BELLEZE 050-HA-50118 48 TV Stand with 18 Electric Fireplace User Guide

June 14, 2024
BELLEZE

BELLEZE 050-HA-50118 48 TV Stand with 18 Electric Fireplace

BELLEZE-050-HA-50118-48-TV-Stand-with-18-Electric-Fireplace-
PRO

Product Information

Technical Specification

Model Number| Dimensions (W x D x H)| Net Weight| Gross Weight| Power Rating| Voltage| Frequency
---|---|---|---|---|---|---
050-HA-50118| 19.17 x 5.08 x 17.52| 9.48 lb| 13 lb| 1400 W| 120 V| 60 Hz

Product Usage Instructions

Safety Precautions

  • Read all instructions before using this heater.
  • Do not use this heater outdoors.
  • This heater is not intended for use in bathrooms, laundry areas, and similar indoor locations. Never locate the heater where it may fall into a bathtub or other water container.
  • Do not run the power cord under carpeting. Do not cover the power cord with areas and where it will not be tripped over.
  • Connect to properly grounded outlet only. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or reloadable power tap (outlet/power strip).
  • Ensure proper ventilation around the heater. Do not place the heater near curtains, furniture, or other flammable materials.
  • There is a thermostat limiter inside the heater. When the inner temperature overheat or abnormal heating occurs, the thermostat protective device cuts off power to prevent damage.
  • Use the heater only as described in the manual. Any other use not specified may cause hazards.

Important Warnings

  • There are no user serviceable parts inside the fireplace/heater. If the unit appears to be malfunctioning, turn off the unit and unplug it from the wall outlet immediately, and then contact customer service.
  • The heater gets hot when in use. To avoid burns, do not touch hot surfaces. Keep combustible materials such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 ft (0.9 m) away from the front, side, or rear of the heater.
  • Extreme caution is necessary when the heater is used by or near children or people with physical challenges and whenever the heater is left operating unattended.
  • Always unplug the heater when not in use.
  • Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped, or damaged in any manner. Return the heater to an authorized service facility for examination, electrical or mechanical adjustment, or repair.
  • Do not insert or allow foreign objects to enter any ventilation or exhaust opening of the heater as this may cause an electric shock, fire, or damage to the heater.
  • A heater has hot and arching or sparking parts inside. Do not use in areas where gasoline, paint, or flammable liquids are used or stored.
  • While the heater is in use, the top center of the fireplace can get hot to the touch and may cause serious injury or burns. Always supervise small children around the fireplace/heater. Do not place any cloth or decorations over the heater outlet or fireplace, or otherwise obstruct the heater outlet of the fireplace, as this may cause a fire and serious injury.

FAQ

  • Q: Can I use this heater outdoors?
    A: No, this heater is not designed for outdoor use.

  • Q: Can I use this heater in a bathroom?
    A: No, this heater is not intended for use in bathrooms, laundry areas, and similar indoor locations.

  • Q: Can I run the power cord under carpeting?
    A: No, you should not run the power cord under carpeting. Ensure that the power cord is placed in areas where it will not be tripped over.

  • Q: Can I plug the heater into an extension cord?
    A: No, heaters should always be plugged directly into a properly grounded wall outlet/receptacle. Do not use with an extension cord or reloadable power tap (outlet/power strip).

  • Q: How far should I keep combustible materials from the heater?
    A: Keep combustible materials such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 ft (0.9 m) away from the front, side, or rear of the heater.

BELLEZE-050-HA-50118-48-TV-Stand-with-18-Electric-Fireplace-
\(1\)

TECHNICAL SPECIFICATION

Model Number 050-HA-50118
Dimensions (W x D x H) 19.17” x 5.08” x 17.52”
Net Weight 9.48 lb
Gross Weight 13 lb
Power Rating 1400 W
Voltage 120 V
Frequency 60 Hz

Safety Precaution

When using electrical appliances, basic safety precaution should always be followed including the following:

READ ALL INSTRUCTION BEFORE USE

  1. Read all instructions before using this heater.
  2. Do not use this heater outdoors.
  3. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate the heater where it may fall into a bathtub or other water container.
  4. Do not run the power cord under carpeting. Do not cover the power cord with throw rugs, runners, or the like. Arrange the power cord away from traffic areas and where it will not be tripped over.
  5. To disconnect the heater, turn controls to off, then remove the plug from the outlet.
  6. Connect to properly grounded outlet only. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or reloadable power tap (outlet/power strip).
  7. To prevent a possible fire, do not use the firebox on soft surfaces, like a bed, where openings may become blocked.
  8. There is a thermostat limiter inside the heater. When the inner temperature overheat or abnormal heating occurs, the thermostat protective device cuts off the power supply to avoid fireplace from damaged or risk of fire.
  9. Use the heater only as described in the manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury.
  • WARNING There is no user serviceable parts inside the fireplace / heater. If the unit appears to be malfunction, turn off the unit and unplug from the wall outlet immediately, and then contact the customer service.
  • WARNING The heater is hot when in use. To avoid burns, do not touch hot surfaces. Keep combustible materials such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 ft (0.9 m) away from the front of the heater, and away from the side or rear of the heater.
  • WARNING Extreme caution is necessary when heater is used by or near children or people with physical challenges and whenever the heater is left operating unattended.
  • WARNING Always unplug the heater when not in use.
  • WARNING Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped, or damaged in any manner. Return the heater to an authorized service facility or examination, electrical or mechanical adjustment, or repair.
  • WARNING Do not insert or allow foreign objects to enter any ventilation or exhaust opening of the heater as this may cause an electric shock or fire, or damage to the heater.
  • WARNING A heater has hot and arching or sparking parts inside. Do not use in areas where gasoline, paint, or flammable liquids are used or stored.
  • WARNING While the heater is in use, the top center of the fireplace can get hot to the touch, and may cause serious injury or burns. Always supervise small children around the fireplace / heater. Do not place any cloth or decorations over the heater outlet or fireplace, or otherwise obstruct the heater outlet of the fireplace, as this may cause a fire and serious injury.

Assemble the furniture on an empty carton, carpet, or rug to prevent scratches or damage. For safety, please keep pets and children away from the assembly area. Ensure the product is fully assembled before use. If you are missing any hardware or products, do not use it until you have restored the missing parts.BELLEZE-050-HA-50118-48-TV-Stand-with-18-Electric-Fireplace-
\(3\)

This furniture requires 2 people for assembly. Read this instruction manual prior to assembly to familiarize yourself with the various steps. Lay out all components and hardware separately on a flat surface and make sure that no parts are missing or damaged before assembly. Do not destroy or discard any packaging until you are certain that you have all the necessary parts for assembly.BELLEZE-050-HA-50118-48-TV-Stand-with-18-Electric-Fireplace-
\(4\)

CAUTION There are small components used in the construction of this product. Loose items should be kept away from pets and children to avoid a choking hazard. Keep all plastic bags and packaging film away from pets and children to avoid suffocation.

FCC

Model No.: 050-HA-50118

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is n guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

PACKAGE CONTENTS

BELLEZE-050-HA-50118-48-TV-Stand-with-18-Electric-Fireplace-
\(5\)

INSTALLATION

  1. Attach EVA cushion gasket to the frame of the heater.BELLEZE-050-HA-50118-48-TV-Stand-with-18-Electric-Fireplace- \(6\)
  2. Set the unit from the back of the fireplace mantel and center it in the opening. Check the alignment and attach the unit to the mantel by inserting screws through the drilled holes on the mantel.BELLEZE-050-HA-50118-48-TV-Stand-with-18-Electric-Fireplace- \(7\)

USER INSTRUCTION

  • Before use
    • Check that the air intake and exhaust is not covered or obstructed in anyway.
    • Keep combustible objects at least 3 ft (0.9 m) away from the unit.
    • Plug the unit to a grounded power socket
  • Grounding
    • This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock.
    • This unit comes standard with a 6 ft (1.8 m) long, three wired cord. Always plug the unit into a wall outlet. An extenson or relocate tab should never be used.
  • CAUTION / WARNING
    • Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded.
    • DO NOT modify the plug provided with the product nor using any bypass device if the plug does not fit the outlet. Have a proper outlet installed by a qualified electrician.

CONTROL PANEL

BELLEZE-050-HA-50118-48-TV-Stand-with-18-Electric-Fireplace-
\(9\)

Control Panel
The control panel is located on the top right corner of the unit.

Power ON / OFF
Press the power button to turn on the unit. Press again to turn off the unit.
NOTE: There is a thermostat limiter inside the unit. When the inner temperature is too hot, the unit will automatically turned off to avoid damage to the product or risk of fire.

CAUTION / WARNING
DO NOT unplug the unit when it is still “ON”.

Flame Control
Press the flame control button to rotate and set flame effect levels. The flame setting are as follows:

Button Press Flame Level Display Value Fireplace Appearance
1st Press High L3 Highest flame, logs glow
2nd Press Medium L2 Medium flame, logs glow
3rd Press Low L1 Low flame, logs glow
4th Press OFF None OFF

NOTE: When the heater is turn on, the flame effect level can only rotate and set between High, Medium, and Low.

Heater Control
Press the heater control to turn on and off the heater. When the heater is turned on, press and hold the heater control button for 5 seconds to enter temperature adjustment mode. The LED indicator is red. In adjustment mode, the display will flashes. There are 22 levels to change Fahrenheit temperature (ON, 62°F – 82°F). After this is set, the display will flash 5 times and exit from setting status. To switch from degree Fahrenheit to degree Celsius, press and hold the power button for 5 seconds when the heater is turned on. The LED indicator will turn to green. There are 12 levels to change Celsius temperature (ON, 17°C – 27°C). Repeat the same process to convert Celsius to Fahrenheit.
NOTE: Degree Fahrenheit will be displayed in RED and degree Celsius will be displayed in Green.

Timer Control
Press the timer button to turn the timer on. The timer function can controls both the flame effect and heater. The timer can set as the table sugaested below:

Button Press Timer Interval Display
1st press 30 Minutes 30
2nd press 1 Hour 1h
3rd press 2 Hours 2h
4th press 3 Hours 3h
5th press 4 Hours 4h
6th press 5 Hours 5h
7th press 6 Hours 6h
8th press OFF None

NOTE: Timer only controls heater if only the heater is on before timer is set.
NOTE: Timer only controls flame effect function if only the flame effect function is on before timer is set.
NOTE: Timer can control both heater and flame effect function if both are on before timer is set.

REMOTE CONTROL

BELLEZE-050-HA-50118-48-TV-Stand-with-18-Electric-Fireplace-
\(10\)

Remote Control
The operation of the remote control buttons work the same as the button on the control panel.
NOTE: The remote control cannot be used to switch between degree Fahrenheit and degree Celsius.

Install / Replace Battery
The remote control is provided with 2 AAA batteries.

  1. Press and slide off the back cover from the remote control.
  2. Insert 2 AAA betteries into the battery compartment and make sure to intall batteries in the correct polarity.
  3. The negative end of the battery should be install against the spring inside the battery compartment.

BELLEZE-050-HA-50118-48-TV-Stand-with-18-Electric-Fireplace-
\(11\)

CAUTION / WARNING

  • Dispose old / used battery at a suitable recycling point or according to local regulations.
  • DO NOT ingest battery. If accidentally swallowed, seek for medical help immediately

FURNITURE CARE AND MAINTENANCE

Thank you for your purchase. We want your item to last as long as possible. To ensure the product gives you years of longevity, please follow the recommendations in this care and maintenance guide.

CLEANING

  • Always turn off and unplug the unit from the power outlet before cleaning.
  • Always wait until the unit has cooled down before performing any maintenace or cleaning.
  • Remove any accumulated dust on the unit with a vacuum cleaner or duster.
  • Clean the furniture surface with a lightly dampened cloth or soft brush.
  • Dry the surface immediately after cleaning.
  • DO NOT use abrasive cleaner to clean the surface.

WARNING The manufacturer and seller are not responsible for any and all liability relating to personal injury, property damage or losses, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use, inadequate maintenance, unapproved modification or neglect of this product.

TROUBLE SHOOTING

Problem Solution
The unit does not turn on Make sure the unit is plugged into a standard 120V

grounded power source. Press the power button on the control panel.
****| Open the top and back panel to check if the motor.
The heater does not blow warm air| Make sure the set temperature is higher than the room temperature.
The heater does not work| Turn all switches to OFF and unplug the unit for 5 minutes. Plug the unit back to power and operate as normal.
Error Code E3 shown on the indicator| Reset the unit by unplug the unit from power source for 5 minutes and then plug it back.
Remote control does not work| Use it closer to the unit / change battery / remove insulating plastic sheet.

© All copyright of this document belongs to BELLEZE.
This document may not be printed, translated, reproduced, or distributed in whole or in part without written permission from BELLEZE.

WARRANTY

BELLEZE products come with a 1-year warranty from the date of delivery. Register your product on our website to enjoy our limited lifetime warranty!

AFTER-SALE SERVICE

  • Encounter any difficulties or missing parts?
  • Contact us at 1-800-682-6376 or email us at support@belleze.com
  • We will send you replacement.
  • Hassle-free!
    No need to worry about repackaging and sending your item back.

We hope you enjoy your new BELLEZE furniture!
Share your photos on Instagram and tag us: @bellezefurniture

CONTACT INFO:
upport@belleze.com
1-800-682-6376

ITEM NO. 050-HA-50118
The instruction booklet contains IMPORTANT  safety information. Please read it in full and keep it for future reference.

www.belleze.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals