OMCAN DW-CN-0457 Pizza Display Warmer Instruction Manual

OMCAN DW-CN-0457 Pizza Display Warmer

General Information

Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or negligent use of this equipment. The product shall only be operated by someone over the age of 18, of sound mind, and not under the influence of any drugs or alcohol, who has been trained in the correct operation of this machine, and is wearing authorized, proper safety clothing. Any modification to the machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of the machine while in operation.

CHECK PACKAGE UPON ARRIVAL

Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the external packaging, open carton to ensure all ordered items are within the box, and there is no concealed damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed), please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be filled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse for damaged products that were shipped collect or third party.

Before operating any equipment, always read and familiarize yourself with all operation and safety instructions.

Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save these instructions for future reference. Also save the original box and packaging for shipping the equipment if servicing or returning of the machine is required.

Safety and Warranty

WARNING

1. If the supply cord is damaged it must be replaced by Omcan, or a qualified service agent in order to avoid any electrical hazards.
2. This appliance shall not be cleaned with any type of liquid pressurized cleaning equipment.
3. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given specific instruction with proper supervision concerning the use of this appliance.
   4. Under no circumstances should any children be allowed to operate this equipment unless properly supervised.
   5. This equipment comes with a properly grounded power cord. All power receptacles should be installed with a properly installed grounded circuit.

SAFE OPERATION NOTICE

• All operators must strictly observe and follow local state or provincial electrical safety codes and guidelines.
• This unit must be used by qualified and trained personnel at all times. Staff should be instructed on proper daily operation and maintenance prior to usage.
• Before operating machine, ensure that all covers, doors and moving components are installed properly and working prior to usage. This will ensure unit is in safe operating order and provide years of long lasting service.

RESIDENTIAL USERS: Vendor assumes no liability for parts or labor coverage for component failure or other damages resulting from installation in non-commercial or residential applications. The right is reserved to deny shipment for residential usage; if this occurs, you will be notified as soon as possible.

1 YEAR PARTS AND LABOUR BENCH WARRANTY

Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule a drop off to either an Omcan authorized service depot in the area, or to an Omcan Service warehouse to repair the equipment.

Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not improper use.
Please see https://omcan.com/disclaimer for complete info.

WARNING:

The packaging components are classified as normal solid urban waste and can therefore be disposed of without difficulty.
In any case, for suitable recycling, we suggest disposing of the products separately (differentiated waste) according to the current norms.

DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!

Technical Specifications

This pizza warmer is mainly utilized in commercial spaces such as fast-food restaurants, convenience stores along with self-service restaurants and supermarkets.

FEATURES OF OUR PRODUCTS

• The unit comes with two florescent lighting fixtures which increases the view ability of the product being displayed.
• The unit also features adjustable humidity and heat controls which allow greater flexibility to improve overall product freshness and consistency.
• The unit thermostat control allows for even heat during the warming period on all food surfaces.

TECHNICAL SPECIFICATIONS

Assembly Instructions

NSTALLING THE GLASS SIDES

1. Unscrew the glass holder brackets near the bottom of the sides of the unit until they are all loose.
2. Align one of the glass sides with the unit, putting the top of the glass into the channel located on the top of the unit.
3. Turn the bottom brackets upward and tighten, ensure that the bracket firmly holds the glass.
4. Follow steps 2 and 3 for the other sides.

INSTALLING THE DOORS

1. Lower left side door hinge assembly with two gaskets as above. Install the door hinge to the lower left side of the glass door, paying particular attention to the white colored gasket. The gasket must be placed on the  screw side of the door hinge between the glass and the door hinge itself. The other gasket is to be placed on the outside of the door hinge in between (in the same manner). Please note do not over tighten the screws as this can lead to damaging the glass door.
   

2. Remove any plastic protective film prior to assembling. Place the complete secured lower left side door and hinge assembly into the lower left side of the cabinet.
   

3. Place the left side top door hinge assembly into the upper frame left hole slot and proceed to slide and insert the complete glass door into the top door hinge. Please note the arrow direction in the figure above.
   Once in place slide supplied gaskets in between door hinge assembly and glass door making sure white gasket is in behind door hinge with screws and tighten loosely.
   

4. Paying specific attention to the door gaps, adjust accordingly leaving the same even space around the complete perimeter of the door. During this process tighten and loosen the screws till the door is plumb and level making sure it opens and closes freely without obstruction. Review the figure above.
   

5. Installing the magnet door catch/release along with the separate magnet interlock catch is similar to the door hinges; only difference is they do not swivel. They must however mate up and align facing the magnetic door latch, and separate magnet door interlock switch. It is located on the top inside right side of the display warmer case. Please note the white gaskets should always be facing the screw side of the door catches. Again align door latch and lock into place making sure it aligns to the push type locking hardware.
   Next place the interlock latch with the provided miniature magnet (black rectangular magnet)and place it into the slot of the latch and glass door. Tighten screws, paying attention not to over tighten. The door should now be able to be opened and close by simply pressing the top right hand latch and the magnet should release allowing the door to open and thus stop the rotating display. Closing is just the reverse and thus will magnetically lock the door and start the rotation of the display.
   

6. The above is a final photo of what your Pizza Display Warmer will look like. If necessary you can still adjust the door gaps as required by loosening the screws and re-adjusting the glass accordingly.
   

Installation

ACCESSORIES INCLUDED:

ELECTRICAL INSTALLATION:

When first installed ensure proper power requirements are met. A standard 15A/110-120V receptacle with ground must be utilized.

Function and Operation

• Water tray reservoir must be filled to the correct amount until low water level indicator turns off.
• Main power switch supplies power to cabinet temperature heat and humidity controls along with interior lighting. Upon closing front access door rotating product display will begin to turn for product display.
• Humidity control dial is used to increase or decrease the level of humidity in the cabinet for specific product being displayed.
• Temperature control dial is used to increase or decrease cabinet heat level. Once dialed and set the unit will monitor and control constant temperature within the cabinet.

Maintenance

• Daily maintenance should be carried out with all power to the unit in the off position, and electrical cord unplugged.
• The unit must be given appropriate time to cool down before cleaning can commence. Cleaning should be carried out by means of food grade cleaning solutions via a soft or damp cloth. Do not utilize any type of pressurized water equipment.
• Regular inspection on the outside and internal cabinet along with the power cord should be observed and carried out on a regular basis to isolate and or observe any unforeseen failure or safety concern.

Warning: cleaning outside and internal cabinet must be made with power off at all times.

Troubleshooting

COMMON TROUBLE AND SOLUTION

1. No Power.
2. Florescent lamps failure.

|

1. Inspect power source.
2. Replace florescent tubes.

Rotating Display has stopped.|

1. Motor damage.
2. Front door not completely closed.

|

1. Replace Motor.
2. Close front door/check magnetic door sensor.

Interior cabinet heat is not warming up.|

1. Thermostat off.
2. Thermostat or Heater Coil failure.

|

1. Dial in temperature.
2. Contact service agent required for possible replacement of heater coil or thermostat.

Parts Breakdown

Item No.| Description| Position| Item No.| Description| Position| Item No.| Description| Position
---|---|---|---|---|---|---|---|---
25165| Hard Surface for 20427| 1| 37510| Transformer for 20427| 15| 37516| Heater Box Assembly for 20427| 29
25166| Top Cover for 20427| 2| 37511| Terminal Block for 20427| 16| 37496| Relay for 20427| 30
25178| Draught Fan for 20427| 3| 25167| Rubber Feet for 20427| 17| 23508| Door Magnet Hardware for 20427| 31
23914| Left/Right/Back Side Glass for 20427| 4| 24746| Plug and Power Cord for 20427| 18| 37138| Fluorescent Tube Cover for 20427| 32
37509| Fluorescent Tube for 20427| 5| 25180| Motor for 20427| 19| 70406| Magnet for 20427| 33
25169| Rotary Shelf for 20427| 6| 25176| Wind-Guiding Path for 20427| 20| 70407| Door Hinges B for 20427| 34
25175| PVC Board for 20427| 7| 25179| Ambient Heater Coil for 20427| 21| 70408| Door Hinges Mat for 20427| 35
25173| Intall Box for 20427| 8| 25177| Float for 20427| 22| 70409| Door Handle for 20427| 36
25171| Indicator Light for 20427| 9| 23507| Humidity Heater Coil for 20427| 23| 70410| Rubber Gasket for 20427| 37
25172| Temperature Controller for 20427| 10| 70404| Micro Switch for 20427| 24| 70411| Bearing for 20427| 38
25170| Temperature Indicator for 20427| 11| 37514| 5 Hole Terminal Block for 20427| 25| 70412| Thermostat for 20427| 39
25174| Boat Shaped Switch for 20427| 12| 25168| Glass Door for 20427| 26| 70413| Rotating Shaft Sleeve for 20427| 40
70403| Waterproof Board for 20427| 13| 70405| Power Cord Bushings for 20427| 27| AC134| Drain Valve for 20427| 41
24766| 110V Ballast for 20427| 14| 37515| Heater Box Cover for 20427| 28| | |

Electrical Schematics

K – Power Switch
H1 – Relay
H2 – Relay
W1 – Heater
W2 – Heater
P1 – Temperature Controller
P2 – Temperature Controller
L1 – Water Shortage Indicator Light
L2 – Heating Light
L3 – Fluorescent Tube
L4 – Fluorescent Tube
H3 – Micro Switch
T1 – Temperature Display
S – Transformer
Z – Ballast
F – Level Switch

Warranty Registration

Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at the perforation and then send to the address specified below. You can also register online by visiting:

https://omcan.com/warranty-registration/

For mailing in Canada
Pour postale au Canada
For mailing in the US

OMCAN

PRODUCT WARRANTY REGISTRATION
3115 Pepper Mill Court,
Mississauga, Ontario
Canada, L5L 4X5

or email to: service@omcan.com

Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North American food service industry. Our success over these many years can be attributed to our commitment to strengthen and develop new and existing relationships with our valued customers and manufacturers. Today with partners in North America, Europe, Asia and South America, we continually work to improve and grow the company. We strive to offer customers exceptional value through our qualified local sales and service representatives who provide convenient access to over 6,500 globally sourced products.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>