LUMASCAPE LS3060 Evoca In-ground Luminaire Instruction Manual
- June 4, 2024
- LUMASCAPE
Table of Contents
ERDEN E6 LS3060
LS3060 Evoca In-ground Luminaire
Please read and follow all safety instructions carefully. Failure to do so
will void the warranty.
WARNING – Product Warranty is void if the product is not installed as per
installation instructions and in compliance with all local and provincial
codes.
- Ensure installation complies with local electrical rules and regulations.
- All electrical work must be performed by a licensed electrician.
- Protective earth; protective ground (symbol 7).
- All luminaires may become hot. Use discretion on where the luminaire is mounted. Take care when setting the luminaire as it may become hot.
- Luminaire should only be used complete with a protective shield. If the protective shield is cracked, immediately stop using luminaire. Isolate light source, keep it dry and immediately contact Lumascape for replacement of the protective shield (symbol 10).
- If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by Lumascape or their service agent in order to avoid a hazard.
- The light source contained in this luminaire shall only be replaced by Lumascape or its service agent.
- Do not stare at the operating light source. The luminaire should be positioned so that prolonged staring into the luminaire at a distance closer than 26’ (8 m) is not expected (symbol 13)
- Basic insulation has been maintained between line voltage and the control conductors.
- To reduce the risk of strangulation the flexible wiring connected to this luminaire shall be effectively fixed to the wall if the wiring is within arm’s reach.
- Ensure mains input power is surge protected.
- Never make or break connections while the circuit is energized.
- Do not make modifications or alter the product.
- Keep luminaire clean and free of debris.
- Only clean with warm water.
- Do not use chemicals or abrasives to clean the luminaire as this may void the product warranty.
- Connections are to be kept clean and dry at all times.
- Suitable for use indoors or outdoors.
CAUTION Risk of Electric Shock
Pre-Install
| MODEL | LS3060 |
|---|---|
| PART NUMBER | LS3060 – 25D xxx x x xx xx 23 x 01 PS LS3060 – 25D xxx x x xx xx |
23 x 09 PS
INSTALLATION TYPE| INGROUND/IN-GRADE
IP RATING| IP66/67 (Passes IP68 Test)
SUPPLY VOLTAGE| 220-240 ~Vac, 50 Hz 120/277 ~Vac, 60 Hz
INSTRUCTIONS COVER| Single Color Dynamic Color (PowerSync)
DIMENSIONS (LxWxH)| 9.4″ x 7.1 ” (240 x 180 mm)
WEIGHT| 8.8 lbs (4.0 kg)
SURFACE TEMPERATURE| < 149 ºF (65 ºC)
STATIC LOAD RATING| 9,259 lbs (4,200 kg)
Tools Required
Herramientas necesaria
**Included Components
**
Componentes incluidos
| No Downward Force
---|---
| Do Not Use Power Tools on Screws
| Keep Electronics Free From Dirt and Moisture
| Do Not Overtighten
| Keep Away from Flammable Materials
| Do Not Hose or Pressure Clean
| Do Not Use Silicone On Outside Surface
| Do Not Cut Cable to the Luminaire
Assembly Instructions
Wiring Designations
Mains Voltage (4-Core) – International
| Designation | Color |
|---|---|
| Active | Brown |
| Neutral | Blue |
| Earth | Green / Yellow |
| Data | Black |
Do not Hi-Pot test
Mains Voltage (4-Core) – North America
| Designation | Color |
|---|---|
| Designation Active | Black |
| Neutral | White |
| Earth | Green / Yellow |
| Data | Grey or Orange |
Dimensions
IN0225-210617