OLIXIS HJ-1368-F Drafting Tall Standing Desk Counter Height Office Chairs Instruction Manual

June 15, 2024
OLIXIS

MANUAL
INSTRUCTION

OLIXIS HJ-1368-F Drafting Tall Standing Desk Counter Height Office
Chairs

Model: C-1368-F

Package List

  • Without further ado, we kindly suggest you to list all parts needed for the chair first.

OLIXIS HJ-1368-F Drafting Tall Standing Desk Counter Height Office Chairs -
Package List

Assembly Instruction

  • Step 1:
    Turn the Base (6) upside down, then insert Base Legs (7) one by one to Base.
    Use the Wrench (14) to screw Ten Bolts (9) into the pre-drilled screw holes to fix the Base and the Base Legs.
    OLIXIS HJ-1368-F Drafting Tall Standing Desk Counter Height Office Chairs -
Assembly 1 Step 2:
    Press the Casters (8) into the holes at the end of each Base Leg. And then insert the Gas Lift (5) into the center hole of the Five-Star Base.
    The Foot Ring (13) should be placed over the Gas Lift and fix the Foot Ring on the Gas Lift. Remove the cover from the top of the Gas Lift.
    Note: Please match convex to concave or it can’t be installed correctly.
    OLIXIS HJ-1368-F Drafting Tall Standing Desk Counter Height Office Chairs -
Assembly 2

  • Step 3:
    Turn the Seat Cushion (2) upside down and align the hole position of the Armrest (3)1(L)1(R) with the pre-drilled hole position under the Seat Cushion.
    Attach the Armrest (3)1(L)1(R) to the Seat Cushion (2) with Six Bolts (12), using the Wrench (14).
    All bolts do not need to be tightened, they only need to be fixed in half.
    Note 1: The “Front” mark on the Armrests and the “Front” mark on the Seat Cushion should be in the same direction.
    Note 2: Armrests are labeled with an “L” (left) or “R” (right) to show which side they should be placed on.

  • Step 4:
    Attach the Backrest (1) to the Armrest (3)1(L)1(R), Use the Wrench (14) to screw Four Bolts (11) on the left and right sides of the armrest to fix the back.
    All bolts do not need to be tightened,they only need to be fixed in a half.
    OLIXIS HJ-1368-F Drafting Tall Standing Desk Counter Height Office Chairs -
Assembly 4

  • Step 5:
    100% tighten the Bolts (12) * 6 to fix the armrest.
    OLIXIS HJ-1368-F Drafting Tall Standing Desk Counter Height Office Chairs -
Assembly 5

  • Step 6:
    100% tightened the Bolt (11)* 4 to fix the armrest and chair back.
    OLIXIS HJ-1368-F Drafting Tall Standing Desk Counter Height Office Chairs -
Assembly 6

  • Step 7:
    Attach the Mechanism (4) to the Seat Cushion using Two Bolts (10) at the front and Two Bolts (10) at the back, tighten all the bolts with the Wrench (14).
    OLIXIS HJ-1368-F Drafting Tall Standing Desk Counter Height Office Chairs -
Assembly 7+

  • Step 8:
    Insert the slot on the back of the mechanism behind the cushion into the Gas Lift.
    OLIXIS HJ-1368-F Drafting Tall Standing Desk Counter Height Office Chairs -
Assembly 8 CAUTION:
    Make sure all bolts and screws are fully tightened before using chair.
    Lubricate all moving parts and tighten all bolts/screws every 6 month or whenever needed.

Instructions For Use

  1. Seat Height: Paddle-shaped lever on the right side
    OLIXIS HJ-1368-F Drafting Tall Standing Desk Counter Height Office Chairs -
Assembly* At the proper height, your feet should rest flat on the floor.

Safety And Maintenance

  • Do not stand on the chair, Do Not use the chair as a stepladder.
  • Use this product for seating one person at a time.
  • Do not use the chair unless all bolts and screws are firmly secured.
  • Avoid contact with sharp objects to prevent puncturing the fabric.
  • Every 6 months, check all bolts and screws to ensure they are tight.
  • To clean, spot clean only using a damp towel and mild cleaner, first test on a small, unseen area of fabric.
  • Chair weight limit not to exceed 250 lbs.

Safety Information

OLIXIS HJ-1368-F Drafting Tall Standing Desk Counter Height Office Chairs -
Safety

Limited Warranty

The producer promises to repair or replace any chair that is found to be defective in material or workmanship within one(1) and year from the date of original purchase so long as you, the original purchaser, still owns it.
This is your sole and exclusive remedy. This warranty is subject to the provisions below.

EXCLUSIONS:
This warranty does not apply and no other warranty applies to:
Normal wear and tear, which are to be expected over the course of ownership.
Misuse, abuse, or excessive use of the product.
Modifications or attachments to the product that are not approved by the manufacturer.
Products that were not installed, used or maintained in accordance with product instructions and warnings.
Products used for rental or commercial purposes.
Damage caused by the carrier in-transit is handled under separate terms.
SEATING USAGE:
Normal use for seating is identified as the equivalent of a single shift, forty- (40) hour workweek. To the extent that a seating product is used in a manner exceeding this, the applicable warranty period will be reduced in a pro-rata manner.
Some retailers might have custom models imported directly from the factory and therefore are not supported by our local service team because we don’t have the correct parts, please contact your retailer directly for support. If you have any questions about that  we will be happy to assist and identify those items.

RETURN POLICY:
We adopt a 30 days return policy which means that all products purchased on this website may be returned to us within the timeframe. You need to contact us within 30 days after the product(s) came into your possession and the product(s) must be returned to  us without any undue delays.
Returned products must be returned in the same condition as they were sent and they must be sent in its original packaging.
If the product is not faulty, (i.e. if you changed your mind or if you are unhappy with the product for some other reason), the cost of shipping will all on you. And it is your responsibility that the package arrives safely to us so we recommend that you use a courier  service where it is possible to track the shipment.
If the product is faulty when you receive it please contact us and we will help you out (see more information under Manufacturer Warranty).
We reserve the right to give a partial refund in cases when the product(s) is not in an unused condition, is damaged or has missing parts not due to our error.

HOW RETURNS WORK:
Contact us through the contact form on our website and attach the invoice to the message as proof of purchase. And please also write the reason for the return.
We will then get back to you as soon as possible with information on where to send the product(s).
As soon as we have received the product(s) and made an inspection we will inform you of our decision.
If a refund is approved we will automatically credit the purchase to your credit card or original method of payment.
If the product(s) is damaged, not in its original condition or missing parts we will inform you if you are eligible for a partial refund. This is decided from case to case depending on the severity of the damages or what parts are missing.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals