VAGKRI VA-WF01 Wall Mount Fan User Manual

June 15, 2024
VAGKRI

VAGKRI VA-WF01 Wall Mount Fan

OREI UHDS-212 Switch 4K HDMI Splitter

READ ALL INSTRUCTIONS BEFORE USE AND SAVE FOR FUTURE REFERENC

Important Safety Instructions

  • DO NOT operate the fan without fan blades or grille guards in place.

  • DO NOT partially or fully cover or block airflow while in operation.
    Safety Precaution

  • DO NOT insert fingers or objects through the grille or fan blades while in operation.
    Safety Precaution

When using an electrical appliance, especially when children are present, basic safety precautions should always be followed, including the following:

INTENDED USE
  • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless t hey have been given supervision or instruction concerning the use of the appliance by person respond sable for their safety.
  • Close supervision is necessary when any appliance is used by or near children. Children should be supervised to ensure that they do not play with the appliance. Cleaning and user maintenance shall not be done by children unless they are older than 8 and supervised. Keep the appliance and its cord out of reach of children.
  • Use the appliance only for intended household purposes as described in this User Manual. Any other use is not recommended that may cause fi re, electric shock, or injury to persons.
ELECTRICITY SAFETY
  • This appliance must be provided with correct voltage via a professionally installed power socket. Make sure the voltage indicated on the label of the appliance is the same as your local supply.
  • DO NOT operate the fan with a damaged cord or plug or if it malfunctions, is dropped or damaged in any manner. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons.
  • WARNING – To reduce the risk of fi re or electric shock, do not use this fan with any solid- state speed control device.
  • IMPORTANT – This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to rig this safety feature.
  • This product employs overload protection (fuse). A blown fuse indicates an overload or short- circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short- circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair.
RELATED TO USE
  • DO NOT attempt to disassemble, repair, modify or replace any part of the appliance. No user serviceable parts inside. All servicing should be performed by qualified personnel only.
  • DO NOT touch or hold the mains plug with wet hands.
  • DO   NOT use this fan to ventilate areas where flammable liquids or vapors are used, stored or are present.
  • DO NOT touch any moving parts. Wait until fully stopped before touching.
  • Never use the fan without the safety guard or with a damaged safety guard.
  • Always turn the fan OFF and unplug it before cleaning, making any repairs or servicing, or whenever not in use.
  • In the event of a malfunction (sparks, burning smell, etc.), immediately stop operating, disconnect the power cord and contact our Customer Support.

FOR HOUSEHOLD USE ONLY SAVE THESE INSTRUCTIONS

Model VA-WF01
Voltage 120V~ 60Hz
Rated Power SSW

Exploring Your Wall Fan

In The Box

Check if all accessories are included. Contact us via email: support@vagkrihome.com if there is any missing part.

In The Box

Setting Up

Make sure that the wall fan is mounted properly and securely before plugging into an electrical outlet.

  1. Unscrew Grille Nut
    Unscrew the grille nut anticlockwise and set aside.
    Setting Up

  2. Install Rear Grille & Blades

  3. Situate the rear grille onto the head assembly. Tighten with the grille nut clockwise.

  4. Install the blades onto the shaft till the pin fits into the slot. Secure with the blade cap anticlockwise.
    Setting Up

  5. Install Front Grille

  6. Unlock all grille clips, attach the front grille with hook clip centered.

  7. Lock the remaining grille clips to securely attach the front grille.
    Setting Up

  8. Mount Onto Wall

  9. Secure the wall bracket onto the wall with the included screws and anchors.

  10. Hang the wall fan on the bracket.
    Setting Up

Using Your Wall Panel

Control Functions

| Fan Mode
With unit on, press to select fan mode: NORMAL/ SLEEP/ BREEZE.| ``
---|---|---
**| Auto ON/OFF Timer**
Press to set a time (1 H-2H- 4H-8H- Cancel) to turn on or turn off automatically.


| Oscillation
With unit on, press to start or stop oscillating.
Hold for 2.5s to return to default mode (NORMAL mode & HIGH speed).
**| Fan Speed
With unit on, press to adjust fan speed. **

**| Power ON/OFF**
Press to turn ON or turn OFF the fan.

Fan Modes
  • Normal Mode

    • Fan runs at selected speed.
    • 5 speeds available: LOW, MED-LOW, MED, MED-HIGH, HIGH
  • Sleep Mode

    • Fan speed reduces by 1 level every half an hour until LOW speed is reached then remains at LOW.
    • 3 speeds available: LOW. MED. HIGH
  • Breeze Mode

    • Fan speed cyclically changes for mimic natural wind.
    • 3 speeds available: LOW, MED, HIGH
Adjusting Air Flow

Do not manually adjust the oscillation angle adjust with    button on the fan or remote control

Tilt Angle (Vertical)
Hold with both hands to adjust to your desired tilt angle.
Adjusting Air Flow

Oscillation (Horizontal)
Press on the fan or remote control to oscillate horizontally.
Adjusting Air Flow

Using with Remote Control

|

  • Remove the plastic tape underneath battery before use
  • All buttons ( except button inductor ) and functioned in the same manner is the control panel

---|---

Using with Remote Control

Installing & Replacing Batteries

|

  • Replace with the new battery of the same type (CR 2025, 3V) when necessary
  • when not using the remote control for extended Period of the time, take out the battery

---|---

  1. Insert a paper clip into the button to pull out the battery compartment.
  2. Replace the battery with the same type, making sure the (+) side facing up.
  3. Push in the compartment until securely locked into place.
    Installing & Replacing Batteries

WARNING
Do Not Ingest Battery. Chemical Burn Hazard

This product contains a coin/ button cell battery. If the coin/ button cell battery is swallowed. it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. The batteries contain materials, which are hazardous to the environment; they must be removed from the appliance before it is scrapped and that they are disposed of safely.

Replacing Blown Fuse

|

  • To prevent electric shock disconnect the fan before replacing the fuse.
  • Risk of fire. Do Not replace attachment plug. Contents a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged.

---|---

  1. Grasp plug and remove from the electrical outlet.
  2. Slide fuse cover, located on the top of the plug, towards the prongs of the plug.
  3. Remove the blown fuse and snap a new fuse (2.5 Amp, 125 Volt) into place.
  4. Slide the fuse cover back to close the fuse compartment.

Use a multimeter to test if the fuse is blown.
Replacing Blown Fuse

CARE AND CLEANING

|

  • Always make sure the wall fan is turned off and unplugged before cleaning.
  • Do Not clean with abrasive chemical cleaning agents or solvents.
  • Never immerse in water or allow water to drip into the water housing.

---|---

Daily Cleaning
  1. Wipe the surface with a soft, damp cloth to remove any dirt or dust.
  2. Periodically vacuum clean the grilles to prevent dust buildup.
  3. Completely dry before reconnecting to a power source.
    Daily Cleaning
Grilles & Blades
  1. Unlock and remove the front grille, blades and rear grille.
  2. Rinse clean the grilles and blades. Allow to dry completely.
  3. Install and secure the front grille, blades and rear grille back in place.
    Grilles & Blades

Symbol When not in use for an extended period of time, take the fan off the bracket and clean as instructed. Cover and store in a cool, dry location with cord arranged.

TROUBLE SHOOTING

Symbol The troubleshooting guide address the most common problem if problem persist free to contact the customer via Email: support@vagkrihome.Com

Fan does not start.

Make sure the fan is properly connected to a powered electrical outlet and the voltage indicated is the same as your local supply.

Fan vibrates abnormally.

  • Check if the grilles and blades are properly and firmly assembled.
  • Make sure the fan is firmly mounted onto a vertical wall.

Excessive noise.

  • Check if the fan blades are properly and firmly assembled.
  • Check if the grilles and blades are clogged with dust or other buildup. We recommend that the fan be cleaned regularly.

Remote control does not work.

  • Make sure fan the is connected to a powered electrical outlet.
  • Check if the battery in remote control is enough in power.
  • Remove the obstacles between the fan and the remote. Effective distance: 5 meters.
WARRANTY AND SERVICE

Thank you for choosing VAGKRI wall fan the product is covered with VAGKRI product and Labor warranty for 12 months for the from the date of its original purchase.

The warranty will not apply in cases of:

  • Accident, misuse. or repairs performed by unauthorized personnel.
  • Any unit that has been tampered with or used for commercial purpose.
  • Normal wear and tear of wearable parts.
  • Use of force. damage caused by external influences.
  • Damage caused by non-observance of the User Manual. e.g. connection to an unsuitable mains supply or non compliance with the instructions.
  • Partially or completely dismantled appliances.
  • Defects caused by or resulting from damages from shipping or from repairs. service. or alteration to the product or any of its parts that have been performed by a repair person not authorized.

We can only provide after sales service for products that are sold by VAGKRI or VAGKRI authorized retailers and distributors. If you have purchased your unit from a different place. please contact your seller for return and warranty issues.

Customer Support

Manufacturer. Shenzhen Guiyang Network Technology Co., Ltd
Address: 1404K3, East Block, Shengtang Commercial Building, Futian District, Shenzhen, China
Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals