Stinger Audio MT-600.4M Marine Amplifier Installation Guide

June 1, 2024
Stinger AUDIO

Stinger Audio-LOGO

Stinger Audio MT-600.4M Marine Amplifier

Stinger-Audio MT-600.4M Marine-Amplifier-PRODUCT

Monoblock Amplifier

Power Connections

Stinger-Audio MT-600.4M Marine-Amplifier-FIG- \(1\)

Signal Connections

Stinger-Audio MT-600.4M Marine-Amplifier-FIG- \(2\)

Multi-Channel Amplifier

Power Connections

Stinger-Audio MT-600.4M Marine-Amplifier-FIG- \(3\)

Signal Connections

Amplifier Control

Monoblock Amplifier

Stinger-Audio MT-600.4M Marine-Amplifier-FIG- \(5\)

  1. Protect LED [PRT]
    Red when amplifier is powering up or in Protection Mode. See Troubleshooting for more information. Power LED [PWR] Blue when amplifier is ON. Clipping LED[CLIP] Red when amplifiers is clipping

  2. REMOTE
    Connect the PMTRMT2 Remote Bass Control knob here.

  3. INPUT
    Connect to line level output RCAs from head unit or line output converter (LOC).

  4. BRIDGE
    Used to connect two amplifiers together. See page 9.

  5. GAIN
    Used to adjust the input sensitivity to match the input level signal.

  6. Low Pass Filter [LPF]
    A low pass crossover for the subwoofer output. Variable from 40Hz to 180Hz.Generally set around 80Hz.

  7. SUBSONIC
    A high pass crossover for the subwoofer output. Variable from OFF to 50Hz. Generally set between 30-35Hz.

  8. Boost Frequency [FREQ]
    Selects the frequency to boost when adding BOOST. Variable from 30Hz to 80Hz.

  9. BOOST
    Boosts the selected frequency [FREQ] from 0dB to 12dB.

Multi-Channel Amplifier

Stinger-Audio MT-600.4M Marine-Amplifier-FIG- \(6\)

  1. Frequency Multiplier Multiplies crossover frequency by xl or x10

  2. Crossover Filter
    Low-pass filter [LPFJ, passes through the frequencies below the set frequency.
    High-pass filter [HPFJ passes through the frequencies above the set frequency.

  3. Input Mode
    Selection between 2ch input or 4ch input

  4. INPUT
    Connect to line level output RCAs from head unit or line output converter (LOC).

  5. Protect LED [PRT]
    Red when amplifier is powering up or in Protection Mode. See Troubleshooting for more information. Power LED [PWR] Blue when amplifier is ON. Clipping LED[CLIP] Red when amplifiers is clipping

  6. Crossover Frequency
    Set the crossover frequency point. Variable from 50Hz to 5kHz utilizing Multiplier switch.

  7. GAIN
    Used to adjust the input sensitivity to match the input level signal.

  8. REMOTE
    Connect the PMTRMT2 Remote Bass Control knob here.

MT-1800.lM Specs

RMS Power Ratings listed at less than 1% THD @ 14.4v

Stinger-Audio MT-600.4M Marine-Amplifier-FIG- \(7\)Stinger-Audio MT-600.4M Marine-Amplifier-FIG- \(8\)

MT-1000.lM Specs

RMS Power Ratings listed at less than 1% THD @ 14.4v

Stinger-Audio MT-600.4M Marine-Amplifier-FIG- \(9\)Stinger-Audio MT-600.4M Marine-Amplifier-FIG- \(10\)

MT-600.4M Specs

RMS Power Ratings listed at less than 1% THD @ 14.4v

Stinger-Audio MT-600.4M Marine-Amplifier-FIG- \(11\)Stinger-Audio MT-600.4M Marine-Amplifier-FIG-
\(12\)

Bridging Multi-Channel amplifier

Stinger-Audio MT-600.4M Marine-Amplifier-FIG- \(13\)

Bridging (Connecting) Two Mono Amplifiers
Connect Bridge Out on the Primary amplifier to Bridge In on the Secondary amplifier. Connect the Negative speaker output on the Primary amplifier to the Negative speaker output on the Secondary amplifier. Connect the Positive speaker output of the Primary amplifier to the positive speaker terminal. Connect the Positive speaker out put of the Secondary amplifier to the negative speaker terminal. 2 ohm minimum! All adjustments are made on the Primary amplifier.

Stinger-Audio MT-600.4M Marine-Amplifier-FIG- \(14\)

LIMITED WARRANTY

Stinger warrants this product to be free of defects in materials and workmanship for a period of one (1) year from the original date of purchase. This warranty is not transferable and applies only to the original purchaser from an authorized Stinger dealer in the United States of America. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction, Stinger will (at its discretion), repair or replace the defective product with the new or remanufactured product at no charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions, unauthorized repair attempts, and misrepresentations by the seller. This warranty does not cover incidental or consequential damages and does not cover the cost of removing or reinstalling the units). Cosmetic damage due to accident or normal wear and tear is not covered under warranty.

INTERNATIONAL WARRANTIES:
Products purchased outside the United States of America are covered only by that country’s Authorized Stinger reseller and not by Stinger. Consumers needing service or warranty information for these products must contact that country’s reseller for information.

STOP! Please DO NOT return it to the seller For help with installation, replacement parts, warranty or returns, please contact us directly at 727-732-3114 or support@stingerelectronics.com Stinger is a Power Brand of AAMP Global 15500 Lightwave, Clearwater, Florida 33760  2024 AAMP Global MCAMP-IG REV 010624

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals