Tenda TEG5328P-24-410W L3 Managed PoE Switch Installation Guide
- June 4, 2024
- Tenda
Table of Contents
Tenda TEG5328P-24-410W L3 Managed PoE Switch Installation Guide
Package contents
- Switch x 1
- Power cord x 1
- Console cable x 1
- L-shaped bracket x 2
- Screw x8
- Footpad x4
- Quick installation guide x 1
This quick installation guide instructs how to install, connect and log in to the device. For details, please download the user guide of the device.
1 Device installation
Installation notes
Follow the notes below to avoid device damages or personal injuries caused by mis operation.
- Wear the ESD bracelet or gloves before Installation and do not power on the switch before finishing installation.
- Use the included power cord to supply power to the switch.
- Make sure that the Input voltage matches the value of the switch specified in this guide.
- Do not block any ventilation openings.
- Do not remove the housing of the switch.
- Keep the air In the ambient environment clean. Regularly perform dedusting.
- Disconnect the switch from the power supply before cleaning it. Do not scrub the switch with any liquid. Clean only with dry cloth.
- Position the switch away from power line, electric lamp, or power system.
- Do not place any heavy things upon this switch.
- If outdoor cabling is required, you are recommended to deploy a port lightning arrester (see the following figure for connection method) or AC power supply lightning arrester.
Note
There is a void sticker covering one of the screws on the housing of the
switch. Do not remove the sticker without permission of the local agent.
Otherwise you shall be responsible for any damage.
Installation tools
- Desktop mounting: ESD bracelet (or gloves)
- Rack mounting: ESD bracelet (or gloves), Phillips screwdriver, Screws
Installation
■ Rack mounting
Step 1 Ensure that the subrack is stable and level, and is properly grounded.
Step 2 Fix L-shaped brackets to the switch with screws. See the following
figure.
■ Desktop mounting
Paste the four footpad stickers to the corresponding four recesses on the
bottom of the switch. Then place the switch right-side up on a big enough,
clean, stable and flat desktop.
Grounding
Step 1 Connect one side of the grounding cable to the grounding terminal of
the switch.
Step 2 Connect the other side of the grounding cable to the grounding terminal
of other
grounded devices or a grounding bar in the equipment room.
Note
Connect the grounding cable to the grounding system in the equipment room. Do
not connect it to a fire main or lightning rod.
2 Physical connection
Refer to the following network topology to connect the switch to other network devices.
Tip
All ports of this switch support the auto MDI/MDIX function, so both a
straight cable and a crossover cable can be used to connect the switch to
Ethernet devices.
LED indicators & button descriptions
3 Login
Step 1 Use an Ethernet cable to connect a computer to a RJ45 port of the switch.
Step 2 Set the IP address of the computer to an unused one belonging to the
same network segment with the switch.
For example, the default IP address of t he switch is 192.168.0.1, set the IP
address of the computer to 192.168.0.X (X ranges from 2 to 254 and is not be
occupied) and subnet mask to 2S5.255.2S5.0.
Step 3 Start a web browser (example: Chrome) on the computer, enter 192.168.0.1 in the address bar, and press Enter on the keyboard.
Step 4 On the login page of the switch, enter the login user name and password (both are admin by default), and click Login.
Tip
If tile login window does not appear, refer to Q1 in Appendix A FAQ.
Login to the web UI of the switch succeeded. You can configure the switch now.
Appendix A FAQ
1, I cannot log in to the web UI of the switch, What should I do?
Try the following solutions:
Check whether the switch is powered on properly.
Check whether the computer is connected to the switch properly.
Check whether the IP address of the computer is set to 192.168.0.X
(X ranges from 2 to 254 and is not be occupied).
Clear the cache of the web browser or try another web browser.
Disable the firewall of the computer, or try another computer.
Check whether only one device with the IP address 192.168.0.1 exists in the
local
network.
If the problem persists, reset the switch and try again.
Reset method: When the Power LED indicator is solid on and the SYS LED
indicator
is blinking, hold down the LED Mode button for about 10 seconds, and release
it
when all LED indicators light up. The switch is restored to factory settings
when the
SYS LED indicator blinks again.
2.1 forget the login user name and password when logging in to the web UI.
What should I do?
Try entering the default login user name and password (both are admln). If failed still, reset the switch, and then use the default user name and password to log in.
3, How to connect to the switch through the Console port?
Follow the procedures below:
Use the included console cable to connect a computer to the Console port of
the switch.
Run the connection software of console port on the computer. Putty is taken as
an example.
Set the Connection type to Serial, Speed to 115200, and click Open on the
lower right corner.
Double press Enter on your keyboard, and enter t he user name and password
(both are admin by default) of the switch in the appeared window as shown
below.
4. How to deal with power system malfunctions?
You can determine whether the power system malfunctions by observing the Power
LED indicator on the front panel of the switch. When the power system works
properly,
the Power LED indicator is solid on. If the Power LED indicator does not light
up, perform
the following operations:
Check whether the switch is properly connected to a power source using the
included power cord.
Check whether the input voltage matches the value required by the switch.
Appendix B Specifications
Appendix C Safety and statement
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
The mains plug is used as disconnect device, the disconnect device shall
remain readily operable.
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.
RECYCLING
This product bears the selective sorting symbol for Waste electrical and
electronic equipment (WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to be recycled or
dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and,
if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a
residential area is I likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution!
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: (1 ) The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. (2) To
avoid unnecessary radiation interference,
it is recommended to use a shielded RJ45 cable.
Technical support
Shenzhen Tenda Technology Co., Ltd.
6-8 Floor, Tower E3, NO.1001, Zhongshanyuan Road, Nanshan District, Shenzhen,
China. 518052
USA hotline: 1-800-570-5892
Toll Free: 7 x 24 hours
Canada hotline: 1-888-998-8966
Toll Free: Mon· Fri 9 am -6 pm PST
Hong Kong hotline: 00852-81931998
Global hotline: +86 755-2765 7180 (China 1ime Zone)
Website: www.tendacn.com
E-mail: support@tenda.com.cn
Copyright te 2020 Shenzhen Tenda Technology Co., Ltd. All rights reserved.
Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co.,
Ltd.
Other brand and product names mentioned herein are trademarks or registered
trademarks of their respective holders. Specifications are subject to change
without notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>