BELLEZE 050-HA-50099 Insert Fireplace Heater User Manual
- June 14, 2024
- BELLEZE
Table of Contents
23″ Insert Fireplace Heater
050-HA-50099 Insert Fireplace Heater
Scan this QR Code to view our online tutorial
https://www.belleze.com/apps/product-registration
Estimated time for assembly: 20 mins
TECHNICAL SPECIFICATION
Model Number | 050-HA-50099 |
---|---|
Dimensions (W x D x H) | 24.17” x 5.10” x 17.52” |
Net Weight | 12.57 lb |
Gross Weight | 16.53 lb |
Power Rating | 1400 W |
Voltage | 120 V |
Frequency | 60 Hz |
When using electrical appliances, basic safety precaution should always be followed including the following:
READ ALL INSTRUCTION BEFORE USE
- Read all instructions before using this heater.
- Do not use this heater outdoors.
- This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate the heater where it may fall into a bathtub or other water container.
- Do not run the power cord under carpeting.Do not cover the power cord with throw rugs, runners, or the like. Arrange the power cord away from traffic areas and where it will not be tripped over.
- To disconnect the heater, turn controls to off, then remove the plug from the outlet.
- Connect to properly grounded outlet only. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or reloadable power tap (outlet/power strip).
- To prevent a possible fire, do not use the firebox on soft surfaces, like a bed, where openings may become blocked.
- There is a thermostat limiter inside the heater. When the inner temperature overheat or abnormal heating occurs, the thermostat protective device cuts off the power supply to avoid fireplace from damaged or risk of fire.
- Use the heater only as described in the manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury.
WARNING
There is no user serviceable parts inside the fireplace/heater. If the unit
appears to be malfunction, turn off the unit and unplug from the wall outlet
immediately, and then contact the customer service.
WARNING
The heater is hot when in use. To avoid burns, do not touch hot surfaces. Keep
combustible materials such as furniture, pillows, bedding, papers, clothes,
and curtains at least 3 ft (0.9 m) away from the front of the heater, and away
from the side or rear of the heater.
WARNING
Extreme caution is necessary when heater is used by or near children or people
with physical challenges and whenever the heater is left operating unattended.
WARNING
Always unplug the heater when not in use.
WARNING
Do not operate any heater with a damaged cord or plug or after the heater
malfunctions, has been dropped, or damaged in any manner. Return the heater to
an authorized service facility or examination, electrical or mechanical
adjustment, or repair.
WARNING
Do not insert or allow foreign objects to enter any ventilation or exhaust
opening of the heater as this may cause an electric shock or fire, or damage
to the heater.
WARNING
A heater has hot and arching or sparking parts inside. Do not use in areas
wheregasoline, paint, or flammable liquids are used or stored.
WARNING
While the heater is in use, the top center of the fireplace can get hot to the
touch,and may cause serious injury or burns. Always supervise small children
around the fireplace / heater. Do not place any cloth or decorations over the
heater outlet or fireplace, or otherwise obstruct the heater outlet of the
fireplace, as this may cause a fire and serious injury.
Model No.: 050-HA-50099
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
WARNING:
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Assemble the furniture on an empty carton, carpet, or rug to prevent
scratches or damage.
For safety, please keep pets and children away from the assembly area.
Ensure the product is fully assembled before use. If you are missing any
hardware or products, do not use it until you have restored the missing
parts.
This furniture requires 2 people for assembly.
Read this instruction manual prior to assembty to familiarize yourself with
the various steps.
Lay out all components and hardware separately on a flat surface and make sure
that no parts are missing or damaged before assembly. Do not destroy or
discard any packaging until you are certain that you have ail the necessary
parts for assembly.
CAUTION
There are small components used in the construction of this product.
Loose items should be kept away from pets and children to avoid a choking
hazard.
Keep all plastic bags and packaging film away from pets and children to avoid
suffocation.
PACKAGE CONTENTS
CODE | DESCRIPTION | QTY |
---|---|---|
1 | Heater | 1 |
2 | Remote Control | 1 |
A | EVA Cushion Gasket | 4 |
B | Screws | 5 |
-
Attach EVA cushion gasket to the frame of the heater. CAUTION
The heater has a glass front panel. Careful when handling glass to prevent injury or damage. -
Set the unit from the back of the fireplace mantel and center it in the opening.
Check the alignment and attach the unit to the mantel by inserting screws through the drilled holes on the mantel. NOTE: Do not attempt to install the unit from the front of tha mantel. It will not fit.
YOU’RE FINISHED!
USER INSTRUCTION
Before use
- Check that the air intake and exhaust is not covered or obstructed in anyway.
- Keep combustible objects at least 3 ft (0.9 m) away from the unit.
- Plug the unit to a grounded power socket
Grounding
- This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock.
- This unit comes standard with a 6 ft (1.8 m) long, three wired cord. Always plug the unit into a wall outlet. An extenson or relocate tab should never be used.
CAUTION/WARNING
- Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded.
- DO NOT modify the plug provided with the product nor using any bypass device if the plug does not fit the outlet. Have a proper outlet installed by a qualified electrician.
USER INSTRUCTION (CONTROL PANEL)
Control Panel
The control panel is located on the top right corner of the unit.
Power ON / OFF
Press the power button to turn on the unit. Press again to turn off the unit.
NOTE: There is a thermostat limiter inside the unit. When the inner
temperature is too hot, the unit will automatically turned off to avoid damage
to the product or risk of fire.
CAUTION / WARNING
- DO NOT unplug the unit when it is still “ON”
Flame Control
Press the flame control button to rotate and set flame effect levels. The
flame setting are as follows
Button Press | Flame Level | Display Value | Fireplace Appearance |
---|---|---|---|
1st Press | High | L3 | Highest flame, logs glow |
2nd Press | Medium | L2 | Medium flame, logs glow |
3rd Press | Low | L1 | Low flame, logs glow |
4th Press | OFF | None | OFF |
NOTE: When the heater is turn on, the flame effect level can only rotate and set between High, Medium, and Low.
Heater Control
Press the heater control to turn on and off the heater.
When the heater is turned on, press and hold the heater control button for 5
seconds to enter temperature adjustment mode. The LED indicator is red. In
adjustment mode, the display will flashes. There are 22 levels to change
Fahrenheit temperature (ON, 62°F – 82°F). After this is set, the display will
flash 5 times and exit from setting status.
To switch from degree Fahrenheit to degree Celsius, press and hold the power
button for 5 seconds when the heater is turned on. The LED indicator will turn
to green. There are 12 levels to change Celsius temperature (ON, 17°C – 27°C).
Repeat the same process to convert Celsius to Fahrenheit.
NOTE: Degree Fahrenheit will be displayed in RED and degree Celsius will
be displayed in Green.
Timer Control
Press the timer button to turn the timer on. The timer function can controls
both the flame effect and heater.
The timer can set as the table suggested below
Button Press | Timer Interval | Display |
---|---|---|
1st press | 30 Minutes | 30 |
2nd press | 1 Hour | 1h |
3rd press | 2 Hours | 2h |
4th press | 3 Hours | 3h |
5th press | 4 Hours | 4h |
6th press | 5 Hours | 5h |
7th press | 6 Hours | 6h |
8th press | OFF | None |
NOTE: Timer only controls heater if only the heater is on before timer is
set.
NOTE: Timer only controls flame effect function if only the flame effect
function is on before timer is set.
NOTE: Timer can control both heater and flame effect function if both are
on before timer is set
Remote Control
The operation of the remote control buttons work the same as the button on the
control panel.
NOTE: The remote control cannot be used to switch between degree
Fahrenheit and degree Celsius.
Install / Replace Battery
The remote control is provided with 2 AAA batteries.
- Press and slide off the back cover from the remote control.
- Insert 2 AAA betteries into the battery compartment and make sure to intall batteries in the correct polarity.
- The negative end of the battery should be install against the spring inside the battery compartment.
CAUTION / WARNING
- Dispose old / used battery at a suitable recycling point or according to local regulations.
- DO NOT ingest battery. If accidentally swallowed, seek for medical help immediately.
FURNITURE CARE AND MAINTENANCE
Thank you for your purchase. We want your item to last as long as possible.
To ensure the product gives you years of longevity, please follow the
recommendations in this care and maintenance guide.
CLEANING
- Always turn off and unplug the unit from the power outlet before cleaning.
- Always wait until the unit has cooled down before performing any maintenace or cleaning.
- Remove any accumulated dust on the unit with a vacuum cleaner or duster.
- Clean the furniture surface with a lightly dampened cloth or soft brush.
- Dry the surface immediately after cleaning.
**** DO NOT use abrasive cleaner to clean the surface.
WARNING
The manufacturer and seller are not responsible for any and all liability
relating to personal injury, property damage or losses, whether direct,
indirect, or incidental, resulting from the incorrect attachment, improper
use, inadequate maintenance, unapproved modification or neglect of this
product.
TROUBLE SHOOTING
Problem | Solution |
---|---|
The unit does not turn on | Make sure the unit is plugged into a standard 120V |
grounded power source. Press the power button on the control panel.
Flame effect is on, but there is no flame effect| Open the top and back panel
to check if the flame spindle has fallen off from the spindle motor.
The heater does not blow warm air| Make sure the set temperature is higher
than the room temperature.
The heater does not work| Turn all switches to OFF and unplug the unit for 5
minutes.
Plug the unit back to power and operate as normal.
Error Code E3 shown on the indicator| Reset the unit by unplug the unit from
power source for 5 minutes and then plug it back.
Remote control does not work| Use it closer to the unit / change battery /
remove insulating plastic sheet.
WARRANTY
BELLEZE products come with a 1-year warranty from the date of delivery.
Register your product on our website to enjoy our limited lifetime warranty!
https://www.belleze.com/assembly-instructions
AFTER-SALE SERVICE
Encounter any difficulties or missing parts?
Contact us at 1-800-682-6376 or email
us at support@belleze.com
We will send you replacement.
Hassle free!
No need to worry about repackaging and sending your item back.
We hope you enjoy your new BELLEZE furniture!
Share your photos on Instagram and tag us: @bellezefurniture.
FOLLOW US: | CONTACT INFO: | ITEM NO. 050-HA-50099 |
---|---|---|
@bellezefurniture | spport@belleze.com | |
1-800-682-6376 | The instruction booklet |
contains IMPORTANT
safety information. Please read it in full and keep it for future reference.
© All copyright of this document belongs to BELLEZE .
This document may not be printed, translated, reproduced, or distributed in
whole or in
part without written permission from BELLEZE.
www.belleze.com
v.05032022
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>