OMCAN MG-BR-0022 Meat Grinder Instruction Manual

OMCAN MG-BR-0022 Meat Grinder

General Information

Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or negligent use of this equipment. The product shall only be operated by someone over the age of 18, of sound mind, and not under the influence of any drugs or alcohol, who has been trained in the correct operation of this machine, and is wearing authorized, proper safety clothing. Any modification to the machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of the machine while in operation.

CHECK PACKAGE UPON ARRIVAL
Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the external packaging, open carton to ensure all ordered items are within the box, and there is no concealed damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed), please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be filled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse for damaged products that were shipped collect or third party.

Before operating any equipment, always read and familiarize yourself with all operation and safety instructions.
Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save these instructions for future reference. Also save the original box and packaging for shipping the equipment if servicing or returning of the machine is required.

Safety and Warranty

GENERAL SAFETY REGULATIONS
This meat grinder is designed to grind meat products safely and efficiently. Unless the operator is properly trained and supervised, however, there is the possibility of a serious injury. It is the responsibility of the owner to ensure that this machine is used properly and safely, strictly following the instructions contained in this manual and any requirements of local law.

This machine can be potentially dangerous when used incorrectly. Therefore, read all the following instructions carefully to avoid damage:

• Before cleaning, disconnect machine from power source.
• Always turn machine off in case of power supply lack.
• Provide enough space around machine to avoid breakings.
• Never use tools not belonging to machine to help operation.
• Never feed by hand; always use stomper.
• Never put your fingers or any other object but the stomper inside the feed throat.
• Never connect power source with wet hands or wet clothes.
• Never spray water or other liquid substances directly at motor, power switch, or any other electrical components.
• Keep your working area clean and dry to prevent it from becoming slippery.
• Always install equipment in working area with adequate light and space away from children and visitors.
• Never operate without all warning labels attached and owner/operator manual available to operator.
• Never leave unattended while operating.
• Stop the machine immediately if you hear abnormal noises to prevent injuries.
• Never let dust or water get into electrical and mechanical comp machine.
• Always ground machine properly.
• Do not modify original features of the machine.
• Do not take out nor tear off any safety or identification label.
• Contact your distributor if you have any problems with the installation and operation of this machine.

RESIDENTIAL USERS: Vendor assumes no liability for parts or labor coverage for component failure or other damages resulting from installation in non-commercial or residential applications. The right is reserved to deny shipment for residential usage; if this occurs, you will be notified as soon as possible.

1 YEAR PARTS AND LABOR BENCH WARRANTY
Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule a drop off to either an Omcan authorized service depot in the area, or to an Omcan Service warehouse to repair the equipment.
Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not improper use.
Please see https://omcan.com/disclaimer for complete info.

WARNING:
The packaging components are classified as normal solid urban waste and can therefore be disposed of without difficulty.
In any case, for suitable recycling, we suggest disposing of the products separately (differentiated waste) according to the current norms.
DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!

Technical Specifications

Installation

MAIN COMPONENTS
The machine consists of an electrical motor that, through a gear box, operates a worm. The worm feeds the meat to the knife and hole plate. Several types of hole plates are available. The holes on these plates have different diameter. The type of plate is chosen depending on the desired ground meat characteristics.

The feed throat (No. 02; Figure 1) and worm (No. 03; Figure 2) receive an special treatment to isolate and facilitate the cleaning.
The knife (No. 05; Figure 2) and disc (No. 06; Figure 2) are made of hard material to provide a long life cutting quality.

INSTALLATION OF THE GRINDER

• The meat grinder must be installed on a level, non-skid surface with a maximum recommended height of 850 mm by qualified or experienced people.
• There should have a suitable space for the tray to collect processed meat in front of the grinding device.
• Check the voltage of the machine. The unit voltage must be the same as the power source.
• Grounding wire must always be connected.

1. Stomper
2. Feed Throat
3. Locking Ring
4. Tray
5. Motor Housing
6. ON/OFF Switch

Operation

PRE-OPERATION

• Check if the machine is firm; no movement shall be allowed on the supporting surface.
• It is recommended that the machine be carefully cleaned before first operation.
• Clean the grinder as explained in the maintenance section.
• After cleaning, reassemble the components in the following order: barrel, fiber washer, worm, worm pin, knife, plates, and locking ring (See Figure 2).
• Then check if all removable components are reassembled properly.
• Turn locking ring (No. 07) counterclockwise until it applies a slight pressure on the hole plate and on the knife.

NOTE : Do not tighten the locking ring too much, as an excessive pressure on the hole plate and knife may lead to their abnormal wear.

1. Barrel
2. Fiber Washer
3. Worm
4. Worm Pin
5. Knife
6. Plates: 3 mm, 5 mm or 8 mm (optional)
7. Locking Ring

NOTE : Assemble the components following the order shown above (Figure 2). It is recommended that you follow the order carefully. Assembling the components in a different order could cause serious damages to the grinding device. When re-installing the knife in the worm stud, make sure that the cutting edge is facing outwards.
After following the pre-operation instructions, your meat grinder is now ready to operate.

OPERATING THE MEAT GRINDER

1. Start the machine. This meat grinder is very high speed and, therefore, needs a fast feeding too.
2. Put the meat lumps on the tray.
3. Using the stomper (No. 01; Figure 1), push the meat into the feed throat where they will be sucked in by the worm.
4. Feed meat at a constant rate for better grinding.

IMPORTANT : Only use the stomper to push the meat into the feed throat; never use your hands or any other kind of instrument. It is strongly recommended that the meat chopper is not being operated without meat in feed. Therefore, never let the machine to work without loading. If it happens, the temperature may rise as high as 180°F in approximately 3 minutes, causing serious damages to the grinding components. Never leave any kind of knives, metal hooks, or other instruments on the tray.

Maintenance

• Turn off the machine and disconnect it from power source.
• Remove pusher (No. 01; Figure 1) and tray (No. 04; Figure 1).
• Remove Locking Ring (No. 03; Figure 1), turning it clockwise, and the internal components of the barrel, pulling them out.

NOTE: Do not try to pull the plate, knife, and worm out off the barrel as this may result in serious injury to the hands.

• To remove the barrel, loosen the locking knob located on the left side of the barrel with both hands, and move it to the left and right pulling it at the same time.
• Proceed washing the components with warm water and neutral soap.
• Wipe the body of the machine with a damp clean cloth.

Parts Breakdown

Model MG-BR-0022 11067

Item No.| Description| Position| Item No.| Description| Position| Item No.| Description| Position
---|---|---|---|---|---|---|---|---
38388| PFS Sex UNC1/4×1 RTZB for 11067| 00035.3| 38572| Complete #22 Meat Grinding Head for 11067| 09892.2| AF906| Thermal Protector Label Ingles for 11067| 33161.9
38531| PCA Sex UNC 3/8 ZB for 11067| 00108.2| 38581| Motor Gear for 11067| 13831.2| AF907| Attention Ear Wire Label Ingles/Frances for 11067| 33170.8
30258| Washer L 5/16 ZB for 11067| 00119.8| 30047| Nut M4 DIN 934 for 11067| 14175.5| 67041| Key 40127 A2E3Q-NA KEMA for 11067| 33172.4
27688| Clamp K22 (T 50R) for 11067| 00210.0| 21842| Fiber Gear for 11067| 14791.5| AF908| Attention Warning Label for 11067| 33303.4
38548| Throat Set N°22 for 11067| 00550.9| AH534| Eng. Box W/Pin (Hammed C.) for 11067| 14812.1| AH538| English/French Danger Label for 11067| 33306.9
21843| Ball Bearing 6001 for 11067| 00738.2| 30050| Terminal Cover for 11067| 17582.0| AF910| Warning Label Ingl./Franc. for 11067| 33307.7
AE670| Term. Eyelet for 11067| 01137.1| 38528| Term.Positiv Lock 2 A 4 for 11067| 17628.1| AH539| PE Extensioner for 11067| 35561.5
38545| Blades for Meat Grinders for 11067| 01657.8| 38542| Copper Tube for 11067| 19566.9| AH540| PCA M6 Special ZB for 11067| 35614.0
38518| Machine Plate 3” Dia for 11067| 01658.6| 38590| Lid Coupling Connection for 11067| 19567.7| AH541| PCA M4 Special ZB for 11067| 35615.8
38546| Disc 5mm Nº22 for 11067| 01659.4| 38541| Meat Mincer Stable for 11067| 19568.5| AH542| Certified Base (Gray) for 11067| 35632.8
16401| Retainer Seal 00784BR1(F.0122) for 11067| 01741.8| 38539| Gear Box Lid (C.Martel.) for 11067| 19647.9| AH543| 2CV 60Hz W Engine with Thermal Protector for 11067| 35706.5
21844| Worm Gear for 11067| 02720.0| 38593| Screw M5x6 DIN 84 Stainless Steel for 11067| 22996.2| AH544| Socket NO.22 Certificate for 11067| 35732.4
38534| PFS M8x25 DIN 933 ZB for 11067| 02728.6| 38412| PFS M4x5 DIN 7985 INOX for 11067| 23932.1| AH545| CB.3×5.3mm2 SJX2M Certif. for 11067| 35739.1
38393| Screw Nut M3 DIN 934 ZB for 11067| 03088.0| 38177| PFS M10x12 DIN 933 ZB for 11067| 24548.8| AH546| Wire EL.Flex.5.3x300mm Cert. for 11067| 35784.7
AH532| PFS M4x16 DIN 7985 ZB for 11067| 03139.9| AH535| Cont.CWM32-00-30D13 110V 50/60Hz for 11067| 25078.3| AH547| Wire EL.Flex.5.3x670mm Cert. for 11067| 35785.5
__

27695

| __

Allen Screw M6x8 for 11067

| __

03188.7

| __

27720

| __

Omcan Logo (Machines) for 11067

| __

27154.3

| __

AH548

| Cable Press PG21 Black6PCA W/ Red.9A14 for 11067| __

37229.3

__

38395

| __

PFS M8x10 DIN 933 ZB for 11067

| __

03196.8

| __

30059

| __

Omcan Packaging Logo for 11067

| __

27155.1

| __

AH549

| American Plug Certif.30A 125V 4A262 for 11067| __

37843.7

38530| PFS Sex UNC3/8×2.3/4 RPZB for 11067| 03214.0| AH536| Micro Drive Pin for 11067| 28237.5| AH550| Warning Label for 11067| 38110.1
27696| Nylon Cover CN 4478 for 11067| 03678.1| AF901| Shutter 25x5x100 for 11067| 29260.5| AH551| CS Tray Support for 11067| 39111.5
__

27699

| __

Cramp T 18R Small for 11067

| __

04203.0

| __

67037

| Foot Bor.Red.C/PFS M10x30 D.50x34x30 ALT for 11067| __

29340.7

| __

AH552

| __

CS Certified Cabinet for 11067

| __

39415.7

30038| Screw M3x6 DIN 84 ZB for 11067| 04208.0| AE677| Key W / Prot.30223 M2FT2FE3V / 19 for 11067| 30565.0| AH553| Certified Back Cover 1.5CV for 11067| 39419.0
21578| Knob with Bar M10x30mm for 11067| 04511.0| AH537| Micro Support for 11067| 30786.6| AH554| Completed Cabinet Certificate for 11067| 39967.1
38523| Rubber Cover for 11067| 05065.2| 67038| Grounded Wire Label for 11067| 31140.5| AH555| Spanish/English Fragile Label for 11067| 41966.4
21577| Oil Cap PSN/EE-CMSE for 11067| 08900.1| AF905| Thermal Protector Protection for 11067| 32629.1| AH556| Mouth Fixation Label for 11067| 67136.3
AH533| PFS M3x16 DIN 7985 ZB for 11067| 09093.0| 67040| Instruction Manual Label for 11067| 32832.4| AH557| CS Tray No.22 Cert. for 11067| 69620.0

Electrical Schematics

Warranty Registration

Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at the perforation and then send to the address specified below. You can also register online by visiting: https://omcan.com/warranty-registration/

or email to: service@omcan.com

Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North American food service industry. Our success over these many years can be attributed to our commitment to strengthen and develop new and existing relationships with our valued customers and manufacturers. Today with partners in North America, Europe, Asia and South America, we continually work to improve and grow the company. We strive to offer customers exceptional value through our qualified local sales and service representatives who provide convenient access to over 6,500 globally sourced products.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>