OLIXIS ELT-P6324 Electric Standing Desk Instruction Manual

May 15, 2024
OLIXIS

OLIXIS ELT-P6324 Electric Standing Desk Instruction Manual
OLIXIS ELT-P6324 Electric Standing Desk

Dimension

1| x1 Beam| | 9| x1 Hand Controller|
---|---|---|---|---|---
2| x1 Left Leg| | 10| x1 Power Supply|
3| x1 Right Leg| | 11| x4Desk Connection Plate|
4| x1 Drive Rod| | 12| x2Cable Hole Cover|
5| 5 x2 Side Plate| | 13| x4 Wooden Pin|
6| x2 Leg Base| | 14| x2Cable Clip|
7| x1Board| | 15| x10Silicone Sheet|
7b| x1 Board| | 16| x1Phillips screwdriver|
8| x2 Desk Connection Hook| | | |
M-A x1| ScrewsME-10mm| | M-Ex10| ScrewsM4x16mm|
---|---|---|---|---|---
M-B x6| ScrewsMG-12mm| | M-F x4| ScrewsM4x6mm|
M-C x8| ScrewsMB-35mm| | M-G x1| Wrench|
M-D x14| ScrewsM4×12mm| | M-H x1| Wrench|

Please read the installation instructions carefully before installatio.
Installation
Align the holes of Left Leg (2) and Drive Rod (4), Using Wrench(M-G)to secure both withScrew (M-A).
Installation
Insert the drive rod (4) into the hole in the right leg (3): If it is not possible to insert, please rotate the right leg (3) slightly until the inner hexagon matches
Installation
As shown, use Wrench (M-H), install Beam (1) to the Legs (283) with Screws (M-B)6
Installation
Using Wrench(M-H), install Leg Base (6)
2 to the Legs (283) respectively with Screws (M-C)8.
Installation
Use screwdriver, install Side Plate (5)
2 on each side of the Legs (283) with Screws (M-F)4.
Installation
Fix Boards (7a&7b) with Wooden Pin (13)
4. Use screwdriver with Screws (M-D) 12, install Desk Connection Plate (11)4 to the middle of the Boards, and Desk Connection Hook (8)2 to both sides of the Boards
Installation
Fix Silicone Sheet (15) 10 to the corresponding hale position on the Boards (7a&7b).
Installation
Use screwdriver, secure the Leg part to the Boards (7a&7b) with Screws (M-E) 10. Please align the Silicone Sheet (15)10.
Installation
As shown, connect the motor at the Left Leg (2), Hand Controller (9) and Power Supply (10) in turn.
Installation
Using screwdriver install Hand Controller (9) to the Board (7a) with Screws (M-D)
2. Secure the connecting cable with Cable Clip (14)2 and glue it to the bottom of the Board.
Installation
Insert Cable Hole Cover (12)
2 into the hole in the Board (7b).
Step 12

Using the Controller

Controller

  • Raise the Desk
    Press the button to raise the desk continuously until it reaches the highest position or the button is released.

  • Lower the Desk
    Press the button to lower the desk continuously until it reaches the lowest position or the button is released.

  • Select Height Setting 1
    Press the button, and the desk will move to the height that was previously set for that button.

  • Select Height Setting 2
    Press the button, and the desk will move to the height that was previously set for that button.

  • Select Height Setting 3
    Press the button, and the desk will move to the height that was previously set for that button.

Save Current Height Setting
Short-press the button, and the screen will show ‘S- Press the or button to save the current height setting to that button. When you press the or button, the desk will move to the height that was previously set for that button. Any button-press will stop the desk.

Settings

  • Reset
    Press and hold the button until ‘rst is displayed. Continue holding until the desk goes down to its lowest level and comes back up slightly. Release the button, and reset is complete. If the button is released. during the reset procedure, reset will stop. The desk won’t work until reset is done correctly.

  • Child Lock
    Press and hold the and buttons together for 5 seconds to turn child lock on. The screen will show ‘LOC and the buttons will be disabled. Turn child lock o the same way.

  • Settings Menu
    Press and hold the button for 5 seconds to enter the settings menu. Short- press the button to navigate through the menu. Short-press the or button to adjust the settings. Long-press the button to quickly adjust the height settings. Press and hold the button again to save the changes. ‘SUS’ will be displayed if saving is successful (or “FAL’ if saving fails). If there is no button-press for 10 seconds, the settings menu will be exited automatically.

  • Power-Saving Mode
    The screen will turn o if there is no button-press for a minute. Any button- press will turn the screen on again.

| Protection Mode Error Codes
---|---
SCO| Standby Overvoltage Protection: Standby voltage too high. Power o the desk, check the connection between power and the controller, and power on again. If error code persists, please contact technical support.
SC1| Power Supply Overvoltage Protection: Input voltage too high If the correct AC adapter is being used, power o the desk, check the connection between power and the controller,and power on again. If error code persists, please contact technical support.
$C4| Operating Overvoltage Protection: Operating voltage too high. Power o the desk, check the connection between power and the controller, and power on again. If error code persists, please contact technical support.
hot| Overheating Protection: When the motor has been working continuously for too long, it will stop operating to prevent overheating. Wait for at least 18 minutes (until error code disappears) before making any further height adjustment.
r-6| Power Supply Overvoltage Protection (during use): Input voltage too high. Error clears when power supply voltage returns to normal. If error code persists, please contact technical support.
rst| Reset Warning: Continue to complete reset.
E10| Short Circuit Protection: Power o, check the cable connections, and power back on again. If error persists. please contact technical support.
Eli| Overloading Protection: Max load exceeded. Error code will persist for 20 seconds (DO NOT operate). Take the things o the desk and confirm there is no mechanical damage before trying again.
---|---
El2| Motor Phase Error Protection: Power o, check the cable connection between the motor and the controller, and power back on again. Then follow the reset instructions. If error code persists, please contact technical support.
El3| Sensor Malfunction Warning: Motor sensor can’t be detected. Power o, check the cable connection between the motor and the controller, and power back on again. Then follow the reset instructions. If error code persists, please contact technical support.
E14| Anti•Collision System Warning: Impact detected. The desk will move 2″ (50mm) in the opposite direction and stop.
El6| Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should return once all connectors are properly connected. If error code persists, please contact technical support.
El 7| Mechanical Failure Warning: Check if there is any structural damage or motor fault.

Technical Support

909)637-7665 | (909)637-7593
Other Info
HJ-Customer-Service@outlook.com
Thank you for choosing this product. We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don’t hesitate to contact us

HJ-Customer-Service@outlook.com
(909)637-7665 | (909)637-7593
EST 9:00AM–17:00PM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals