OMCAN 1050 Refrigerated Showcases
- June 15, 2024
- OMCAN
Table of Contents
- OMCAN 1050 Refrigerated Showcases
- Product Information
- Product Usage Instruction
- General Information
- Safety and Warranty
- Technical Specifications
- Operation
- Maintenance
- Troubleshooting
- Parts Breakdown
- Electrical Schematics
- Warranty Registration
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
OMCAN 1050 Refrigerated Showcases
Product Information
Specifications
- Models: RS-CN-0530, RS-CN-0700, RS-CN-1050
- Items: 43459, 41469, 43460
The Refrigerated Showcases are high-quality refrigeration units designed to keep your food items cool and fresh. With different models available, you can choose the one that suits your needs best. The showcases are manufactured by Omcan and come with a warranty for your peace of mind.
General Information
Before operating the refrigerated showcase, it is important to check the
package upon arrival and read all the provided instructions. Familiarize
yourself with the operation and safety guidelines to ensure proper usage.
Safety and Warranty
Handling and Installation:
- Handle the refrigerator with care during storage and installation.
- Before moving the refrigerator, unplug it from the wall socket and never tilt it over 45 degrees.
- Store the refrigerator in a dry place to prevent any damage.
Sufficient Space and Proper Ventilation:
- Ensure that there is at least 4/10cm of space between the wall/ceiling and the refrigerator for proper air circulation.
- Place the refrigerator in an area with good ventilation to enhance its refrigeration capabilities.
- For first-time use, set the refrigerator in its desired location and wait at least 2 hours before plugging it into the wall socket.
Away from Heat Source and No Heavy Load:
- Avoid placing the refrigerator near any heat source or in direct sunlight, as it can reduce its refrigeration capabilities.
- Do not put heavy items on top of the refrigerator to prevent damage.
No Altercations/Tampering and Stable Location:
- Do not tamper with or make changes to the refrigerator. Changes and add-ons should not be installed inside or outside of the refrigerator.
- Unpack and place the refrigerator on a flat, solid ground for stability.
Preparation and Power Supply:
- The power supply for the refrigerator should be 220V, single-phase AC with an exclusive single-phase three-pin outlet (250V/10A) and a fuse (6A).
- The power outlet must be in close proximity to the ground.
Product Usage Instruction
Operation
To operate the refrigerated showcase:
- Ensure that the refrigerator is properly installed and plugged into a suitable power outlet.
- Open the showcase door and place your food items inside, ensuring they are arranged properly for efficient cooling.
- Close the door securely to maintain the internal temperature.
- Adjust the temperature settings according to your requirements. Refer to the user manual for specific instructions on temperature control.
- The refrigerated showcase will start cooling and maintain the desired temperature automatically.
Maintenance
Regular maintenance is essential to keep your refrigerated showcase in optimal
condition. Follow these maintenance guidelines:
- Regularly clean the interior and exterior of the showcase using a mild detergent and a non-abrasive cloth.
- Remove any food spills or debris to prevent odors and contamination.
- Check and clean the condenser coils periodically to ensure efficient cooling.
- Inspect the door gaskets for any signs of wear or damage. Replace if necessary to maintain a proper seal.
- Refer to the user manual for any specific maintenance tasks recommended by the manufacturer.
Troubleshooting
If you encounter any issues with your refrigerated showcase, refer to the
troubleshooting section in the user manual. It provides step-by-step
instructions to identify and resolve common problems. If the issue persists,
contact the authorized service center for further assistance.
Parts Breakdown
For a detailed breakdown of the parts and components of the refrigerated
showcase, refer to the parts breakdown section in the user manual. It includes
labeled diagrams and part numbers for easy identification.
Electrical Schematics
If you require information about the electrical schematics of the refrigerated
showcase, refer to the electrical schematics section in the user manual. It
provides detailed diagrams and wiring information for troubleshooting
electrical issues.
Notes
The notes section in the user manual contains additional important
information, tips, and usage guidelines for your reference. Make sure to read
and understand these notes to ensure safe and efficient usage of the
refrigerated showcase.
Warranty Registration
To register your warranty or for any warranty-related queries, refer to the
warranty registration section in the user manual. Follow the provided
instructions to complete the registration process and avail of the warranty
benefits.
FAQ
-
Q: What should I do if the refrigerator is not cooling properly?
A: If the refrigerator is not cooling properly, check the following:- Ensure that the refrigerator is plugged into a working power outlet.
- Check if the temperature settings are correctly adjusted.
- Clean the condenser coils to remove any dust or debris that may be affecting cooling efficiency.
- If the issue persists, refer to the troubleshooting section in the user manual or contact the authorized service center.
-
Q: Can I install additional shelves or attachments inside the refrigerator?
A: No, it is not recommended to install additional shelves or attachments inside or outside of the refrigerator. Any alterations or tampering with the refrigerator may void the warranty and affect its performance. -
Q: How often should I clean the interior of the refrigerator?
A: It is recommended to regularly clean the interior of the refrigerator using a mild detergent and a non-abrasive cloth. Clean any spills or debris promptly to prevent odors and maintain hygiene. -
Q: What is the power supply requirement for the refrigerator?
A: The power supply for the refrigerator should be 220V, single-phase AC with an exclusive single-phase three-pin outlet (250V/10A) and a fuse (6A).
OMCAN IS NOT RESPONSIBLE FOR DIMINISHED COOLING OR ANY DAMAGE DUE TO WATER LEAKS. THE WARRANTY IS VOID IF THE AMBIENT ROOM TEMPERATURE EXCEEDS 75°F AND 55% RELATIVE HUMIDITY, AND THE APPLIANCE DRAIN IS NOT CONNECTED DIRECTLY TO A FLOOR DRAIN.
General Information
Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan, and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or negligent use of this equipment. The product shall only be operated by someone over the age of 18, of sound mind, and not under the influence of any drugs or alcohol, who has been trained in the correct operation of this machine and is wearing authorized, proper safety clothing. Any modification to the machine voids any warranty and may cause harm to individuals using the machine or in the vicinity of the machine while in operation.
CHECK PACKAGE UPON ARRIVAL
Upon receipt of an Omcan shipment please inspect for external damage. If no
damage is evident on the external packaging, open the carton to ensure all
ordered items are within the box, and there is no concealed damage to the
machine. If the package has suffered rough handling, bumps, or damage (visible
or concealed), please note it on the bill of lading before accepting the
delivery and contact Omcan within 24 hours, so we may initiate a claim with
the carrier. A detailed report on the extent of the damage caused to the
machine must be filled out within three days, from the delivery date shown in
the shipping documents. Omcan has no recourse for damaged products that were
shipped collect or third party.
Before operating any equipment, always read and familiarize yourself with all operation and safety instructions.
Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save these instructions for future reference. Also, save the original box and packaging for shipping the equipment if servicing or returning of the machine is required.
Safety and Warranty
HANDLING AND INSTALLATION
Handle with care
Unplug from the wall socket before moving. Never tilt the refrigerator over 45 degrees during handling.
| Storage
Always store the refrigerator in a dry place.
---|---
Sufficient space
To allow for proper air circulation and increased refrigeration capabilities, the refrigerator must have at least 4”/10cm of space between wall/ceiling and the machine.
| Proper ventilation
Always place the refrigerator in an area with good ventilation. For first time use, set in location and wait at least 2 hours before plugging into wall socket.
---|---
Away from heat source
Never place the refrigerator near any type of heat source or in direct sunlight, as it reduces refrigeration capabilities.
| No heavy load
Never put heavy items on top of the refrigerator.
No altercations/tampering
Never tamper with or make changes to the refrigerator. Changes and add-ons should not be installed to the inside or outside of the refrigerator.
| Stable location
Unpack and place the refrigerator on flat, solid
ground.
PREPARATION AND POWER SUPPLY
Exclusive power outlet
The power supply should be 220V, single phase AC with exclusive single phase three-pin outlet (250V/10A) and fuse (6A). The power outlet must be in close proximity to the ground.
| No shared power outlets
Refrigerator cable should never share the power outlet with any other appliance, as the cable will overheat and may result in a fire.
---|---
Protect cables
Extra caution should be used when handling cables, as broken or damaged cables can cause sparking and may result in a fire.
| No water flushing
Never flush the refrigerator surface. This can cause leakage, which may result in electrical damage or fire.
Never store flammables and explosives
No explosives or flammables should be stored in, or in proximity to, the refrigerator, such gasoline, alcohol, and adhesives.
| No spray
Never spray flammables such as paint or coating near the refrigerator. This may cause fire or malfunction.
After power outage
After a power outage or the unplugging of the refrigerator, wait at least 5 minutes before plugging it back in.
| No medicine
Medicine should not be stored inside of the refrigerator.
SUITABLE FOR HIGH-TRAFFIC AREAS WHERE NOISE LEVELS ARE NOT A CONCERN. OMCAN IS NOT RESPONSIBLE FOR DIMINISHED COOLING OR ANY DAMAGE DUE TO WATER LEAKS. WARRANTY FOR WATER LEAKS IS VOID IF THE AMBIENT ROOM TEMPERATURE EXCEEDS 75°F AND 55% RELATIVE HUMIDITY, AND THE APPLIANCE DRAIN IS NOT CONNECTED DIRECTLY TO A FLOOR DRAIN.
RESIDENTIAL USERS:
The vendor assumes no liability for parts or labor coverage for component
failure or other damages resulting from installation in non-commercial or
residential applications. The right is reserved to deny shipment for
residential usage; if this occurs, you will be notified as soon as possible.
1-YEAR PARTS AND LABOUR WARRANTY
- Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule an Omcan-authorized service technician to repair the equipment locally.
- Unauthorized maintenance will void the warranty. The warranty covers electrical and part failures not improper use.
- Please see https://omcan.com/disclaimer for complete info.
WARNING:
- The packaging components are classified as normal solid urban waste and can therefore be disposed of without difficulty.
- In any case, for suitable recycling, we suggest disposing of the products separately (differentiated waste) according to the current norms.
DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!
Technical Specifications
Model | RS-CN- 0530 | RS-CN- 0700 | RS-CN- 1050 |
---|---|---|---|
Rated Input Power | 1340 W | 2650 W | 1960 W |
Capacity | 530 L / 18.7 cu.ft. | 700 L / 24.7 cu.ft. | 1050 L / 37 cu.ft. |
Electrical | 120V / 60Hz / 1 | 220V / 60Hz / 1 | |
Lamp Power | 1.44 W / pc (LED) | ||
Shelf Load Capacity | 55 lbs. / 25 kgs. | 66 lbs. / 30 kgs. | 110 lbs. / 50 |
kgs.
Temperature Range| 2 – 10°C / 35.6 – 50°F
Max Ambient Temp Rating| 24°C / 75°F
Refrigerant and Injection| R404a (960g)| R404a (1250g)| R404a (1300g)
Type of Climate| 3
Rated Current| 11.8A| 12.7A| 9.6A
Weight| 306 lbs. / 139 kgs.| 418 lbs. / 190 kgs.| 533.5 lbs. / 242 kgs.
Packaging Weight| 352.7 lbs. / 160 kgs.| 469.6 lbs. / 213 kgs.| 621.7
lbs. / 282 kgs.
Dimensions| 36” x 30.1” x 81.5”
915 x 765 x 2070mm
| 48” x 30.1” x 81.5”
1220 x 765 x 2070mm
| 72” x 30.1” x 81.5”
1829 x 765 x 2070mm
Packaging Dimensions| 40” x 33.6” x 84”
1015 x 853 x 2130mm
| 52” x 33.6” x 84”
1320 x 853 x 2130mm
| 76” x 33.6” x 84”
1930 x 850 x 2130mm
Item Number| 43459| 41469| 43460
Operation
BEFORE USE
- Plug the refrigerator into the 220V exclusive socket.
- After the refrigerator is running, confirm that air suction/filtration is in working order and that it is sufficiently cold. After checking to make sure the refrigerator is working properly, it may be used.
DIGITAL TEMPERATURE CONTROLLER
FEATURES OF FUNCTION
- Small, integrated digital controller, which is applicable to the compressor of 1 Hp. Located behind the front grill.
- The main functions are Temperature Display/Temperature Control/manual automatic/Light Control/Value Storing/Self-Testing/Parameter Locking.
-
Set temperature: Press the button; the set temperature will be displayed. Press or button to modify and store the displayed value. Press the button to exit the adjustment and display the cold room temperature.
-
If no button is pressed within 10 seconds, the cold-room temperature will be displayed.
-
Lighting: Press the button to activate the light in the refrigerator; press it again to turn it off. Manual start/stop defrost:
Press the button and hold for 6 seconds to either defrost or stop defrosting. -
Refrigeration LED: During refrigeration, the LED is on. When the cold room temperature is constant, the LED is off. During a delayed start, the LED flashes.
-
Defrost LED: During defrosting, the LED is on. When it stops defrosting, the LED is off. During the delay of defrosting, the LED flashed.
CAUTION
- Never block the air outlet and suction to keep the air circulation and refrigeration capability constant.
- Do not overfill the refrigerator with food, as it will influence the cooling effect. If needed, adjust the rack height for proper food storage.
- Cool down hot food to room temperature before placing it inside the refrigerator.
- When the power supply has been cut off, reduce opening times and maintain a cool temperature in the refrigerator.
- To avoid scalding, never touch the compressor.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid hazards.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
Maintenance
- Cabinet Cleaning:
- The product should be maintained and cleaned periodically with the power supply disconnected. In cleaning, please use mild-rinsing water or non-corrosive products. Do not wash directly with a water faucet.
- Clean the outside of the unit using a soft cloth with neutral detergent, and dry with a separate soft cloth.
- Clean inside racks by removing them from the unit and cleaning them with water.
- When shutting down the unit for a long period of time, take out all food and unplug the wall socket. Clean inside and outside thoroughly, and keep the door open to sufficiently dry.
- As glass breaks easily, keep far away from children.
- Frequently observe the operation of the product. In case of any abnormal noise or smell, cut off the power supply immediately and call professionals. Do not restart the product before the source of trouble is found.
- We will not be responsible for any accidents acquired through failure to follow previous notices.
SERVICE
- To maintain good refrigeration performance, a refrigeration service person should be called periodically (at least twice a year) to clean the discharge honeycomb and remove any accumulated dirt from the condenser coil and condensate evaporator pan on self-contained models. POOR CIRCULATION OF AIR THROUGH THE CONDENSER COIL WILL RESULT IN POOR REFRIGERATION PERFORMANCE.
- Dirt accumulation inside the condensate evaporator pan will reduce the pan’s capacity and affect the efficiency of the heater causing a burned-out heater and an overflow of defrost water onto the store floor.
Troubleshooting
Trouble | Causes | Solutions |
---|---|---|
Strange noise under the bottom shelf. | The fan blade is broken. | Power off and |
fix the blade.
Non-refrigerating in spite of normal operation.| Unit off.| Power on.
Melting process.| Stop melting.
Refrigerant leaking.| Patch the leak and refill the refrigerant.
Unit failure.| Call Omcan.
Weak air from air curtain, and higher cabinet temperature.| Evaporator blocked
by frost.| Increase melting frequency.
The inside fan is damaged.| Replace the fan.
The too low point of temperature controller.| Adjust the set point.
Vent is blocked by storage.| Remove the storage.
Normal air curtain, but higher cabinet temperature.| Insufficient
refrigerant.| Refill the refrigerant.
Too high a set point of temperature controllers.| Adjust the set point for the
temperature controller.
The wind curtain is disturbed by strong air flow.| Removing the disturbing
factors.
Ambient temperature or humidity beyond standards.| Improve the conditions.
Melting water overflows.| Heating pipe for melting water
damaged.
| Replace the heating pipe.
---|---|---
Water level controller failure.| Replace the water level controller.
Ambient temperature or humidity beyond standards.| Improve the conditions.
Normal air curtain, but the periodical fluctuation of cabinet temperature.|
Condenser contaminated.| Clean the condenser.
Poor venting of the unit.| Improve the venting conditions.
Heat protection of compressor failure.| Replace the heat protection.
The Capillary is blocked by ice.| Replace the drying filter.
Temperature controller failure.| Replace the temperature controller.
Water leaks on the floor.| Ambient room temperature exceeds 75°F and 55%
relative humidity.| Connect the appliance drain to a floor drain.
NOTE
The following occurrences are not problems:
- The murmur of water is heard when the refrigerator is working. It is a normal occurrence as the coolant is circulating in the system.
- When the weather is damp, condensation might be found on the outside of the refrigerator. It is caused by high humidity. Simply use a cloth to wipe it off.
Parts Breakdown
Model RS-CN-0530 43459
Model RS-CN-0530 43459
Item No.| Description| Position| Item No.|
Description| Position| Item No.| Description| Position
---|---|---|---|---|---|---|---|---
67641| Compressor for 43459| 1| 60612| Lower Back Plate for 43459| 30| 67644|
Glass Deflector for 43459| 60
__
60587
| __
Water Receiver for 43459
| __
2
| __
60617
| __
Back Foam Plate for 43459
| __
31
| __
60644
| Decoration Strip of Glass Deflector for 43459| __
61
__
79304
| __
Pipe for Evaporated Water for 43459
| __
3
| __
66096
| __
Back Upper Crosspiece for 43459
| __
32
| __
60648
| Lower Front Board Components for 43459| __
62
79305| Water Level Detector for 43459| 4| 66097| Night Curtain for 43459| 33|
60649| PE for Lower Board for 43459| 63
60590| PVC Trucking for 43459| 5-1| 66098| Damper of Upper Air Outlet for
43459| 34| 60650| Lower Front Board for 43459| 64
67642| Cover of Terminal Box for 43459| 5-2| 66099| Honeycomb Panel for 43459|
35| 60651| Curtain Hook for 43459| 65
67643| Terminal Box for 43459| 5-3| 66100| Cover of Upper Air Outlet for
43459| 36| 79364| Condenser Fan Motor for 43459| 66
61167| Circuit Board Box for 43459| 6| 66101| Upper Cover Plate for 43459| 38|
67645| Fan Guard for 43459| 67
60594| Cover of Circuit Board Box for 43459| 7| 60698| Lining Foam for 43459|
39| 67646| Connection Pipe for 43459| 68
60595| LED Transformer for 43459| 9| 66102| Upper Front Board for 43459| 40|
70106| Dry Filter for 43459| 70
61246| Wire Clip Holder for 43459| 10| 60626| Lampshade Frame for 43459| 41|
60653| Heater for 43459| 71
61245| Wire Clip Cover for 43459| 11| 60627| Lampshade for 43459| 42| 60652|
Platen of Heater for 43459| 72
60599| Base for 43459| 12| 60628| Holder of Lampshade Frame for 43459| 43|
67647| Tray of Heater for 43459| 73
60600| Mesh Guard in Base for 43459| 13| 60629| Parry of Right Lining Plate
for 43459| 44| 60658| Condenser for 43459| 74
60601| Foam of Base Plate for 43459| 14| 60630| Right Support Pillar of Shelf
for 43459| 45| 71514| Switch for 43459| 75
60602| Left Board of Evaporator Cover for 43459| 15| 60631| Foam of Right
Board for 43459| 46| 60659| Window Shade Components for 43459| 76
__
60603
| __
Evaporator Cover for 43459
| __
16
| __
60632
| Back Support for Board at Air Intake for 43459| __
47
| __
60662
| __
Condenser Right Windshield for 43459
| __
77
60604| Evaporator Holder for 43459| 17| 60634| Left Support of Pillar of Shelf
for 43459| 48| 60660| Lower Front Waling for 43459| 78
60605| Evaporator Ventilation Damper for 43459| 18| 60635| Right Support
Pillar of Shelf for 43459| 49| 67648| Temperature Display for 43459| 79-1
60606| Evaporator for 43459| 19| 60636| LED Strip for 43459| 50| 67649| Main
Circuit Board for 43459| 79-2
60607| Evaporator Damper for 43459| 20| 60637| Jump Ring of LED for 43459| 51|
60666| Temperature Probe for 43459| 79-3
60608| Evaporator Wind Screen for 43459| 21| 60638| General Assembly for
Shelves for 43459| 52| 60667| Compressor Protect Probe for 43459| 79-4
60609| Plate of Air Intake for 43459| 22| 60639| Price Tag Holder for 43459|
53| 67650| Power Cord for 43459| 80
60610| Parry of Lower Air Intake for 43459| 23| 60640| Fan Blade for 43459|
54| 60672| Feet for 43459| 81
60611| Foam of Left Side Board for 43459| 24| 60641| Fan Guard for 43459| 55|
60561| Rear Wheels for 43459| 82
60613| Dead Plate of Rear Foam for 43459| 25| 60931| Motor of Evaporator for
43459| 56| 60668| Drain Pipe for 43459| 83
__
60614
| __
Left Support Pillar of Shelf for 43459
| __
26
| __
60643
| Right Board of Evaporator Cover for 43459| __
57
| __
60669
| __
Pipe Clamp for 43459
| __
84
60615| Parry of Left Lining Plate for 43459| 27| 60647| Strip of Glass
Deflector for 43459| 58| | |
60616| Ventilated Board for 43459| 29| 60645| Strip of Glass Deflector 2 for
43459| 59| | |
Model RS-CN-0700 41469
Item No.| Description| Position| Item No.|
Description| Position| Item No.| Description| Position
---|---|---|---|---|---|---|---|---
70137| Compressor for 41469| 1| 67658| Upper Back Plate for 41469| 30| 67666|
Glass Deflector for 41469| 61
__
67651
| __
Water Receiver for 41469
| __
2
| __
70100
| Upper or Lower Ventilated Board for 41469| __
31
| __
70151
| __
Strip of Glass Deflector for 41469
| __
62
__
79304
| __
Pipe for Evaporated Water for 41469
| __
3
| __
70120
| __
Panel for Rear Foam for 41469
| __
32
| __
70153
| Component for Front Base Panel for 41469| __
63
79305| Water Level Detector for 41469| 4| 70143| Rear Upper Strip for 41469|
33| 67667| PE for Lower Board for 41469| 64
60590| PVC Trucking for 41469| 5-1| 66104| Curtain for 41469| 34| 70129| Front
Panel of Base for 41469| 65
67642| Cover of Terminal Box for 41469| 5-2| 67659| Damper of Upper Air Outlet
for 41469| 35| 60651| Curtain Hook for 41469| 66
67643| Terminal Box for 41469| 5-3| 67660| Honeycomb Panel for 41469| 36|
60652| Platen of Heater for 41469| 67
61167| Circuit Board Box for 41469| 6| 70139| Upper Air Outlet for 41469| 37|
67668| Heater for 41469| 68
60594| Cover of Circuit Board Box for 41469| 7| 67661| Upper Cover Plate for
41469| 39| 70106| Dry Filter for 41469| 69
79356| LED Transformer Holder for 41469| 8| 60698| Lining Foam for 41469| 40|
60718| Tray of Heater for 41469| 70
67652| LED Transformer for 41469| 9| 70117| Front Panel on the Top for 41469|
41| 60719| Joint Pipe of Dry Filter for 41469| 71
__
60676
| __
Wire Clip Holder for 41469
| __
10
| __
70141
| __
Lampshade Frame for 41469
| __
42
| __
70112
| Reversing Condenser Fan Motor for 41469| __
72
60677| Wire Clip Cover for 41469| 11| 70142| Lampshade for 41469| 43| 67669|
Bracket of Condenser Motor for 41469| 73
70133| Cover of Base for 41469| 12| 60628| Holder of Lampshade Frame for
41469| 44| 60728| Condenser for 41469| 74
70131| Base Frame for 41469| 13| 60629| Parry of Right Lining Plate for 41469|
45| 67670| Left Panel of Condenser for 41469| 75
67653| Foam of Base Plate for 41469| 14| 60630| Right Support Pillar of Shelf
for 41469| 46| 71514| Switch for 41469| 76
60680| Left Board of Evaporator Cover for 41469| 15| 60631| Foam of Right
Board for 41469| 47| 67671| Window Shade Components for 41469| 77
__
70154
| __
Evaporator Cover for 41469
| __
16
| __
67662
| Back Support for Board at Air Intake for 41469| __
48
| __
67672
| __
Right Panel of Condenser for 41469
| __
78
60604| Evaporator Holder for 41469| 17| 67313| Bottom Shelf Bracket Left for
41469| 49| 70127| Front Bottom Strip for 41469| 79
67654| Evaporator Ventilation Damper for 41469| 18| 67314| Bottom Shelf
Bracket Right for 41469| 50| 67673| Temperature Display for 41469| 80-1
70125| Evaporator for 41469| 19| 67663| LED Strip for 41469| 51| 60724| Main
Circuit Board for 41469| 80-2
67655| Evaporator Damper for 41469| 20| 60637| Jump Ring of LED for 41469| 52|
60666| Temperature Probe for 41469| 80-3
67656| Evaporator Wind Screen for 41469| 21| 67664| General Assembly for
Shelves for 41469| 53| 67674| Compressor Protect Probe for 41469| 80-4
70132| Left/Right Air Intake for 41469| 22| 67665| Price Tag Holder for 41469|
54| 60726| Power Cord for 41469| 81
60610| Parry of Lower Air Intake for 41469| 23| 60640| Fan Blade for 41469|
55| 60672| Feet for 41469| 82
60611| Foam of Left Side Board for 41469| 24| 60641| Fan Guard for 41469| 56|
60561| Rear Wheels for 41469| 83
67657| Lower Back Plate for 41469| 25| 60682| Evaporator Fan Motor for 41469|
57| 60669| Pipe Clamp for 41469| 84
__
60613
| __
Dead Plate of Rear Foam for 41469
| __
26
| __
60681
| Right Board of Evaporator Cover for 41469| __
58
| __
60668
| __
Drain Pipe for 41469
| __
85
__
60614
| __
Left Support Pillar of Shelf for 41469
| __
27
| __
70149
| Decorating Strip of Glass Deflector for 41469| __
59
| | |
60615| Parry of Left Lining Plate for 41469| 28| 60645| Strip of Glass
Deflector 2 for 41469| 60| | |
Model RS-CN-1050 43460
Item No.| Description| Position| Item No.|
Description| Position| Item No.| Description| Position
---|---|---|---|---|---|---|---|---
70137| Compressor for 43460| 1| 60613| Dead Plate of Rear Foam for 43460| 31|
60709| Price Tag Holder for 43460| 65
__
60678
| __
Mesh Guard in Base for 43460
| __
2
| __
60614
| __
Left Support Pillar of Shelf for 43460
| __
32
| __
60710
| Decorating Strip of Glass Deflector for 43460| __
66
60599| Base for 43460| 3| 60615| Parry of Left Lining Plate for 43460| 33|
60645| Strip of Glass Deflector 2 for 43460| 67
60590| PVC Trucking for 43460| 4-1| 60690| Back Foam Plate for 43460| 34|
67686| Glass Deflector for 43460| 68
67642| Cover of Terminal Box for 43460| 4-2| 67678| Lower Back Plate for
43460| 36| 60712| Strip of Glass Deflector for 43460| 69
__
67643
| __
Terminal Box for 43460
| __
4-3
| __
67679
| __
Upper Back Plate for 43460
| __
37
| __
60713
| Lower Front Board Components for 43460| __
70
61167| Circuit Board Box for 43460| 5| 60699| Upper Front Board for 43460| 38|
60714| PE for Lower Board for 43460| 71
60594| Cover of Circuit Board Box for 43460| 6| 60692| Night Curtain for
43460| 39| 60715| Lower Front Board for 43460| 72
79356| LED Transformer Holder for 43460| 7| 67680| Damper of Upper Air Outlet
for 43460| 40| 60651| Curtain Hook for 43460| 73
67652| LED Transformer for 43460| 8| 60694| Honeycomb Panel for 43460| 41|
67687| Joint Pipe of Compressor for 43460| 74
60676| Wire Clip Holder for 43460| 9| 60695| Cover of Upper Air Outlet for
43460| 42| 60716| Platen of Heater for 43460| 75
60677| Wire Clip Cover for 43460| 10| 67681| Upper Cover Plate for 43460| 43|
60717| Heater for 43460| 76
60679| Foam of Base Plate for 43460| 11| 60698| Lining Foam for 43460| 45|
60718| Tray of Heater for 43460| 77
60680| Left Board of Evaporator Cover for 43460| 12| 60700| Lampshade Frame
for 43460| 46| 70106| Dry Filter for 43460| 78
60603| Evaporator Cover for 43460| 13| 60701| Lampshade for 43460| 47| 60719|
Joint Pipe of Dry Filter for 43460| 79
__
60681
| Right Board of Evaporator Cover for 43460| __
14
| __
60628
| __
Holder of Lampshade Frame for 43460
| __
48
| __
70112
| Reversing Condenser Fan Motor for 43460| __
80
60684| Air Inlet Plate Support for 43460| 15| 67682| LED in Light Box for
43460| 49| 67669| Bracket of Condenser Motor for 43460| 81
60682| Evaporator Fan Motor for 43460| 16| 67683| LED Transformer for 43460|
50| 60728| Condenser for 43460| 82
__
79365
| __
Fan Guard for 43460
| __
17
| __
60696
| Upper Foam Vertical Baffle Plate for 43460| __
51
| __
60723
| __
Condenser Right Windshield for 43460
| __
83
79366| Fan Blade for 43460| 18| 67684| Vertical Plate of Back Foam for 43460|
52| 60722| Condenser Left Windshield for 43460| 84
__
60685
| __
Plate of Air Intake for 43460
| __
19
| __
60686
| After the Foam Rail Support Plate for 43460| __
53
| __
71514
| __
Switch for 43460
| __
87
60605| Evaporator Ventilation Damper for 43460| 20| 60702| Space Truss Support
for 43460| 54| 60720| Window Shade Components for 43460| 88
60604| Evaporator Holder for 43460| 21| 60689| Ventilated Board for 43460| 55|
60721| Lower Front Waling for 43460| 89
__
60606
| __
Evaporator for 43460
| __
22
| __
60703
| Back Support for Board at Air Intake for 43460| __
56
| __
67673
| __
Temperature Display for 43460
| __
90-1
60607| Evaporator Damper for 43460| 23| 60629| Parry of Right Lining Plate for
43460| 57| 67688| Main Circuit Board for 43460| 90-2
60683| Evaporator Wind Screen for 43460| 24| 60630| Right Support Pillar of
Shelf for 43460| 58| 67689| Temperature Probe for 43460| 90-3
67675| Pressing Plate of Back Foam for 43460| 25| 60631| Foam of Right Board
for 43460| 59| 67690| Compressor Protect Probe for 43460| 90-4
67676| Crosspiece of Back Foam for 43460| 26| 67313| Bottom Shelf Bracket Left
for 43460| 60| 67691| Power Cord for 43460| 91
66105| Back Upper Crosspiece for 43460| 27| 67314| Bottom Shelf Bracket Right
for 43460| 61| 60672| Feet for 43460| 92
__
67677
| Thicker Crosspiece of Back Ventilated Board for 43460| __
28
| __
60637
| __
Jump Ring of LED for 43460
| __
62
| __
60561
| __
Rear Wheels for 43460
| __
93
60610| Parry of Lower Air Intake for 43460| 29| 67685| LED for 43460| 63|
60669| Pipe Clamp for 43460| 94
60611| Foam of Left Side Board for 43460| 30| 60708| General Assembly for
Shelves for 43460| 64| 60668| Drain Pipe for 43460| 95
Electrical Schematics
Model RS-CN-0530 43459
Model RS-CN-0700 41469
Model RS-CN-1050 43460
Warranty Registration
Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at the perforation and then send to the address specified below. You can also register online by visiting: https://omcan.com/warranty-registration/.
For mailing in Canada
OMCAN
PRODUCT WARRANTY REGISTRATION 3115 Pepper Mill Court, Mississauga, Ontario
Canada, L5L 4X5
For mailing in the US
OMCAN
PRODUCT WARRANTY REGISTRATION 4450 Witmer Industrial Estates, Unit 4, Niagara
Falls, New York USA, 14305
- or email to: service@omcan.com.
Purchaser’s Information
Thank you for choosing Omcan | Merci d’avoir choisi Omcan | Gracias por elegir Omcan
OMCAN
Since 1951 Omcan has grown to become a leading distributor of equipment and
supplies to the North American food service industry. Our success over these
many years can be attributed to our commitment to strengthen and develop new
and existing relationships with our valued customers and manufacturers. Today
with partners in North America, Europe, Asia, and South America, we
continually work to improve and grow the company. We strive to offer customers
exceptional value through our qualified local sales and service
representatives who provide convenient access to over 6,500 globally sourced
products.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>