Stinger MT-700.1 MT Series Monoblock Amplifiers Installation Guide
- June 3, 2024
- Stinger
Table of Contents
Stinger MT-700.1 MT Series Monoblock Amplifiers Installation Guide
Power Connections
Signal Connections
Amplifier Controls
-
Protect LED [PRT] Red when amplifier is powering up or in Protection Mode. See Troubleshooting for more information.
Power LED [PWR] Blue when amplifier is ON -
REMOTE Connect the SA1RBC Remote Bass Control knob here.
-
INPUT Connect to line level output RCAs from head unit or line output converter (LOC).
-
BRIDGE Used to connect two amplifiers together. See page 8.
-
GAIN Used to adjust the input sensitivity to match theinput level signal.
-
Low Pass Filter [LPF] A low pass crossover for the subwoofer output. Variable from 40Hz to 180Hz.Generally set around 80Hz.
-
SUBSONIC A high pass crossover for the subwoofer output. Variable from OFF to 50Hz. Generally set between 30-35Hz.
-
Boost Frequency [FREQ] Selects the frequency to boost when adding BOOST. Variable from 30Hz to 80Hz.
-
OOST Boosts the selected frequency[FREQ] from 0dB to 12dB.
MT-2000.1 Specs
RMS Power Ratings listed at less than 1% THD @ 14.4v
- 1Ω 2000W X 1
- 2Ω 1500W X 1
- 4Ω 800W X 1
- Bridged RMS Rating / 2Ω Minimum 3800W x 1
- Signal to Noise (@ CEA Standard) -93dB
- Input Sensitivity 0.2-6v
- Gain 0.2v – 6v
- Crossover Control, Linkwitz-Riley: SUB 0Hz – 50Hz (Subsonic) LP 40Hz – 180Hz @ 12dB/Oct
- Bass-BoostFrequencyRange 30-80 Hz Bass-Boost Q 0-12dB
- Frequency Response(+- 1dB) 10Hz – 180Hz
- Efficiency (Average) 80%
- Topology Class Class D
- Remote Bass Control Yep (Included)
- Operating Voltage 9V to 16V
- Power Terminal 0/1 Gauge
- Speaker Terminal 8 Gauge
- Recommended External Fusing 200A
MT-1500.1 Specs
RMS Power Ratings listed at less than 1% THD @ 14.4v
- 1Ω 1500W X 1
- 2Ω 1000W X 1
- 4Ω 550W X 1
- Bridged RMS Rating / 2Ω Minimum 2800W x 1
- Signal to Noise (@ CEA Standard) -93dB
- Input Sensitivity 0.2-6v
- Gain 0.2v – 6v
- Crossover Control, Linkwitz-Riley: SUB 0Hz – 50Hz (Subsonic) LP 40Hz – 180Hz @ 12dB/Oct
- Bass-BoostFrequencyRange 30-80 Hz
- Bass-Boost Q 0-12dB
- FrequencyResponse (+- 1dB) 10Hz – 180Hz
- Efficiency (Average) 82%
- Topology Class Class D
- Remote Bass Control Yep (Included)
- Operating Voltage 9V to 16V
- Power Terminal 4 Gauge
- Speaker Terminal 8 Gauge
- Recommended External Fusing 150A
MT-1000.1 Specs
RMS Power Ratings listed at less than 1% THD @ 14.4v
- 1Ω 1000W X 1
- 2Ω 700W X 1
- 4Ω 400W X 1
- Bridged RMS Rating / 2Ω Minimum 1800W x 1
- Signal to Noise (@ CEA Standard) -93dB
- Input Sensitivity 0.2-6v
- Gain 0.2v – 6v
- Crossover Control, Linkwitz-Riley: SUB 0Hz – 50Hz (Subsonic) LP 40Hz – 180Hz @ 12dB/Oct
- Bass-Boost Frequency Range 30-80 Hz
- Bass-Boost Q 0-12dB
- Frequency Response(+- 1dB) 10Hz – 180Hz
- Efficiency (Average) 82%
- Topology Class Class D
- Remote Bass Control Yep (Included)
- Operating Voltage 9V to 16V
- Power Terminal 4 Gauge
- Speaker Terminal 8 Gauge
- Recommended External Fusing 100A
MT-700.1 Specs
RMS Power Ratings listed at less than 1% THD @ 14.4v
- 1Ω 700W X 1
- 2Ω 500W X 1
- 4Ω 300W X 1
- Bridged RMS Rating / 2Ω Minimum 1200W x 1
- Signal to Noise (@ CEA Standard) -93dB
- Input Sensitivity 0.2-6v
- Gain 0.2v – 6v
- Crossover Control, Linkwitz-Riley: SUB 0Hz – 50Hz (Subsonic) LP 40Hz – 180Hz @ 12dB/Oct
- Bass-Boost Frequency Range 30-80 Hz
- Bass-Boost Q 0-12dB
- Frequency Response(+- 1dB) 10Hz – 180Hz
- Efficiency (Average) 85%
- Topology Class Class D
- Remote Bass Control Yep (Included)
- Operating Voltage 9V to 16V
- Power Terminal 4 Gauge
- Speaker Terminal 8 Gauge
- Recommended External Fusing 80A
Bridging (Connecting) Two Amplifiers
Connect Bridge Out on the Primary amplifier to Bridge In on the Secondary amplifier. Connect the Negative speaker output on the Primary amplifier to the Negative speaker output on the Secondary amplifier. Connect the Positive speaker output of the Primary amplifier to the positive speaker terminal. Connect the Positive speaker out put of the Secondary amplifier to the negative speaker terminal. 2 ohm minimum! All adjustments are made on the Primary amplifier.
LIMITED WARRANTY
Stinger warrants this product to be free of defects in materials and workmanship for a period of one (1) years from the original date of purchase. This warranty is not transferable and applies only to the original purchaser from an authorized Stinger dealer in the United States of America only. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction, Stinger will (at its discretion), repair or replace the defective product with new or remanufactured product at no charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions, unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not covered under warranty.
INTERNATIONAL WARRANTIES:
Products purchased outside the United States of America are covered only by that country’s Authorized Stinger reseller and not by Stinger. Consumers needing service or warranty information for these products must contact that country’s reseller for information.
STOP! Please DO NOT return to seller
For help with installation, replacement parts, warranty or returns,
please contact us directly at
727-732-3114 or
support@stingerelectronics.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>