CYP PU-HBT-EX HDBaseT Repeater Instruction Manual

: July 29, 2024
: CYP

CYP PU-HBT-EX HDBaseT Repeater

INSTRUCTION MANUAL

PU-HBT-EX
HDBaseTTM Repeater

DISCLAIMERS

The information in this manual has been carefully checked and is believed to be accurate. CYP (UK) Ltd assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be contained in this document. CYP (UK) Ltd also makes no commitment to update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document and/or product at any time and without notice.

COPYRIGHT NOTICE

No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means—electronic, mechanical, magnetic, optical, chemical, manual, or otherwise—without express written permission and consent from CYP (UK) Ltd.

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment:

Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
Never spill liquid of any kind on or into this product.
Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.
Do not attach the power supply cabling to building surfaces.
Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.
Please completely disconnect the power when the unit is not in use to avoid wasting electricity.

VERSION HISTORY

REV.	DATE	SUMMARY OF CHANGE
VR0	1/4/2013	Preliminary Release
VS1	6/24/2013	Updated format/diagrams

1. INTRODUCTION

The HDBaseT™ Repeater allows HDBaseT systems to be extended and cascaded. The model supports the highest quality of uncompressed high-definition HD video up to 4K×2K (Ultra HD), up to 8 channels of uncompressed multi-channel audio, RS-232 and IR control systems, PoE and Ethernet, complete HDBaseT 5Play™ convergence with just a simple connection over a single CAT5e/6/7 cable.

2. APPLICATIONS

HDBaseT signal extension up to 200m (300m with additional Repeater unit)
Cascading HDBaseT Matrixes
Cascading HDBaseT equipment

3. PACKAGE CONTENTS

HDBaseT Repeater
24 V/1.25 A Power Adaptor
Operation Manual

4. SYSTEM REQUIREMENTS

HDBaseT Transmitter and HDBaseT Full or Lite Receiver with CAT5e/6/7 connection cables.

5. FEATURES

HDMI, DVI and HDCP compliant
Supports 3D over HDMI and 4K×2K (Ultra HD) resolution
Supports CEC bypass
Doubles up the distance of HDBaseT transmission between transmitter and receiver, with a single repeater
Uncompressed video support up to 1080p@60Hz/36-bit and 4k×2K (Ultra HD)
Audio support up to LPCM 7.1CH, Dolby TrueHD and DTS-HD Master Audio
5Play™ Convergence: Full uncompressed HD Video, Audio, Ethernet,
Power and Controls (IR and RS-232) over a single CAT5e/6/7 cable
Powered by transmitter without power supply connection (PoE)
Installation friendly

Note: The PoE function can power this repeater so it requires no external power supply connection. When the repeater has its own external power supply connection, the power from the transmitter unit can be used to power a receiver unit connected to the repeater, but that receiver has to be PoE- enabled and compatible with both the transmitter and the repeater.

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

1. MODE LED: The yellow LED will flash when the unit is powered or when an active receiver is connected.
2. CAT5e/6 OUT: Connect to the receiver unit with a single CAT5e/6/7 cable (up to 100m).
3. LINK LED: The green LED will illuminate when output is connected to an active receiver. The LED will flash if there is a problem with the connection.

6.2 Rear Panel

1. MODE LED: The yellow LED will flash when the unit is powered or when an active transmitter is connected.
2. CAT5e/6 IN: Connect to the transmitter unit with a single CAT5e/6/7 cable (up to 100m).
3. LINK LED: The green LED will illuminate when output is connected to an active transmitter. The LED will flash if there is a problem with the connection.

4. POWER: The LED will illuminate blue when the unit is powered by a power supply or a PoE transmitter.
5. DC 24V: Connect the 24V DC power adaptor included in the package to the unit and plug it into an AC outlet.

Note: This device can be powered without the power adaptor when a PoE (Power over Ethernet) enabled active transmitter connected to the ‘CAT5e/6 IN’ port.However, in a cascading scenario when multiple repeaters are in connection, only one single repeater can be powered by PoE while the others require their own power supply connection.

7. CONNECTION DIAGRAM

8. SPECIFICATIONS

Video Bandwidth 300 MHz/10.2 Gbps
Input Port 1×CAT5e/6/7
Output Port 1×CAT5e/6/7
Resolution Support 480i~1080p@50/60, 1080p@24, 4k×2K
CAT5e/6 In/Out Distance Up to 100/100 meters
Power Supply 24 V/1.25 A DC (US/EU Standards, CE/FCC/UL certified)
Dimensions 102 mm (W)×145 mm (D)×25 mm (H)
Weight 324 g
Chassis Material Metal
Silkscreen Colour Silver
Operating Temperature 0°C ~ 40°C/32°C~104°C
Storage Temperature -20˚C ~ 60˚C / -4˚F ~ 140˚F
Relative Humidity 20~90% RH (non-condensing)
Power Consumption 9 W (PoE) or 16.2 W (Not PoE)

9. ACRONYMS

ACRONYM	COMPLETE TERM
CAT5e	Category 5 Cable
CAT6	Category 6 Cable
CAT7	Category 7 Cable
CEC	Consumer Electronics Control
HDCP	High-bandwidth Digital Content Protection
HDMI	High Definition Multimedia Interface
PoE	Power over Ethernet

CYP (UK) Ltd., Unit 7, Shepperton Business Park, Govett Avenue, Shepperton,
Middlesex, TW17 8BA
Tel: +44 (0) 20 3137 9180 | Fax: +44 (0) 20 3137 6279
Email: sales@cypeurope.com
www.cypeurope.com
VS1