Goodyear GY003409 Shatterproof in Channel Window Deflectors Instruction Manual

Goodyear GY003409 Shatterproof in Channel Window Deflectors

SIDE WINDOW DEFLECTORS

• Before installing the deflectors, please read the manual.
• Incorrect installation of deflectors can cause damage or injury

ATTENTION! IMPORTANT INFORMATION!
ATTENTION! Read the installation instructions carefully and follow all POINTS in the text! Incorrectly installed deflectors can be dangerous.

• Deactivate the safety features of the vehicle if they do not allow you to close the window and make sure to check the car instruction manual.
• After installing the deflectors, leave the car windows closed for 72 hours.
• We strongly recommend installing the deflectors at temperatures between 62.5°F/17°C and 77°F/25°C.
• IMPORTANT INFORMATION! Clean the grease off the installation surface with a supplied alcohol wipe. If the deflector installation process is not followed, the manufacturer does not guarantee the secure installation of the product.

COMPLETE SET

• 4 Piece Set (2 Piece Set) (the product may differ from the illustration in the instructions)

ATTENTION! Protective film, DO NOT REMOVE!

HOW TO INSTALL THE SIDE WINDOW DEFLECTORS

1. Deflector frame
2. The back section of the deflector
3. The front section of the deflector

FRONT DEFLECTORS

REAR DEFLECTORS

ATTENTION! Clean the installation surface with a supplied alcohol wipe. If the deflector installation process is not followed, the manufacturer does not guarantee the secure installation of the product.

1. Make sure the vehicle windows are clean and dry. Next, lower the side windows completely and clean the grease off the inner surface of the window channel with an alcohol wipe.
2. Remove the protective liner from the tape on the deflector.
3. Place the front part of the deflector to the lower frame of the window as shown in the picture.
4. Shift the deflector forward, fitting the deflector frame into the channel completely. Make sure the deflector is placed above the lower window frame.
5. Bending the centre part of the deflector outwards, insert the back part of the deflector into the channel, leaving a gap above it.
6. Starting with the front part of the deflector, insert it into the window channel.
7. Immediately after installing the deflector, adjust its position by carefully pulling it outwards.
8. To ensure the best installation of the deflector and the best adhesion between the tape and the surface of the rubber seal, it is strongly recommended that you use the plastic blade, moving it slowly between the window’s inner rubber seal and the deflector.
9. Raise the window until it touches the deflector. Carefully pulling the deflector outwards, roll the window up with abrupt movements. Repeat this action 4-5 times, then leave the window closed.
10. Repeat points 1.1 to 1.9 on the opposite side of the vehicle.

REAR DEFLECTORS (FOR FOUR-DOOR VEHICLES)

1. Make sure the car windows are clean and dry. Next, lower the side windows completely and clean the grease off the inner surface of the window channel with an alcohol wipe.
2. To position the fixture, bend the edge of the rubber seal from the back frame of the window by 2-3 inches by using the provided special plastic blade as shown in the illustration.
3. Place the fastening bracket in the channel and return the rubber seal to its original position. 1 – Rubber seal; 2 – Fastening bracket; 3 – Plastic blade; 4 – Metal body frame of the door.
4. The illustration demonstrates how to position the fastening bracket. 1 – Rubber seal; 2 – Deflector; 3 – Fastening bracket; 4 – Glass; 5 – Metal body frame of the door.
5. Bend the edge of the rubber seal from the front frame of the window by 2-3 inches. Place the fastening bracket in the channel and return the rubber seal to its original position.
6. Remove the protective liner from the tape on the deflector.
7. The deflector must be installed starting at the rear. To do so, place the rear section of the deflector frame into the channel and move the front section upwards. Position the entire deflector frame into the window channel, placing the frame between the fastening brackets and the rubber seal as is shown in the illustration.
8. Immediately after installing the deflector, adjust its position by carefully pulling it outwards.
9. To ensure the best installation of the deflector and the best adhesion between the tape and the surface of the rubber seal, it is strongly recommended that you use the plastic blade, moving it slowly between the window’s inner rubber seal and the deflector.
10. Raise the window until it touches the deflector. Carefully pulling the deflector outwards, roll up the window with abrupt movements. Repeat this action 4-5 times, then leave the window closed.
11. Repeat points 2.1 to 2.10 on the opposite side of the vehicle.

CONGRATULATIONS!
We hope you enjoy the appearance of your unique and durable Deflectors!

• If you have any questions about warranty, technical aid, or requests for missing (lost) parts, do not hesitate to use our website: www.goodyear-deflectors.com.
• For assistance please contact customer service by phone at + 1 888311 11 25 or by email at help@goodyear-deflectors.com.

Goodyear (and Winged Foot Design) and Blimp Design are trademarks of The Goodyear Tire & Rubber Company used under license by PROFIMPORT LLC, Building 3, Mayakovskogo Str. 1A, Ryazan, Russia. Copyright 2021 The Goodyear Tire & Rubber Company.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>