EZCast QuattroPod USB Cross-Platform Wireless Solution User Guide
- June 6, 2024
- EZCast
Table of Contents
Quick Start Guide
What’s in the box?
Standard Package 
QuattroPod Receiver
Transmitter Operation
Transmitter
| Side button(Control button) | Host | Guest |
|---|---|---|
| Single click | Allow guest to mirror | – |
| Double click | Deny request | – |
| Hold for 3 seconds | Quit all display | – |
Working mode LED indication
LED indication during casting (Side button)
| Green On: Host mode
---|---
Read On: Guest mode
Green Blinking: Receiving cast request
Red Blinking: Sending cast request
LED indication for pairing (Side button)
| Red blinking: Pairing
---|---
Off: Pairing is done
LED indication for FW OTA (Side button)
| Red blinking: Upgrading FW
---|---
Off: Upgrade finished
Please pay attention to the following items while operating our products:
- Keep the product away from water
- Please do not open or repair it by yourself
- Please use the attached enclosures only
- Do not put or install the product under direct sunlight
- Do not use it on stormy days
- Prevent this product from falling, dropping, or crashing
- Do not cover or block the vent of the product
- Keep the ambient temperature under 40 degrees while operating
- Keep products away from the high humid environment
- Make sure all cables are connected correctly before turning on the power
- Prevent all cables, adapters, and products from being stepped and squeezed
- If you need to clean the surface of the product, please unplug the power and use a piece of clean&dry cloth
QuattroPod Transmitter
PC/Laptop
Type-C mode
Switch to Type-C mode and connect to your PC. Your screen will be cast after
QuattroPod USB’s WiFi connection is established.
- please make sure your PC supports Type C display
PC/Laptop
Type-A mode
Switch to Type-A and plug into your PC, a CD-ROM will pop up. Find “USB WiFi
Cast” for macOS or “USB Launcher” for Windows and install it.
- Mac users must allow privacy for screen recording
LOS
( Mobile Phone )
Switch to Mobile mode and convert to USB Type-A head for USB 5V power.
Android
( QuattroPod Apk )
- Please install the “QuattroPod” apk from GooglePlay or from our receiver
- Connect your WiFi to the receiver
- Open the QuattroPod apk, discover the receiver, and click it
- Once it’s connected, the LED will be turned on and you can cast it now.
( Chromecast )
- Connect your WiFi to the receiver
- Open the browser and input 192.168.168.1, Log-in as admin, and turn on Chromecast in the web setting
- Make sure our receiver is connected to the internet (via LAN or WiFi)
- PC: Open chrome browser and select cast to our receiver
- Phone: Open Google Home and find the receiver to mirror
Please enable USB Debugging before using.
-
Go to Setting ♦ System About Phone
-
Click Build Number 7 times to enable Developer Option
Kernel version
4.4.88-gb86ddObc9690 (Android clang version 5.0.300080 (based on LLVM 5.0.300080)) android-build@wpra8.hot.corp.google.com Wed Nov 8 06:19:15 UTC 2017
-
Go to Developer option -■ USB Debugging -, On
-
Plug to QuattroPod Transmitter and Allow USB debugging
* Note: Please select MTP or File Transferring in the notifications when USB is connected.
Pairing
The QuattroPod USB was paired before shipment so you can use it directly.
However, if you purchase another one you will need to do a pairing prior to
using it.
• Note: Due to Type-C / Mobile and Type-A being different working modes,
you might need to pair both Type C and Type A modes.
Type-C and Mobile mode
- Convert to USB Type-A head, switch working mode to Type-C and plug to QuattroPod Receiver. You will see the pairing progress on-screen or check the side button LED blinking.
- Once it s done, the side button LED will be off. You can unplug it or switch to another mode for pairing again.
Type-A mode
- Convert to USB Type-A head, switch working mode to Type-A and plug to QuattroPod Receiver’s USB port. You will see the pairing progress on-screen or check the side button LED blinking.
- The screen will show status once it s done, and QuattroPod USB s side button LED will be off. You can unplug it or switch to another mode for pairing again.
FCC STATEMENT
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement The device has been tested and complies with FCC SAR limits.
www.ezcast.com
02018 Actions Microelectronics Co., Ltd. All right reserved. Quattro Pod or
Quattro are trademarks of Actions Microelectronic Co., Ltd., registered in
China and other countries. Other product and company names mentioned herein
may be trademarks other respective companies. 02018 Actions Microelectronics
Co., Ltd.: Quattro! Quattro Pod Actions