EZCast Q9R2 4K Ultra HD Wireless HDMI Transmitter and Receiver User Manual
- June 15, 2024
- EZCast
Table of Contents
EZCast Q9R2 4K Ultra HD Wireless HDMI Transmitter and Receiver
Product Information
Specifications
- Size: 100*57mm
- HD
- Ver. A 1.0
Product Usage Instructions
Connection Diagram
- Receiver-RX
- Function Button
- Indicator Light
- HD USB-C Power Supply Port
- HD Transmitter-TX
- Function Button Indicator Light
- USB-C Power Supply Port
- Hardware Casting Combination of receiver and transmitter, plug and play
Pairing Instructions
The product has been paired out of the factory. In case of pairing failure due
to improper operation or other circumstances during use, it is necessary to
restore and re-pair the device as follows:
Function Settings
- Search for a receiver in Wireless Network (Name is RX-XXXX, the default password is 12345678)
- Open the mobile/tablet browser and enter 192.168.203.1 in the address bar
- After entering the website, you can operate the distribution network, resolution, upgrade, and restart
Please make sure that the power of the computer is sufficient. If the power supply of the computer is insufficient or the HD is unable to supply power, please connect the transmitter to the power adapter or USB-C power supply port (Voltage above 5V, current above 2A)
Receiver[RX] – Function Button
Transmitter[TX] – Function Button
Transmitter Indicator Status
- Slow Flash: Disconnected
- Fast Flash: Pairing
- Always On: Connected
Pairing Instructions
- Please press the receiver function button for more than 3 seconds, and the prompt will pop up on the interface: Release the button to pair with Ezcast TX. Wait for the transmitter to enter pairing mode
- Press the transmitter function button for more than 5 seconds, the indicator will flash for pairing. Wait for the transmitter indicator to be always on, indicating that the connection is successful.
With one receiver and multiple transmitters, 1 receiver can pair with 8 transmitters for switching.
Problem-Solving
-
Q: How to restore factory settings?
A: When the product fails, press and hold the receiver function button for 10 seconds. After a black screen appears and restarts, the factory settings will be restored. -
Q: Can devices without HD interface be used?
A: Yes, please use the device with an HD interface converter. -
Q: How to enter privacy mode?
A: Tap the transmitter function button to disconnect or reconnect.
Preface
Thank you for purchasing the products, For optimum operation, please read this manual carefully before use.
Connection Diagram
Receiver-RX
Transmitter-TX
Hardware Casting
Combination of receiver and transmitter, plug and play
- Connect the HD port of the receiver to the video input port of the display device such as the monitor or TV.
- Connect the USB-C power supply port of the receiver to the charging cable and plug it into the power adapter ( Voltage above 5V, current above 2A). Turn on the Receiver power switch.
- Adjust the HD Signal source of the monitor or TV to the corresponding HD port until the boot screen is displayed.
- Connect the transmitter to the computer or other devices With HD video output function. After the indicator Light enters the fast flash state, Wait for ten seconds to complete Casting.
Please make sure that the power of the computer is sufficient. If the power supply of the computer is insufficient or HD is unable to supply power , please connect the transmitter to the power adapter or USB-C power supply port ( Voltage above 5V, current above 2A).
Pairing Instructions
The product has been paired out of the factory. In case of pairing failure due to improper operation or other circumstances during use, it is necessary to restore and re pair the device as follows:
- Please Press the receiver function button for more than 3 seconds, and the prompt will pop up on the interface: Release the button to pair With Ezcast TX. Wait for the transmitter to enter pairing mode
- Press the transmitter function button for more than 5 seconds, the indicator will flash for pairing, and Wait for the transmitter indicator to be always on, indicating that the connection is successful.
With one receiver and multiple transmitters, 1 receiver can pair with 8 transmitters for switching.
Function Settings
- Search for a receiver in Wireless Network (Name is RX-XXXX, the default password is 12345678)
- Open the mobile/tablet browser and enter 192.168.203.1 in the address bar
- After entering the website, you can operate the distribution network, resolution, upgrade, and restart
Problem-solving
-
Q: How to restore factory settings?
A: When the product fails, press and hold the receiver function button for 10 seconds. After a black screen appears and restart, the factory settings will be restored. -
Q: Can devices without an HD interface be used?
A: Yes, please use the device with an HD interface converter. -
Q: How to enter privacy mode?
A: Tap the transmitter function button to disconnect or reconnect.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>