QSFPTEK QT-SFP-10G-T Copper Transceiver Instruction Manual
- June 15, 2024
- QSFPTEK
Table of Contents
10GBASE-T SFP+ Copper RJ-45 30m Transceiver
P/N: QT- SFP-10G-T
FEATURES
- Supports Links up to 30m using Cat 6a/7 Cable
- SFF-8431 and SFF-8432 MSA Compliant
- IEEE 802.3az Compliant
- Low Power Consumption (2.5W max @ 30m)
- Fast Retrain EMI Cancellation Algorithm
- Low EMI Emissions
- I2C 2 Wire Serial Interface for Serial Id and Phy Registers
- Auto-negotiates with other 10GBase-T-NC PHYs
- Automatic Detection and Correction of Wiring and Polarity Swaps
- Robust Die Cast Housing
- Bail Latch Style ejector mechanism
- Unshielded and Shielded cable support
DESCRIPTION
The QSFPTEK QT-SFP-10G-T copper transceiver module is a high performance integrated duplex data link for bi-directional communication over copper cable. It is specifically designed for high speed communication links that require 10Gigabit Ethernet over Cat 6a/7 cable.This is the first SFP+ transceiver that offers 10Gb/s communication over this type of media.
General Specification
Parameter| Symbol| Min| Typ| Max| Unit|
Remarks
---|---|---|---|---|---|---
Bit Error Rate| BER| | | 10-12| |
Operating Temperature| T op| -5| | 85| °C| Case temperature
Storage Temperature| T sto,| -40| | 85| °C| Ambient temperature
Operating Humidity| –| 5| | 95| %| Non condensing
Power @30m| Is| | 2.3| 2.5| W|
Input Voltage| Vcc| 3| 3.3| 3.6| V|
- Pin Assignment
PIN #| Symbol| Description
---|---|---
1| VEET| Transmitter ground (common with receiver ground)
2| TFAULT| Transmitter Fault.
3| TDIS| Transmitter Disable. Laser output disable on high or open
4| SDA| Data line for serial ID
5| SCL| Oock line for serial ID
6| MOD_ABS| Module Absent. Grounded within the module
7| RS0| No connection required
8| LOS| Loss of Signal indication. Logic 0 indicates normal operation
9| RS1| No connection required
10| VEER| Receiver ground (common with transmitter ground)
11| VEER| Receiver ground (common with transmitter ground)
12| RD—| Receiver Inverted DATA out. AC coupled
13| RD+| Receiver Non-inverted DATA out. AC coupled
14| VEER| Receiver ground (common with transmitter ground)
15| VCCR| Receiver power supply
16| VCCR| Transmitter power supply
17| VEET| Transmitter ground (common with receiver ground)
18| TD+| Transmitter Non-Inverted DATA in. AC coupled
19| TD—| Transmitter Inverted DATA in. AC coupled
20| VEET| Transmitter ground (common with receiver ground)
Note:
1. IEEE standard 802.3ae. IEEE Standard Department, 2005.
2. Enhanced 8.5 and 10 Gigabit Small Form Factor Pluggable Module “SFP+” –
SFF-8431
3. Digital Diagnostics Monitoring Interface for Optical Transceivers –
SFF-8472.
- Electrical Pad Layout
- Mechanical Specifications
NOTES:
- MAIN BODY OF HOUSING MATERIAL: ZINC DIE CAST WITH NICKEL PLATING
- GROUNDING TABS: STAMPED BRASS WITH NICKEL PLATING
- RJ45 INSULATOR MATERIAL: STANYL TE250F6-RATED 94V-0; COLOR: BLACK
- RJ45 CONTACTS PHOSPHOR BRONZE
PLATING 50µin MIN. HARD GOLD ON CONTACT AREA, TIN ON SOLDER AREA - BAIL LATCH: MIM STEEL WITH GOLD FLASH OVER NICKEL PLATING
- EJECTOR ACTUATOR: ZINC DIE CAST WITH NICKEL PLATING
- PCB-039° THICK: 30µmm. MIN GOLD PLATING OVER 50µin. MIN NICKEL ON CONTACT AREA
- SHIELDED PLUG GROUNDING TAB: BERYLLIUM COPPER WITH NICKEL PLATING
- SCREW: STAINLESS STEEL
- Ordering information
Part numbe| Operating Case temperature
---|---
QT-SFP-10G-T| Copper SFP,10.125 Gb/s, RJ-45 connector,30M, 0°C to +70°C
QT-SFP-M| Copper SFP, 1000M, RJ-45 connector,100M, 0°C to +70°C
QT-SFP-T| Copper SFP,10/100/1000M, RJ-45 connector,100M, 0°C to +70°C