iNNOTECK DS-5358 2 In 1 Electric Blender and Grinder Set Instruction Manual

2 IN1
ELECTRIC BLENDER AND GRINDER SET
Instruction Manual
Save These Instructions- For Household use Only
Model:DS-5358

When using electrical appliances, basic safety precautions should always be followed. Do not use the Innoteck Kitchen Pro Blender & Grinder until you have read this manual thoroughly.

IMPORTANT SAFEGUARDS

• When using the electrical appliance, the below basic safety precautions should be followed:
• Read all instructions.
• Before using check that the voltage power corresponds to the one shown on the appliance nameplate.
• Do not let cord hang over edge of table or counter.
• Do not operate any appliance with a damage power cord or plug or after the appliance mal-function or has been damaged in any manner.
• Never leave this appliance within the reach of children.
• This appliance can be used by children aged from 8 years and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children should not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• Avoid contacting moving parts.
• Blades are sharp, so handle carefully.
• The use of attachment, including Jar, lid, not recommended or sold by manufacture may cause fire, electric shock or injury.
• The appliance cannot be used for blending hard and dry substances, otherwise the blade could be blunted.
• Switch off the appliance before approaching parts which move in use.
• Be sure to turn switch to 0 position after each use. Make sure the motor stopped completely before disassembling. And the power supply cord plug is removed from power socket.
• Do not immerse the Motor Unit into water or any other liquids.
• Do not use outdoors.
• Save these instructions for future reference

HOUSEHOLD USE ONLY

Product Overview

PRODUCT SPECIFICATIONS

Voltage/Frequency/Wattage : 220-240V 50/60Hz 500W
Glass Jar Capacity : 1.5 Litre
Grinder Capacity : 60gm

BEFORE THE FIRST USE

1. Unpack the appliance and place all parts on a horizontal surface.
2. Immerse jar, jar cover ，in warm soapy water and rinse them and dry. Never immerse motor unit in water for cleaning to prevent the risk of electric shock.
3. CAUTION: the blade is very sharp! Handle with great care.
4. Proper assembly way will be described in detail as below.
   a)Before assembling the jar, be sure the power cord is unplugged from the power socket and the Switch button is on the 0 position.
   b)The jar is suitable for making mixture which the juice and pulp are mixed.
   c)For attaching Jar, place the Jar into the motor unit directly in place, (see fig.1). Note : make sure the Jar is assembled into the motor unit properly, there is interlock switch on the position, if the Jar is not assembled properly, the blender will not operate.

BLENDING OF FRUIT AND VEGETABLE

1. Before plugging the power cord in the power socket, make sure the switch button is in the 0 position.

2. Peeled or cored the fruit or vegetables and then cut it into small dices, put the food piece into the Jar. Usually certain amount of purified water has to be added to facilitate the smooth running of appliance. The proportion of the food and water is 2:3.
   Note: Never use boiling liquids or run the appliance empty. The Jar can be used for crushing of ice.
   The amount of mixture should not exceed the max level as indicated on the Jar.

3. Turn the Jar cover into the Jar.

4. Turn the Switch button to the desired setting, there are five settings: P, 0, 1,2,3,4,5.
   Turn switch to P position and hold it to pulse actuate motor for delicate chopping.
   Release it to return the 0 position.

5. The consecutive operation time shall be less than 3 minutes . Minimum 1 minute’s rest period is required between two consecutive cycles.

6. Turn the Switch button to 0 Position once the mixture has been blended to your desired consistency.

7. Remove the Jar from the Motor Unit (remove it by directly upward), carefully take down the Jar cover, then pour and serve.

GRINDER OPERATION

1. Lay the motor unit on the flat horizontal surface and make sure it isunplugged.

2. Fill the grinding bowl with proper coffee bean, then assemble the grinding blade assembly and grinding bowl together. Please see Fig.3 NOTE: The quantity of coffee bean the grinding bowl allows to grind is Max 60g.

3. Place the grinder attachment on the motor unit, Turn the bowl clockwise until a click will be heard when locked into position properly.
   NOTE: There is a safety interlock device at the bottom of bowl, if the bowl is not assembled in place, the chopper will not operate.

4. Ensure the Speed Selector to “0” Position, then plug into power outlet.

5. Select the desired speed setting, the appliance will start grinding. During grinding, you can press down the Pulse button without releasing it if want to accelerate the process of grinding.

6. Turn the Speed Selector to “0” Position once the coffee has been ground to your desired result.

7. Disconnect from power supply once finished. Disassemble the grinder attachment from the unit, keep the grinding bowl downward and turn it anticlockwise (see fig.5), then empty the bowl and serve.

8. Do not run the appliance for more than 30s per time, and only wait until the unit is cooled to room temperature before performing next operation cycle.

CLEANING AND MAINTENANCE

1. Always disconnect the blender from the mains power supply before cleaning.
2. The Auto Clean feature can clean the blender and blade assembly easily, rapidly in complete safety.
3. Pour a little warm soapy water into the Jar and turn the Switch button to P position for a few seconds.
4. Remove the Jar from the motor unit by directly taking it upward and rinse the Jar, Jar cover under running water.
5. Wiping the outer surface of Motor Unit with a damp cloth, do not use abrasive cleansers. Never immerse in water for cleaning .
6. Dry all parts and then replace them.
7. For complete cleaning, you can hold the blade assembly at the bottom of jar carefully, for it is sharp, take it out by turning coupling on the other side clockwise emphatically then put the detachable accessories into dishwasher for clean, they are dishwasher safe attachments but the temperature setting shall not exceed 70℃.

If any problem has been encountered during use never disassemble the Motor Base by yourself, no user serviceable parts inside. Contact only the authorised service centre for examination and repair.

Cleaning the grinder

1. Detach the bowl base from the grinding blade assembly.
   NOTE: While detaching, only grasp the unsharp part of grinding blade or wear glove to prevent any injury.

2. Immerse the blade, bowl base and grinding bowl into warm soapy water for cleaning and then rinse them under running tape water.

3. Wipe the outer surface with damp cloth.
   NOTE: Never immerse the motor unit into water or any other liquid for cleaning.

4. Dry all parts thoroughly and assemble them in position.

ENVIRONMENT FRIENDLY DISPOSAL

You can help protect the environment!
Please remember to respect the local regulations: hand in the non-working electrical equipments to an appropriate waste disposal center.

Warranty

2 IN1 ELECTRIC BLENDER AND GRINDER SET
iNNOTECK
KITCHEN PRO

All data fields are required in order for us to process your request:
Model Number:
Full Name:
Address.
Phone
Email I/1400W:
Date of purchase.
We rtccfnmend TOO tee Its recipl with Miswainnty card
Retail Store of Purchase
Description of Malfunction

Return your completed warranty card to:
iN NOTECK
KITCHEN PRO
ELECTRIC BLENDER AND GRINDER SET
Model: DS-5358
1 YEAR LIMITED WARRANTY
To register warranty please go to www.innoteck.co.uk To activate your warranty, please register within 14 days of receiving your item.

Warranty

1. Most warranty repairs are handled routinely but sometimes requests for warranty service may not be appropriate. For example, warranty service would Not apply if the product damage occurred because of misuse, lack of routine, maintenance, shipping handling by third party, warehousing, or improper installation. Similarly, the warranty is void if the manufacturing date or the serial number on the product has been removed or the equipment has been altered or modified. During the warranty period the authorised service dealer at its option will repair or replace any part that upon examination is found to be defective under normal use and service.

2. The seller’s standard 12-month warranty applies to all products unless stated. You are legally covered for the first 12 months by the retailer. Within the first 12 months of ownership, you are entitled to a replacement or refund the retailers discretion. Due to this being a legal requirement we cannot get involved during this period.

3. This warranty does not cover normal wear of any parts or damage resulting from any of the following negligent use or misuse of this product, improper voltage, or current use contrary to the operation instructions: deviation from the instructions regarding storage and transportation; repair or alteration by anyone other than Innoteck or an authorised service center. Further the warranty does not cover acts of God such as fire, flood, hurricanes, or tornadoes. Innoteck shall not be liable for any incidental or consequential damages caused by the breach of any express or implied warranty. Except to the extent prohibited by applicable law any implied warranty of merchantability or fitness for a particular purpose is limited in duration to the above warranty. This warranty gives you specific legal rights and you may also have other rights as stated in the UK Consumer rights laws that may vary slightly.

4. The only time we will replace spare parts under warranty is if they have become defective within the first 12 months warranty. If you require any spare parts after the 12-month warranty has ended, you may be charged. Warranty does not apply to any accessories i.e. The guarantee is valid in the UK and Isle of Man only.

5. If your item has developed a fault the item would need to be returned to us for inspection.
   We would require the full item to be returned to us along with your proof of purchase (this can be emailed to our customer service at service @innoteckcouk) and the completed returns form (you can obtain this form from our customer service team) which must be included within the parcel. Once the item has been returned to us our returns department will check the item to confirm the fault. They will then arrange for your item to be repaired or replaced if required.
   If the product you have returned to us is end of line/discontinued or is out of stock may send you a like for replacement. We would ensure the specification of the item is like the product you have returned.

6. Within three months of purchase, if any manufacturing defects are discovered the seller will arrange to pick up the item. After three months the purchaser or customer is required to send the item to us at their own expense. There may be times when seller may request proof of purchase photo or video to assist us. A customer who is unable to send a photo or video will need to send the product to us (subject to the 3-month period).

7. Please retain your proof of purchase/sales receipt and the packaging box.

8. The product is void if the product is used for other than single-family household use or subjected to any voltage and waveform other than as specified on the product rating label. (e.g..220V-50Hz).

Customer Service: service@innoteck.co.uk

innoteck uk
Innoteck.uk
innoteck uk
Innoteck Appliances
Scan to visit our website for more products

https://innoteck.co.uk/
or visit www.innoteck.co.uk
Innoteck is a registered trademark of DST Holdings Ltd DST Holding Ltd,
Unit 20B,Calderdale Business Park, Club Lane, Halifax, West Yorkshire, HX2 8DB.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>