixture is intended for installation by the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended. Before assembly, remove all parts and part packages from box. If anything is missing, please get in touch with the retailer from which the product was purchased.

INSTALLATION

1. Carefully pull house wires down out of the junction box so house wires are easily accessed to connect fixture wires.
2. Position the mounting bracket so the head of the ground screw and longer end of the threaded pipe is pointing down towards floor. Place mounting bracket (A) up against junction box. Align each slot in mounting bracket (A) with each hole in the junction box.
3. Thread one junction box screw (B) into each slot in the mounting bracket (A) and into holes in junction box. Tighten junction box screws (B) to secure mounting bracket (A) to the junction box.
4. Thread screw collar (E) with swivel (W) onto end of threaded pipe attached to mounting bracket (A). CAUTION: Make sure house wires are still easily accessible. DO NOT pinch wires between the mounting bracket and ceiling.
5. Slip ring (P) onto the end of the center stem in between arms. Thread finial (L) onto end of center stem. Tighten finial (L) to secure ring (P) in place. .
6. Determine the desired hanging height of the fixture. Select the quantity of stems (M-12″, N-6″) to achieve that height.
7. Carefully push fixture wires through stems (M/N). Thread stem to top of fixture body (O). DO NOT pinch fixture wires between stems.
8. Slip threaded ring (F) down over end of last stem.
9. Position canopy (D) so the outside of the canopy is pointing down towards the fixture. Slip hole in the canopy (D) over the end of the stem.
10. Strip 3/4” of insulation from ends of fixture wires.
11. Carefully push fixture wires up through hole in swivel (W) attached to screw collar (E) and out-end threaded pipe inside the junction box. Carefully pull fixture wires so they are easily accessible to connect to house wires.
12. Thread end of last stem (M) onto swivel (W). DO NOT pinch wires between stem (M) and swivel (W).

13. Slightly loosen the ground screw on the mounting bracket (A). Do not completely remove ground screw. Wrap house ground wire (copper) around the ground screw, leaving enough ground wire to attach to fixture ground wire. Twist end of fixture ground wire and end of the house ground wire (copper) together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Reference the chart below for correct wire connections.
    Connect Supply (House) Ground Copper Wire to:

    Bare Copper Wire or,
    Bare Silver Wire or,
    Green Insulated Wire.

14. Twist end of the house lead wire (black) and end of fixture lead wire (black) together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C). Twist end of house neutral wire (white) and end of fixture neutral wire (white) together. Twist wire nut (C) onto ends of wires. Completely tighten wire nut (C).
15. Wrap electrical tape (not included) around wire nuts (C) and wires. Ensure wires are securely fastened into wire nuts (C).
16. Carefully push all wires and wire nuts into junction box.
    Connect Black Lead Supply (House) Wire to:| Connect White Neutral Supply (House) Wire to:
    ---|---
    Black Wire or,| White Wire or,
    Parallel Cord (Round and Smooth) or,| Parallel Cord (Square and Ridged) or,
    No printed words on wire insulation or,| Printed words on wire insulation or,
    Insulated Wire (other than green)

with Copper Conductor.

| Insulated Wire (other than green)

with Silver Conductor.

*When parallel wire (SPT 1 & SPT 2) is used: The lead wire is round in shape or smooth.

The neutral wire is square in shape or ridged.

17. Raise canopy (D) up to ceiling. Pass hole in canopy (D) over screw collar (E). Position canopy (D) up against the ceiling.

18. Raise threaded ring (F) up to canopy (D). Screw threaded ring (F) onto screw collar (E). Tighten the threaded ring (F) to secure the fixture to the ceiling.

19. Screw recommended bulbs (E12 candelabra bulb type, not included) into sockets. Verify correct bulb wattage marked on the socket of the fixture.
    WARNING : DO NOT exceed maximum bulb wattage.

20. Carefully pass hole in shade (K) down over the bulb. Turn shade (K) clockwise to secure shade (K) in place. DO NOT over-tighten.

elkhome.com
ANY QUESTIONS CALL: 800-613-3261
M-F 8:00AM-6:00PM ET
ITEM#: 89679/8

References

• elkhome.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>