OLIXIS ELT-P4024 Electric Standing Desk Instruction Manual

OLIXIS ELT-P4024 Electric Standing Desk

Product Information

Specifications:

• Model: ELT-P4024
• Type: Electric Standing Desk
• Contact: HJ-Customer-Service@outlook.com
• Phone: (909)637-7665 | (909)637-7593
• Operating Hours: EST 9:00AM – 17:00PM

Product Usage Instructions

Assembly:

1. Unbox all components carefully.
2. Follow the step-by-step assembly instructions provided in the manual.
3. Ensure all parts are securely tightened.

Operation:

1. Plug the desk into a power source.
2. Use the control panel to adjust the desk height as needed.
3. Be gentle when adjusting the desk to avoid any damage.

Maintenance:

1. Keep the desk surface clean and free from dust.
2. Regularly check for any loose screws or parts.
3. Avoid placing heavy objects on the desk to prevent strain on the motor.

FAQ

Q: What should I do if the desk is not moving up or down?
A: Check the power source and ensure the desk is plugged in properly. If the issue persists, contact customer service for assistance.

Q: Can I program preset heights on the desk?
A: Depending on the model, some electric standing desks offer programmable height settings. Refer to the manual for specific instructions.

Q: How do I clean the desk surface?
A: Use a mild cleaning solution and a soft cloth to wipe down the desk surface. Avoid harsh chemicals that may damage the finish.

HJ-Customer-Service@outlook.com
(909)637-7665 | (909)637-7593

PARTS

TOOLS

Please read the installation instructions carefully before installation.

INSTRUCTION

STEP 1
Align the holes of Left Leg (2) and Drive Rod (4),Using Wrench(M-G)to secure both with Screw (M-A).

STEP 2
Insert the drive rod(4) into the hole in the right leg (3). If it is not possible to insert, please rotate the right leg (3) slightly until the inner hexagon matches.

STEP 3
As shown, use Wrench (M-H), install Beam (1) to the Legs (2&3) with Screws (M-8)*6.

STEP 4
Using Wrench(M-H), install Leg Base (6)2 to the Legs (2&3) respectively with Screws (M-C)8.

STEP 5
Use screwdriver , install Side Plate (5)2 on each side of the Legs (2&3) with Screws (M-F)4.

STEP 6

STEP 7
Fix Boards (7a&7b) with Wooden Pin (13)4. Use screwdriver with Screws (M-D) 8, install Desk Connection Plate (11)3 to the middle of the Boards , and Desk Connection Hook (8)2 to both sides of the Boards.

STEP 8
Fix Silicone Sheet (15)*10 to the corresponding hole position on the Boards (7 a& 7b).

STEP 9
Use screwdriver, secure the Leg part to the Boards (7a&7b) with Screws (M-E)10. Please align the Silicone Sheet (15)10.

STEP 10
As shown, connect the motor at the Left Leg (2), Hand Controller (9) and Power Supply (10) in turn.

Step 11
Using screwdriver install Hand Controller (9) to the Board (7a) with Screws (M-0)2. Secure the connecting cable with Cable Clip (14)2 and glue it to the bottom of the Board.

STEP 12
Insert Cable Hole Cover (12)*2 into the hole in the Board (7b).

Using the Controller

• Raise the Desk
  Press the button to raise the desk continuously until it reaches the highest position or the button is released.

• Lower the Desk
  Press the button to lower the desk continuously until it reaches the lowest position or the button is released.

• Select Height Setting 1
  Press the  1 button, and the desk will move to the height that was previously set for that button.

• Select Height Setting 2
  Press the 2 button, and the desk will move to the height that was previously set for that button.

• Select Height Setting 3
  Press the 3 button, and the desk will move to the height that was previously set for that button.

Save Current Height Setting
Short-press the button, and the screen will show ‘S-‘ .Press the 1 , 2 , or 3 button to save the current height setting to that button. When you press the 1 , 2 , or 3 button, the desk will move to the height that was previously set for that button. Any button-press will stop the desk.

Settings

• Reset
  Press and hold the~ button until ‘rst’ is displayed. Continue holding until the desk goes down to its lowest level and comes back up slightly.
  Release the button, and reset is complete. If the button is released during the reset procedure, reset will stop. The desk won’t work until reset is done correctly.

• Child Lock
  Press and hold the and buttons together for 5 seconds to turn child lock on. The screen will show ‘LOC’ and the buttons will be disabled.
  Turn child lock o the same way.

• Settings Menu
  Press and hold the button for 5 seconds to enter the settings menu. Short- press the button to navigate through the menu.
  Short-press the or button to adjust the settings. Long-press the or button to quickly adjust the height settings. Press and hold the button again to save the changes. ‘SUS’ will be displayed if saving is successful (or ‘FAL’ if saving fails). If there is no button press for 10 seconds, the settings menu will be exited automatically.

• Power-Saving Mode
  The screen will turn o if there is no button press for a minute. Any button press will turn the screen on again.

Protection Mode Error Codes

Technical Support
(909)637-7665 | (909)637-7593

Other Info
HJ-Customer-Service@outlook.com

Thank you for choosing this product. We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don’t hesitate to contact us.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>