OLIXIS C-3571 PU Leather Executive Swivel Computer Office Chair Instruction Manual
- June 14, 2024
- OLIXIS
Table of Contents
C-3571 PU Leather Executive Swivel Computer Office Chair
Instruction Manual
ASSEMBLY GUIDE
Congratulations, you are now the owner of the new chair!
Before enjoying the comfortable chair, you have to assemble it . This assembly
guide will take you through the basic assembly process. To make sure your
assembly progress goes smoothly, please follow the assembly instructions
specially the important safety information.
It is possible to assemble the chair by your own, while having a second person
to help you will make it easier.
Please check if there are any missing parts in the package before start. If
there are any issues, please don’t hesitate to drop us an email and we’ll help
you ASAP.
If you run into any difficulty during the assembly, remember to check out the
assembly Video to see if you’ve missed something. If you’re still unable to
resolve your problems , drop us an email and our support team will assist you.
https://qygjuser.s3.us-east-2.amazonaws.com/HL/HLC- 3571L.mp4
WARNING
To ensure proper assembly, please follow all steps and use all parts. Failure
to follow this warning can result in serious injury to yourself or others.
Package List
Without further ado, we kindly suggest you to list all parts needed for the chair first.
Assembly Instruction
Step 1:
Turn the Base (6) upside down, Align the leg (7) into with the Base and press
the Leg (7) down. Step 2:
Insert the Casters (8) into the holes at the end of each Base Leg. Step 3:
And then insert the Gas Lift (5) to the base.t
Step 4 :
Align the Mechanism (4) over the pre-drilled holes underneath the Seat
Cushion (2), make sure the front of the mechanism is facing the front of the
Seat. Attach the Mechanism to the Seat Cushion using Four Bolts (9), tighten
all the bolts with the Wrench (12).
Step 5 :
Turn the Seat Cushion (2) upright and align the center hole of the Seat Plate
over the lift, then push the Seat Cushion down onto the lift firmly until the
connection is secure. Attach the Armrest (3) to the Seat Cushion (2) with Two
Bolts (10), using the Wrench (12). The installation of the other side Armrest
is the same.
The Bolts only need to be screwed in 50%.
Note 1: The same marks on both seat and armrests are tips for installing
the armrests in the correct direction.
Note 2: Armrests are labeled with letter “L” (left) or “R” (right).
Step 6 :
Lay the Back Cushion (1) on the seat of the chair with the top of the cushion
toward the front.
Attach the Back Cushion (1) to the Arms by inserting one Bolt (10) in the
Lower holes with the Wrench (12).
The Bolts only need to be screwed in 50%.
Step 7 :
Rotate the back of the chair up, then secure it with the Bolt (10) use the
Wrench (12). Adjust the balance on each side of the chair, and fully tighten
all the bolts at this step
Step 8 :
Press Four small Caps (11) into screw holes of each side.
CAUTION:
Make sure all bolts and screws are fully tightened before using chair.
Lubricate all moving parts and tighten null bolts/screws every 6 month or
whenever needed.
Instructions For Use
- Seat Height: Paddle-shaped lever on the right side To raise: While taking your weight off chair, lift lever up.
To lower: While seated, lift lever up.
- At the proper height, your feet should rest flat on the floor.
2. Tilt Tension: Long stem under the seat with knob To increase tension:
While seated, turn knob forward (Counter clockwise).
To decrease tension:
While seated, turn knob backward (Clockwise ). - Set the tilt tension to control the resistance you feel when leaning back.
3. Operating the tilt lockout To let your chair tilt back, pull the control handle out.
To stop your chair from tilting, sit forward, then push the control handle in.
Safety And Maintenance
- Do not stand on the chair, Do Not use the chair as a stepladder.
- Use this product for seating one person at a time.
- Do not use the chair unless all bolts and screws are firmly secured.
- Avoid contact with sharp objects to prevent puncturing the fabric.
- Every 6 months, check all bolts and screws to ensure they are tight.
- To clean, spot clean only using a damp towel and mild cleaner, first test on a small, unseen area of fabric.
- Chair weight limit not to exceed 250 lbs.
Safety Information
Sit in the center of the chair, with your back to the backrest| Do not sit at
the front edge of the chair| Do not stand on the chair| Do not use the chair
with more than one person
Do not push the chair around when a person
is sitting in it| Do not push down on the backrest when a
person is reclined| Do not place all your weight on only the
backrest
Limited Warranty
The producer promises to repair or replace any chair that is found to be
defective in material or workmanship within one(1) and year from the date of
original purchase so long as you, the original purchaser, still owns it.
This is your sole and exclusive remedy. This warranty is subject to the
provisions below.
EXCLUSIONS:
This warranty does not apply and no other warranty applies to: Normal wear
and tear, which are to be expected over the course of ownership.
Misuse, abuse, or excessive use of the product.
Modifications or attachments to the product that are not approved by the
manufacturer.
Products that were not installed, used or maintained in accordance with
product instructions and warnings.
Products used for rental or commercial purposes. Damage caused by the carrier
in-transit is handled under separate terms.
SEATING USAGE:
Normal use for seating is identified as the equivalent of a single shift,
forty- (40) hour workweek. To the extent that a seating product is used in a
manner exceeding this, the applicable warranty period will be reduced in a
pro-rata manner.
Some retailers might have custom models imported directly from the factory and
therefore are not supported by our local service team because we don’t have
the correct parts, please contact your retailer directly for support. If you
have any questions about that we will be happy to assist and identify those
items.
RETURN POLICY ：
We adopt a 30 days return policy which means that all products purchased on
this website may be returned to us within the timeframe. You need to contact
us within 30 days after the product(s) came into your possession and the
product(s) must be returned to us without any undue delays. Returned products
must be returned in the same condition as they were sent and they must be sent
in its original packaging.
If the product is not faulty, (i.e. if you changed your mind or if you are
unhappy with the product for some other reason), the cost of shipping will all
on you. And it is your responsibility that the package arrives safely to us so
we recommend that you use a courier service where it is possible to track the
shipment.
If the product is faulty when you receive it please contact us and we will
help you out (see more information under Manufacturer Warranty).
We reserve the right to give a partial refund in cases when the product(s) is
not in an unused condition, is damaged or has missing parts not due to our
error.
HOW RETURNS WORK：
Contact us through the contact form on our website and attach the invoice
to the message as proof of purchase. And please also write the reason for
return.
We will then get back to you as soon as possible with information on where to
send the product(s).
As soon as we have received the product(s) and made an inspection we will
inform you of our decision.
If a refund is approved we will automatically credit the purchase to your
credit card or original method of payment.
If the product(s) is damaged, not in its original condition or missing parts
we will inform you if you are eligible for a partial refund. This is decided
from case to case depending on the severity of the damages or what parts are
missing.
HJ-Customer-Service@outlook.com
(909)637-7665 | (909)637-7593