OLIXIS D-ELT001-4824 Electric Height Adjustable Sit Stand Ergonomic Desk Computer Workstations Instruction Manual

June 17, 2024
OLIXIS

Electric Standing Desk
Instruction Manual
D-ELT001-5524
D-ELT001-4024
D-ELT001-4824

OLIXIS D-ELT001-4824 Electric Height Adjustable Sit Stand Ergonomic Desk
Computer Workstations

Specifications

OLIXIS D-ELT001-4824 Electric Height Adjustable Sit Stand Ergonomic Desk
Computer Workstations - Specifications

Step 1 Supplied Parts and Hardware

OLIXIS D-ELT001-4824 Electric Height Adjustable Sit Stand Ergonomic Desk
Computer Workstations - Supplied Parts and Hardware

Step 2

OLIXIS D-ELT001-4824 Electric Height Adjustable Sit Stand Ergonomic Desk
Computer Workstations - Parts and Hardware

Step 3

OLIXIS D-ELT001-4824 Electric Height Adjustable Sit Stand Ergonomic Desk
Computer Workstations - Hardware

Step 4

OLIXIS D-ELT001-4824 Electric Height Adjustable Sit Stand Ergonomic Desk
Computer Workstations - Supplied Parts

Step 5

Step 6

Setting the Desk Legs to the Same Height

OLIXIS D-ELT001-4824 Electric Height Adjustable Sit Stand Ergonomic Desk
Computer Workstations - Same Height

Before attaching the transmission rod, measure the heights of the two desk legs to see if they are set at the same level. If not, insert the transmission rod into the hole in the right leg. Turn the rod to adjust the right leg so it’s level with the left leg. Turn the rod  clockwise to lower the right leg or anti-clockwise to raise it.

Step 1

OLIXIS D-ELT001-4824 Electric Height Adjustable Sit Stand Ergonomic Desk
Computer Workstations - Setting the Desk Legs

OLIXIS D-ELT001-4824 Electric Height Adjustable Sit Stand Ergonomic Desk
Computer Workstations - Setting the Desk Legs 2

Step 2

OLIXIS D-ELT001-4824 Electric Height Adjustable Sit Stand Ergonomic Desk
Computer Workstations - Desk Legs

Step 3 Attaching the Leg Bases

OLIXIS D-ELT001-4824 Electric Height Adjustable Sit Stand Ergonomic Desk
Computer Workstations - the Leg Bases

Step 4 Assembling and Attaching the Desktop

OLIXIS D-ELT001-4824 Electric Height Adjustable Sit Stand Ergonomic Desk
Computer Workstations - Attaching the Desktop

Secure the desktop panels with the connectors. Then attach the hooks and controller to the desktop.

OLIXIS D-ELT001-4824 Electric Height Adjustable Sit Stand Ergonomic Desk
Computer Workstations - screw holes

Place rubber pads on the desktop screw holes.

OLIXIS D-ELT001-4824 Electric Height Adjustable Sit Stand Ergonomic Desk
Computer Workstations - frame to the desktop

Attach the frame to the desktop.

Step 5 Connecting the Cables

OLIXIS D-ELT001-4824 Electric Height Adjustable Sit Stand Ergonomic Desk
Computer Workstations - Connecting the Cables

Step 6 Installing the Cable Hole Covers

OLIXIS D-ELT001-4824 Electric Height Adjustable Sit Stand Ergonomic Desk
Computer Workstations - Cable Hole Covers

Using the Controller

  • Raise the Desk
    Press the button to raise the desk continuously until it reaches the highest position or the button is released.

  • Lower the Desk
    Press the button to lower the desk continuously until it reaches the lowest position or the button is released.

  • Select Height Setting 1
    Press the button, and the desk will move to the height that was previously set for that button.

  • Select Height Setting 2
    Press the button, and the desk will move to the height that was previously set for that button.

  • Select Height Setting 3
    Press the button, and the desk will move to the height that was previously set for that button.

Save Current Height Setting
Short-press the button, and the screen will show. ‘S-’ Press the , , or button to save the current height setting to that button. When you press the , , or button, the desk will move to the height that was previously set for that button. Any button-press will stop the  desk.

Settings

  • Reset
    Press and hold the button until ‘rst’ is displayed. Continue holding until the desk goes down to its lowest level and comes back up slightly.
    Release the button, and reset is complete. If the button is released during the reset procedure, reset will stop. The desk won’t work until reset is done correctly.

  • Child Lock
    Press and hold the and buttons together for 5 seconds to turn child lock on. The screen will show ‘LOC’ and the buttons will be disabled.
    Turn child lock off the same way.

  • Setting Menu
    Press and hold the S button for 3 seconds, “S–” will be displayed.
    Then short-press the S button to enter setup mode. Short-press the ↑ or ↓ button to navigate through the menu or adjust the settings.
    Short-press the S button to enter next menu or save the changes.
    Short-press the 1 button to return to the previous menu. If there is no button-press for 20 seconds, it will exit setting mode.

  • Power-Saving Mode
    The screen will turn off if there is no button-press for a minute. Any button- press will turn the screen on again.

Protection Mode Error Codes

| Standby Overvoltage Protection: Standby voltage too high.
Power off the desk, check the connection between power and the controller, and power on again. If error  code persists, please contact technical support.
---|---
| Power Supply Overvoltage Protection: Input voltage too high.
If the correct AC adapter is being used, power off the desk, check the connection between power and the  controller, and power on again. If error code persists, please contact technical support.
| Operating Overvoltage Protection: Operating voltage too high. Power off the desk, check the connection  between power and the controller, and power on again. If error code persists, please contact technical  support.
| Overheating Protection: When the motor has been working continuously for too long, it will stop  operating to prevent overheating. Wait for at least 18 minutes (until error code disappears) before making  any further height adjustment.
| Power Supply Overvoltage Protection (during use): Input voltage too high. Error clears when power  supply voltage returns to normal. If error code persists, please contact technical support.
| Reset Warning: Continue to complete reset.
| Short Circuit Protection: Power off, check the cable connections, and power back on again. If error  persists, please contact technical support.
| Overloading Protection: Max load exceeded. Error code will persist for 20 seconds (DO NOT operate).  Take the things off the desk and confirm there is no mechanical damage before trying again.
| Motor Phase Error Protection: Power off, check the cable connection between the motor and the  controller, and power back on again. Then follow the reset instructions. If error code persists, please  contact technical support.
| Sensor Malfunction Warning: Motor sensor can’t be detected. Power off, check the cable connection  between the motor and the controller, and power back on again.
Then follow the reset instructions. If error code persists, please contact technical support.
| Anti-Collision System Warning: Impact detected. The desk will move 2″ (50mm) in the opposite direction  and stop.
| Cable Disconnection Warning: Check motor and controller cable connections. Normal operation should  return once all connectors are properly connected. If error code persists, please contact technical support.
| Mechanical Failure Warning: Check if there is any structural damage or motor fault.

OLIXIS D-ELT001-4824 Electric Height Adjustable Sit Stand Ergonomic Desk
Computer Workstations - Parts 1

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals