BLAUPUNKT AMP1604 1600W 4 Channel Full Range Amplifier Instruction Manual
- June 15, 2024
- Blaupunkt
Table of Contents
AMP2002
AMP1604
AMP1500M
AMP3000D
High Power Amplifier
Instruction Manual
Enjoy it.
System Planning
System Planning Proper system planning is the best way to maximize your amplifier’s performance. By planning your installation carefully, you can avoid situations where the performance and reliability of your system is compromised. Our authorized dealer has been trained to maximize your system’s sound quality when installing the amplifier, and is a valuable resource in helping you with your system’s design and installation.
System Requirements
Each channel of your amplifier can easily handle 4Ω speaker loads when used in Stereo Mode. When a channel-pair is bridged, the recommended minimum load impedance is 3Ω for subwoofer use, and 4Ω for full-range operation. Although operation with lower impedances is not likely to cause immediate damage to the internal circuitry, the unit will most likely overheat, causing the thermal protection circuitry to shut down the amplifier. When the chassis cools down, normal operation will resume.
Continuing to operate the amplifier under these conditions is not recommended
and will reduce its life expectancy. Most speakers designed for car audio
operation are 4Ω impedance. Connecting two such speakers in parallel will
result in a 2Ω nominal impedance, which is not recommended for use with
bridged channels of your amplifier.
Connection Diagram
WARNING
Before beginning, DO NOT connect the car battery’s negative poles to the
positive m Sat short-circuitry might cause damage to your amplifier and other
electrical parts in the car.
System 1: 2-Channel Mode
system 2: Brdge Connection Subwoofer
Specifications
AMP2002
| RMS Output Power 2Ω (Watts) | 280Wx2 CH |
|---|---|
| RMS Output Power 4Ω (Watts) | 180Wx2 CH |
| Bridged Output Power 4Ω (Watts) | 600Wx1 CH |
| THD | <=0.05% |
| Frequency Response(+2dB) | 10Hz ~ 30KHz |
| Signal to Noise Ratio | =>96dB |
| Sensitivity | 200mV ~ 8V |
| Recommended Fuse Type | 25AXx2 |
| Dimensions | 11x 7.4 x 2.2 in |
System 1: 4-Channel Mode
System 2: Bridge Connection Subwoofer
Specifications
AMP1604
| RMS Output Power 2Ω (Watts) | 150Wx4 CH |
|---|---|
| RMS Output Power 4Ω (Watts) | 100Wx4 CH |
| THD | <=0.05% |
| Frequency Response(±2dB) | 10Hz ~ 30KHz |
| Signal-to-Noise Ratio | =>96dB |
| Sensitivity | 200mV ~ 8V |
| Recommended Fuse Type | 25Ax2 |
| Dimensions | 11x 7.4.x 2.2in |
System 1: Connection Subwoofer
System 2: Connection Subwoofer
Specifications
AMP1500M
| RMS Output Power 2Ω (Watts) | 800Wx1 CH |
|---|---|
| RMS Output Power 4Ω (Watts) | 400Wx1 CH |
| THD | <=0.05% |
| Frequency Response(±2dB) | 10Hz ~30KHz |
| Signal-to-Noise Ratio | =>96dB |
| Sensitivity | 200mV ~ 8V |
| Recommended Fuse Type | 30A x 1 |
| Dimensions | 8.7X7.4×2.2 in |
System 1: Connection Subwoofer
System 2: Connection Subwoofer
Specifications
AMP3000D
| RMS Output Power 2Ω (Watts) | 1600Wx1 CH |
|---|---|
| RMS Output Power 4Ω (Watts) | 800Wx1 CH |
| RMS Power 1 (Watts) | 2250Wx1 CH |
| THD | <=0.05% |
| Frequency Response (±2dB) | 10Hz-250Hz |
| Signal-to-noise ratio | =>96dB |
| Sensitivity | 200mV-8V |
| Recommended Fuse Type | 40A x3 |
| Dimensions | 11x 7.4x 2.2 in |
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No Output | Low or no remote turn-on input | Check remote turn-on voltage output |
on amplifier and correct as needed
Fuse down| Check power wire integrity and reverse polarity; repair as needed
and replace fuse
Power wires not connected| Check power wire connections and repair/replace as
needed
Audio input not connected or no output from source| Check input connections
and signal integrity; repair/replace as needed
Speaker wires not connected| Check speaker wires and repair/replace as needed
Audio cycles on and off| Speakers are blown| Check system with known working
speaker and repair/replace speakers as needed
Thermal protection engages when amplifier heat sink temperature exceeds 90°C|
Make sure there is proper ventilation for amplifier and improve ventilation as
needed
Loose or poor audio input| Check input connections and repair/replace as
needed
Distorted output| Amplifier level sensitivity set too high, exceeding maximum
output capability of amplifier| Reset gain. Refer to the turning section of
the manual for detailed instructions
Impedance load to amplifier too low| Check speaker impedance load. If below 20
stereo or 411 mono, rewire speakers to achieve a higher impedance
Shorted speaker wires| Check speaker wire connections and repair/replace as
needed
Speaker incorrectly connected to amplifier properly| Check speaker wiring and
repair/replace as needed. Refer to the installation section of this manual for
detailed instructions
Speakers are blown| Check system with known working speaker and repair/replace
as needed
Simple Troubleshooting
| Problem | Possible Cause | Soluticr |
|---|---|---|
| Poor Bass Response | Speaker polarity may be reversed or wired incorrectly, | |
| causing cancellation at low frequencies. | Check speiker polarity and repair as |
needed.
Crossover set incorrectly| Reset crossover. For detailed instructions, refer
to the multi-cross crossover configuration section of this manual
Battery Fuse Blowing| Impedance load to amplifier is too low| Check speaker
impedance load. If below 20 stereo or 40 mono, rewire speakers to achieve a
higher impedance
Short in power wire or incorrect power connection or wire| Check power and
ground connections and repair as needed
Fuse used is smaller than recommended| Replace with proper fuse size
Check speaker impedance load. If below 20 stereo or 40 mono, rewire speakers
to achieve a higher impedance and replace with recommended fuse size
Amplifier Fuse Blowing| Too much current being drawn| Check speaker impedance
load. If below 20 stereo or 40 mono, rewire speakers to achieve a higher
impedance and replace with recommended fuse size
Check power and ground connections. Repair as needed
Fuse used is smaller than recommended| Replace with proper fuse size
Shaghal Ltd. | 2231 Colby Ave, Los Angeles California 90064
©2020 BLAUPUNKT. All Rights Reserved. This device complies with part 15 of the
FCC Rules.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
WARNING: Cancer and Reproductive Harm –
www.P65Warnings.ca.gov
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>