VAGKRI VA-AC04 Portable Air Conditioner User Manual

VAGKRI VA-AC04 Portable Air Conditioner

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE AND SAVE FOR FUTURE REFERENCE
When using an electrical appliance, especially when children are present, basic safety precautions should always be followed, including the following:

INTENDED USE

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by person responsible for their safety.
• Close supervision is necessary when any appliance is used by or near children. Children should be supervised to ensure that they do not play with the appliance. Cleaning and user maintenance shall not be done by children unless they are older than 8 and supervised. Keep the appliance and its cord out of reach of children.
• Use the appliance only for intended household purposes as described in this User Manual. Any other use is not recommended that may cause fire, electric shock, or injury to persons.

ELECTRICITY SAFETY

• This appliance must be provided with correct voltage via a professionally installed power socket. Make sure the voltage indicated on the label of the appliance is the same as your local supply.
• Always make sure the air conditioner is properly grounded. To minimize shock and fire hazards, proper grounding is important. The power cord is equipped with a three-prong grounding plug for protection against shock hazards.
• DO NOT share a single outlet with other electrical appliances. Use on single outlet circuit only.
• DO NOT operate the air conditioner with a damaged cord or plug or if it malfunctions, is dropped or damaged in any manner. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• DO NOT start or stop the air conditioner by unplugging the power cord or turning off the power at the electrical box. DO NOT pull on the power cord.
• DO NOT use an extension cord or an adapter plug. DO NOT remove any prong from the power cord.
• In a thunderstorm, power off the air conditioner to avoid damage due to lightning.

RELATED TO USE

• DO NOT attempt to disassemble, repair, modify or replace any part of the appliance. No user-serviceable parts inside. All servicing should be performed by qualified personnel only.
• DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Read product labels for flammability and other warnings.
• DO NOT install the air conditioner in a wet room, such as a bathroom or laundry room. Too much exposure to water can cause electrical components to short circuit.
• DO NOT run the air conditioner without outside protective cover or filter in place. This could result in mechanical damage within the air conditioner.
• DO NOT sit on or place any object on top of the air conditioner.
• DO NOT insert fingers or objects in any ventilation or exhaust opening while in operation.
• Keep the cord out of heavy traffic areas and where it will not be tripped over. Never route the cord under furniture or appliances.
• Always place and use the appliance on a dry, stable, level, and horizontal surface. Make sure the appliance cannot be easily knocked over by a person or object.
• Always turn the air conditioner OFF and unplug it before cleaning, making any repairs or servicing, or whenever not in use.
• In the event of a malfunction (sparks, burning smell, etc.), immediately stop operating, disconnect the power cord and contact our Customer Support.

GFCI SAFETY PLUG

• The power supply cord has creepage protection device that senses damage to the power cord. Regularly check to make sure the safety device is working.
• Do not use this device to turn the unit on or off.
• Always make sure the RESET button is pushed in for correct operation.
• If reset fails, have the power supply replaced by qualified personnel.

1. Plug in and check if the indicator lights up green.
2. Press the TEST button, you will notice a click with the indicator off.
3. Press the RESET button, the green indicator will turn on again for use.

FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS

Specifications

EXPLORING YOUR AIR CONDITIONER

This unit may have been tilted or placed upside down during transportation. Please set it upright and outside the box for 24 hours before plugging in. Check if all accessories are included. Contact us via [email protected] if there is any missing part.

Other Accessories

Setting Up

Make sure that the exhaust hose is mounted properly and securely before use.

1. Locate upright on a firm, flat floor close to a window or opening. Leave enough circulation space around.
2. Connect the hose adapter to one end of the exhaust hose. Connect the window adapter to the other end.
3. Slide the exhaust hose assembly into the air exhaust.
4. Adjust the length of the window slider to fit your window. Secure with the included bolt.
5. Close the window to secure the window slider kit in place. Seal the gap with duct tape if required.
6. Insert the exhaust hose into the hole of the window kit. Extend to a minimum length. Avoid any sharp bends or sags.

Control Panel & Display

Control Functions

It is recommended to place the air conditioner on a firm, level surface free from obstructions with the doors and windows closed for optimum cooling efficiency.

Cool Mode

1. Tap ON/OFF button to turn on.
2. Tap MODE button until Cool indicator lights up.
3. Tap +/- button to set desired temperature (64°F~90°F / 18°C~32°C).
4. Tap FAN SPEED button to select High / Low / Auto speed.

Fan Mode

1. With unit on, tap MODE button until Fan indicator lights up.
2. Tap FAN SPEED button to select High / Low fan speed.

• In Fan mode, temperature cannot be adjusted.

Dry Mode

1. With unit on, tap MODE button until Dry indicator lights up.
2. Unscrew the drain outlet, insert the drain hose, and lead the other end to a container or drain.

• In Dry mode, temperature and fan speed cannot be adjusted.

Smart Mode

1. With unit on, tap MODE button until display screen cycles to enable Auto mode.
2. Tap FAN SPEED button to select High / Low / Auto speed.

• In Smart mode, the unit will automatically run in Cool or Fan mode based on the room temperature.

Auto ON/OFF Timer

1. With unit off or on, tap TIMER button, Timer indicator lights up.
2. Tap +/- button to set a desired time (0.5-24H) to turn on or off the unit automatically.

• To cancel timer setting, tap TIMER button again. Timer indicator turns off indicating a canceling success.

Sleep Mode
While in Cool / Dry / Smart mode, press SLEEP button on the remote control to turn on Sleep mode. The unit will maintain an optimal temperature in low speed with display of 50% brightness.

• Sleep mode is not available in Fan mode. To cancel, press SLEEP, MODE or FAN SPEED button.

Swing (Airflow Direction)
With unit on, press SWING button on the remote control. The louver will swing continuously up and down. Press this button again to stop at desired airflow direction.
*DO NOT manually adjust the air outlet louver. Adjust with remote control only.

°C/ °F Switching
With unit on, hold + and – buttons on the control panel simultaneously or press °C/°F button on the remote control to switch the unit of temperature.

Using with Remote Control

Sleep and Swing features are only available on the remote control. Other buttons are functioned in the same manner as the control panel. (Effective range: 23 ft. / 7 m.)

Installing & Replacing Batteries

• Install or replace with new batteries of the same type (AAA Alkaline) when necessary.
• When not using the remote control for extended period of time, take out the batteries.
• DO NOT attempt to dismantle the batteries.
• DO NOT dispose the batteries in fire, batteries may explode or leak.

1. Remove the battery box cover along the indicated arrow.
2. Install or replace with two new AAA alkaline batteries, making sure the + and – polarities match.
3. Install the cover back into place.

CARE AND CLEANING

• Always make sure the air conditioner is turned off and unplugged before cleaning.
• DO NOT clean with abrasive chemicals, cleaning agents or solvents.
• Never immerse in water or allow water to drip into the motor housing.

Air Inlet Grilles & Filters

1. Open the upper and lower air inlet grilles. Take out the inside air filters.
2. Clean with diluted detergent in lukewarm water (≤104°F). Rinse well and allow to air dry.
3. Return the filters to the original position and install both grilles back.

• For optimum cooling efficiency, we recommend cleaning the air filters at least once every two weeks.

Outer Surface

1. Wipe with a soft, damp cloth to remove the dirt and dust from the surface.
2. Completely dry before reconnecting to a power source.

End-of-Season Storage

1. Completely drain the water in both drain outlets.
2. Clean the air inlet grilles and filters as instructed.
3. Run in Fan mode for 15-20 minutes. Remove the exhaust hose.
4. Clean the outer surface as instructed.
5. Cover and store in a cool, dry location away from direct sunlight.

TROUBLESHOOTING GUIDE

The troubleshooting guide addresses the most common problems. If problems persist, feel free to contact the Customer Support with your order ID at [email protected]

• Q: Ft or PF code on display.

• A:

  • Ft – Water tank full when cooling. Turn off the unit, drain the water from both drain outlets and restart.
  • PF – Temperature sensor error. Contact our Customer Support for help.

• Q: The unit does not start after pressing ON/OFF button.
  A:

  • Check if the air conditioner is properly connected to a powered electrical outlet.
  • Drain the water from both drain outlets and restart.
  • Press RESET button on the safety plug. If the power trips off again, contact our Customer Support.

• Q: Not cool enough.
  A:

  • The doors or windows are not closed. Make sure all the windows and doors are closed.
  • Make sure the exhaust hose is properly connected and not blocked.
  • The air inlets are blocked. Turn off the unit and clean the inlets and filters as instructed.
  • The temperature is too high. Set to a lower temperature.
  • There are heat sources inside the room. Remove if possible.
  • For optimum cooling efficiency, avoid using in a room that is too large and try not to place the unit too close to the window with direct sunlight.

• Q: Noisy when cooling.
  A:

  • Make sure the air conditioner is placed upright on a flat, level surface with at least 20 inches of clearance on the back.
  • Make sure the exhaust hose is properly connected.
  • The air inlets are blocked. Turn off the unit and clean the inlets and filters as instructed.
  • Sound from the flowing refrigerant inside the air conditioner. This is normal. If too loud, set to a lower fan speed.

• Q: Window sliders do not fit my window.
  A: If the window sliders are too long, cut to fit your window. Or tell us the actual size of your window, we will send you a free new set of window sliders.

• Q: Water leaks.
  A:

  • Place the air conditioner on a firm, level surface.
  • Try to insert the drain hose into the continuous drain outlet to drain the water.

• Q: Power trips off.
  A: Try another outlet. Do not share the outlet with other electrical appliances.

  • Plug in again after the voltage returns stable.
  • Unplug and check if the outlet is burnt or sparks.

• Q: Air conditioner not received or no refund received after returned to Amazon.
  A: The air conditioner is delivered by Amazon. We recommend that you contact Amazon first for delivery or refund problems.

• Q: Product return or refund.
  A: Please keep the original package and provide us photos or videos regarding the quality issue. We will check and reach out to you.

WARRANTY AND SERVICE

Thank you for choosing VAGKRI Portable Air Conditioner. This product is covered with VAGKRI product and labor warranty for 12 months from the date of its original purchase.

The warranty will not apply in cases of:

• Accidents, misuse, or repairs performed by unauthorized personnel.

• Any unit that has been tampered with or used for commercial purposes.

• Normal wear and tear of wearable parts.

• Use of force, damage caused by external influences.

• Damage caused by non-observance of the User Manual, e.g. connection to an unsuitable mains supply or non-compli- ance with the instructions.

• Partially or completely dismantled appliances.

• Defects caused by or resulting from repairs, service, or alteration to the product or any of its parts that have been performed by a repair person not authorized.
  We can only provide after-sales service for products that are sold by VAGKRI or VAGKRI-authorized retailers and distributors. If you have purchased your unit from a different place, please contact your seller for return and warranty issues.

• Please have your order ID ready before contacting Customer Support.

WARNING FOR USING R32 REFRIGERANT

• When defrosting or cleaning the appliance, do not use any tools other than those recommended by the manufacturer.
• The appliance must be placed in an area without any continuously sources of ignition (open flames, gas, or electrical appliances in operation, etc).
• Do not puncture and do not burn.
• R32 is a refrigerant gas that complies with the United States directives on the environment. Do not puncture any part of the refrigerant circuit.
• If the appliance is installed, operated, or stored in an unventilated area, the room must be designed to prevent to the accumulation of refrigerant leaks resulting in a risk of fire or explosion due to ignition of the refrigerant caused by electric heaters, stoves, or other sources of ignition.
• The appliance must be stored in such a way as to prevent mechanical failure.
• Individuals who operate or work on the refrigerant circuit must have the appropriate certification issued by an accredited organization that ensures competence in handling refrigerants according to a specific evaluation recognized by associations in the industry.
• Repairs must be performed based on the recommendation from the manufacturer. Maintenance and repairs that require the assistance of other qualified personnel must be performed under the supervision of an individual specified in the use of flammable refrigerants.

Explanation of Symbols On the Unit

[email protected]

Manufacturer: Shenzhen Guiyang Network Technology Co., Ltd
Address: 1404K3, East Block, Shengtang Commercial Building, Futian District. Shenzhen. China

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>