KINGSUN DC-1094 Bluetooth Speaker User Manual
- June 6, 2024
- KINGSUN
Table of Contents
KINGSUN DC-1094 Bluetooth Speaker
Thank you for purchasing the Wireless Speaker. Please read this manual carefully before operating. Store this user manual in a safe place for future reference.
THE BASICS
AUX input: external audio source connected to a PC. digital media player or
any mobile phone etc.
One end of the cable should be inserted into the DC 5V jack and the other end
with the USB jack should be inserted into the USB port of the PC or to the DC
5V adaptor.
MIC input ‐ Connect the microphone which is included with the unit to the jack
AUX
Press M to select between Bluetooth/FM/Aux‐in modes.
When in Bluetooth/FM/mode. short press to move to the previous
channel/track.Pressandholdtoturndownthe volume.
BLUETOOTH CONNECTION AND OPERATION
Turn on the speaker unit and switch on the Bluetooth on your mobile or any
other device and search for the speaker name to connect.
If you have previously connected the device to the unit,the connection will
establish automatically.
Once the Bluetooth device has been connected to the unit using the above
steps. You can playback your favourite music using the ,ll key to Play/Pause.
Press the I< /‐and I/+ buttons to go to the previous or next tracks. Press and
hold the ‐and + buttons to turn the volume up and down or use the front knob.
AUX‐IN
Using the audio cable. plug one end into the audio jack of the external device
and the other end into the unit’s AUX jack. Press the M button to switch to
the Aux‐in Mode.Press and hold the ‐/+ buttons to turn the volume up and down.
When using this mode to hear music, the Previous and Next buttons will only
work from the Bluetooth device and not the unit.
FM RADIO
Press “M” to change to FM mode. Press and hold the Il button to search for FM
channels automatically. The unit will scan all FM stations and save them to
its memory.
CHARGING
Connect the charging cable to the micro‐usb port on the device and the other
end to the 5V 1Aadaptor. When the unit is charging. a RED LED light will turn
on.
ACCESSORIES
- USB charging cable :1 piece
- AUX IN cable :1 piece
- USER’S MANUAL: 1 piece
SPECIFICATIONS
- Bluetooth version:5.1+EDR
- Speaker driver unit size:4 inch*2
- Output power: 6W
- Speaker impedance: 2 Ohm
- Frequency response: 100Hz‐20 KHz
- Signal to noise ratio: >=85dB
- FM’s scan range: 81.5‐108.0 MHz
- Bluetooth wireless range: 10 meters
- Max memory USB/SD: 32GB
- USB charging: DC 5V’
- Battery capacity: 1200mAh
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.