Stinger SPXDDASH Universal Double Din Mounting Kit Gauge Style Radio Installation Guide
- June 14, 2024
- Stinger
Table of Contents
SPXDDASH Universal Double Din Mounting Kit Gauge Style Radio
Installation Guide
Vehicle Fitment
The SPXDDASH is a universal mounting kit that can be used on any vehicle that
can accommodate a double din radio. It is used in conjunction with an
aftermarket double din dash kit (not included). When installed, the SPX-DDASH
converts the double din opening to accommodate a 3-Inch round gauge style
marine/off-road radio.
Recommended Tools
Phillips Screwdriver
Parts List
ASSEMBLY
Attach a Side Bracket to each side of the Main Frame using two #10 X 3/8”
screws per side.
NOTE: Side Brackets are the same and can be used on left or
right.
Mounting the Radio
Mount the radio following the radio manufacturers directions.
NOTE: The SPXDDASH has mounting holes pre-drilled for mounting the
Stinger SPXM1Media Player. UP Arrows need to be facing up to center the
SPXM1.
Mounting In Aftermarket Dash Kit
Once assembled, the SPXDDASH is the same dimensions as a standard double DIN
radio and has multiple mounting holes on the side brackets for mounting using
an aftermarket double DIN dash kit (not included). Always follow the
instructions that come with the dash kit. Below are a few example types of
mounting.
For dash kits that have side brackets and mount to the sub-dash or when using
the factory radio mounting brackets, simply align the brackets to the SPXDDASH
sides in the desired position and secure the side brackets with screws. For
dash kits that have a main frame and side brackets, align the SPXDDASH to the
desired position and depth and secure with screws.
When Things Don’t Quite Line Up
Some aftermarket dash kits are designed to accommodate radio’s that have a
longer “step” around the front face. This may prevent the SPXDDASH from
sitting flush to the dash kit. (FIG 1)
In those cases, removing some material from the backside of the dash kit will
allow the SPXDDASH to move forward and sit flush.
Using a file or Dremel, remove enough material to
allow the SPXDDASH to be positioned flush. (FIG 2)
This will need to be done at the top and bottom on both sides. 
With the dash kit
“notched”, the front face of the SPXDDASH can be aligned flush with dash kit.
(FIG 3)
LIMITED WARRANTY:
Stinger warrants this product to be free of defects in materials and
workmanship for a period of one (1) years from the original date of purchase.
This warranty is not transferable and applies only to the original purchaser
from an authorized Stinger dealer in the United States of America only. Should
service be necessary under this warranty for any reason due to manufacturing
defect or malfunction, Stinger will (at its discretion), repair or replace the
defective product with new or remanufactured product at no charge.
Damage caused by the following is not covered under warranty: accident,
misuse, abuse, product modification or neglect, failure to follow installation
instructions, unauthorized repair attempts, misrepresentations by the seller.
This arrantly does not cover incidental or consequential damages and does not
cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to
accident or normal wear and tear is not covered under warranty.
INTERNATIONAL WARRANTIES:
Products purchased outside the United States of America are covered only by
that country’s Authorized Stinger reseller and not by Stinger. Consumers
needing service or warranty information for these products must contact that
country’s reseller for information.
TECHNICAL SUPPORT:
727-592-5991
Mon-Fri 9AM-8PM EST
Sat 9AM-7PM EST
support@aampglobal.com
© 2022 AAMP Global IG-SPXDDASH REV 082222V
Stinger is a Power Brand of AAMP Global
15500 Lightwave, Clearwater, Florida 33760
P: 888-228-5560
support@stingerelectronics.com
www.stingerelectronics.com
© 2022 AAMP Global IG-SPXDDASH REV 082222
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>