SUPERATV IN-SE-H-PIO1K5-001 Primal Soft Cab Enclosure Upper Doors Installation Guide

: June 15, 2024
: SUPERATV

Table of Contents

SUPERATV IN-SE-H-PIO1K5-001 Primal Soft Cab Enclosure Upper Doors
Product Information
Product Usage Instructions
Liability Statement
HOOK AND LOOP TO BODY ONLY INSTALLATION
Snaps installation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SUPERATV IN-SE-H-PIO1K5-001 Primal Soft Cab Enclosure Upper Doors

Product Information

Specifications:

Product Name: Soft Cab Doors
Compatible with: Honda Pioneer 1000

Product Usage Instructions

Installation

Read the instructions and view the illustrations before beginning.
Cut and secure the Hook and Loop to the Cage in the locations shown. Trim around any clamps on the passenger side. Repeat for the opposite side.
Place the Soft Cab onto the machine and loosely secure the straps.
Align the Soft Cab to the machine and cinch the straps tight.
Secure all flaps to the Hook and Loop fastener. Repeat for the opposite side.

Hook and Loop to Body Only Installation

If the Soft Cab is to be secured with snaps, please refer to the “Snaps Installation” section.

Cut and secure the Hook and Loop to the flaps on the lower inside portions of the door on the driver side.
Peel the backing from the Hook and Loop and fold the flap down, firmly pressing along the areas where the Hook and Loop is installed.
Wait for 15-30 minutes for the adhesive to set up.
Carefully open the flap and use one hand to gently separate the Hook and Loop fastener from the flap and plastic while opening.
Apply more heat to the Hook and Loop if needed. Repeat for the opposite side.

Snaps Installation

Outline the snap with a paint marker, lipstick, or marker.
To mark the location, press the snap onto the body or Velcro.
Install the provided snap.
Secure the door to the snap. Repeat steps for the remaining snaps.

Additional Notes:

Windows must be completely open when closing or opening the doors.
Any whiteness, clouding, wrinkles, or waves that develop on the fastener will gradually disappear when the Soft Cab is exposed to sunlight and/or heat. You can use a heat gun or hair dryer to speed up this process, but avoid overheating or heating in one area for an extended period.
Windows must be rolled up when trailering the machine.

Need Help?

If you need assistance with your installation, you can contact us:

Email: sales@superatv.com
Website: www.superatv.com
Phone: 1-855-743-3427
Support Hours:
- Monday-Thursday: 8:00am – 8:00pm EST
- Friday: 8:00am – 7:00pm EST
- Saturday: 9:00am – 2:00pm EST

Thank You For Choosing Our Product!

FAQ:

Q: What should I do if the windows develop whiteness, clouding, wrinkles, or waves?
A: Any of these issues will gradually disappear when the Soft Cab is exposed to sunlight and/or heat. You can use a heat gun or hair dryer to speed up this process, but be cautious not to overheat or heat in one area for an extended period of time.
Q: Should I roll up the windows when trailering the machine?
A: Yes, it is recommended to roll up the windows when trailering the machine to ensure their protection.

Windows must be completely open when closing or opening Doors.

Notes:

Hook and Loop Fasteners should be applied at a temperature of 70°F or above.
Use Denatured Alcohol and thoroughly clean any area where Hook and Loop Fasteners will be installed.
Installing and adjusting Soft Cab is easier with two people.
When cleaning Soft Cab, use soap and water only. Do not use detergent, window cleaner, solvents.
Do not use a dry cloth or rag on windows.
Do not fold Soft Cab before storing. Zip windows closed and roll Soft Cab to store.
Do not discard packaging until product has been successfully installed.
Doors may be secured with Snaps only, Hook and Loop Fastener only, or a combination of Snaps and Hook and Loop Fastener.
Any whiteness, clouding, wrinkles, or waves that develop will gradually disappear when Soft Cab is exposed to sunlight and/or heat. Use a heat gun or hair dryer to speed up this process. Do not overheat or heat in one area for an extended period of time.
Windows must be rolled up when trailering machine.
Cut and secure Hook and Loop to Cage in locations shown
Place Soft Cab onto machine and loosely secure Straps.
Align Soft Cab to machine.
Cinch Straps tight.
Secure all Flaps to Hook and Loop fastener.
Repeat for opposite side

Liability Statement

SuperATV’s® products are designed to best fit user’s ATV/UTV under stock conditions. Adding, modifying, or fabricating any factory or aftermarket parts will void any warranty provided by SuperATV® and is not recommended.
SuperATV’s® products could interfere with other aftermarket accessories. If user has aftermarket products on machine, contact SuperATV® to verify that they will work together.
Although SuperATV® has thousands of satisfied customers, user should be aware that installing lift kits, long travel, or suspension kits, tires, etc. will change the ride of machine and may increase maintenance and part wear. Operating any off-road machine while, or after, consuming alcohol and/or drugs increases risk of bodily harm or death. No warranty or representation is made as to this product’s ability to protect user from severe injury or death. SuperATV® urges operators and occupants to wear a helmet and appropriate riding gear at all times.
By purchasing and installing SuperATV® products, user agrees that should damages occur, SuperATV® will not be held responsible for loss of time, use, labor fees, replacement parts, or freight charges. SuperATV®, nor any 3rd party, will not be held responsible for any direct, indirect, incidental, special, or consequential damages that result from any product purchased from SuperATV®. The total liability of seller to user for all damages, losses, and causes of action, if any, shall not exceed the total purchase price paid for the product that gave rise to the claim.
SuperATV® will warranty only parts provided by SuperATV®. Any damage or problems with OEM housings, bearings, seals, or other manufacturers’ products will not be covered by SuperATV®. SuperATV® parts and products are not warrantied if item was not installed properly, misused, or modified. Installing, adding, modifying, or fabricating any factory or aftermarket product to your ATV/UTV may violate certain local, state, and federal laws. Be advised that laws vary depending on town, city, county, state, etc. Use of certain products on public streets, roads, or highways may be in violation law. The Buyer is solely and exclusively legally and personally responsible for any violation of the law by the installation or use of the product. You must abide by all local, state, and federal laws, including but not limited to vehicle safety, traffic laws, and ordinances. It is your responsibility to know the laws and how they apply to you.
The Buyer is responsible to fully understand the capability and limitations of his/her vehicle according to manufacturer specifications, warnings and instructions and agrees to hold SuperATV® harmless from any damage resulting from failure to adhere to such specifications, warnings and/ or instructions. The Buyer is also responsible to obey all applicable federal, state, and local laws and ordinances when operating his/her vehicle while using this product, and the Buyer agrees to hold SuperATV® harmless from any violation thereof.

Need help with your installation?

www.superatv.com
8:00am – 8:00pm EST M-Th
8:00am – 7:00pm EST Friday
9:00am – 2:00pm EST Saturday
sales@superatv.com
1-855-743-3427

HOOK AND LOOP TO BODY ONLY INSTALLATION

(if Soft Cab is to be secured with Snaps, see “Snaps Installation”)

Cut and secure Hook and Loop to flaps on lower inside portions of Door

THESE STEPS MUST BE DONE FOR EACH INSTANCE

Peel backing from Hook and Loop.
Fold flap down and firmly press along areas where Hook and Loop is installed
wait 15 – 30 minutes for adhesive to setup
Carefully open flap; use one hand to gently separate Hook and Loop Fastener from flap and plastic while opening.
Apply more heat to Hook and Loop